diff mbox series

[v3,5/5] arm64: dts: rockchip: fix the pcie refclock oscillator on Rock 5 ITX

Message ID 20240828101503.1478491-6-heiko@sntech.de (mailing list archive)
State New
Headers show
Series Binding and driver for gated-fixed-clocks | expand

Commit Message

Heiko Stübner Aug. 28, 2024, 10:15 a.m. UTC
The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and its
SATA controller with 2 lanes each. The supply for the refclk oscillator is
the same that supplies the M.2 slot, but the SATA controller port is
supplied by a different rail.

This leads to the effect that if the PCIe30x4 controller for the M.2
probes first, everything works normally. But if the PCIe30x2 controller
that is connected to the SATA controller probes first, it will hang on
the first DBI read as nothing will have enabled the refclock before.

Fix this by describing the clock generator with its supplies so that
both controllers can reference it as needed.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
 .../boot/dts/rockchip/rk3588-rock-5-itx.dts   | 38 ++++++++++++++++++-
 1 file changed, 36 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts
index d0b922b8d67e..2d0bcf90bf0f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts
@@ -72,6 +72,15 @@  hdd-led2 {
 		};
 	};
 
+	/* Unnamed gated oscillator: 100MHz,3.3V,3225 */
+	pcie30_port0_refclk: pcie30_port1_refclk: pcie-oscillator {
+		compatible = "gated-fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "pcie30_refclk";
+		vdd-supply = <&vcc3v3_pi6c_05>;
+	};
+
 	fan0: pwm-fan {
 		compatible = "pwm-fan";
 		#cooling-cells = <2>;
@@ -146,13 +155,14 @@  vcc3v3_lan: vcc3v3_lan_phy2: regulator-vcc3v3-lan {
 		vin-supply = <&vcc_3v3_s3>;
 	};
 
-	vcc3v3_mkey: regulator-vcc3v3-mkey {
+	/* The PCIE30x4_PWREN_H controls two regulators */
+	vcc3v3_mkey: vcc3v3_pi6c_05: regulator-vcc3v3-pi6c-05 {
 		compatible = "regulator-fixed";
 		enable-active-high;
 		gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pcie30x4_pwren_h>;
-		regulator-name = "vcc3v3_mkey";
+		regulator-name = "vcc3v3_pi6c_05";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		startup-delay-us = <5000>;
@@ -513,6 +523,18 @@  &pcie30phy {
 
 /* ASMedia ASM1164 Sata controller */
 &pcie3x2 {
+	/*
+	 * The board has a "pcie_refclk" oscillator that needs enabling,
+	 * so add it to the list of clocks.
+	 */
+	clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>,
+		 <&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>,
+		 <&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>,
+		 <&pcie30_port1_refclk>;
+	clock-names = "aclk_mst", "aclk_slv",
+		      "aclk_dbi", "pclk",
+		      "aux", "pipe",
+		      "ref";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie30x2_perstn_m1_l>;
 	reset-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
@@ -522,6 +544,18 @@  &pcie3x2 {
 
 /* M.2 M.key */
 &pcie3x4 {
+	/*
+	 * The board has a "pcie_refclk" oscillator that needs enabling,
+	 * so add it to the list of clocks.
+	 */
+	clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>,
+		 <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>,
+		 <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>,
+		 <&pcie30_port0_refclk>;
+	clock-names = "aclk_mst", "aclk_slv",
+		      "aclk_dbi", "pclk",
+		      "aux", "pipe",
+		      "ref";
 	num-lanes = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie30x4_perstn_m1_l>;