diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c
index 93cfc83..4c35526 100644
--- a/drivers/i2c/busses/i2c-rk3x.c
+++ b/drivers/i2c/busses/i2c-rk3x.c
@@ -97,6 +97,8 @@ struct rk3x_i2c {
 	/* Hardware resources */
 	void __iomem *regs;
 	struct clk *clk;
+	struct notifier_block clk_rate_nb;
+	unsigned long clk_freq;
 
 	/* Settings */
 	unsigned int scl_frequency;
@@ -428,18 +430,127 @@ out:
 	return IRQ_HANDLED;
 }
 
-static void rk3x_i2c_set_scl_rate(struct rk3x_i2c *i2c, unsigned long scl_rate)
+/**
+ * Calculate divider value for desired SCL frequency
+ *
+ * @clk_rate: I2C input clock rate
+ * @scl_rate: Desired SCL rate
+ * @div:      Divider output
+ *
+ * Return:    0 on success, -EINVAL on unreachable SCL rate. In that case
+ *            a best-effort divider value is returned in div.
+ **/
+static int rk3x_i2c_calc_div(unsigned long clk_rate, unsigned long scl_rate,
+			     unsigned int *div)
 {
-	unsigned long i2c_rate = clk_get_rate(i2c->clk);
-	unsigned int div;
+	/* Range checks */
+	if (scl_rate > clk_rate / 16) {
+		/* Return a best effort divider */
+		*div = 0;
+		return -EINVAL;
+	}
+
+	if (scl_rate < clk_rate / (16 * 65536)) {
+		/* Return a best effort divider */
+		*div = 0xFFFF;
+		return -EINVAL;
+	}
 
 	/* set DIV = DIVH = DIVL
 	 * SCL rate = (clk rate) / (8 * (DIVH + 1 + DIVL + 1))
 	 *          = (clk rate) / (16 * (DIV + 1))
 	 */
-	div = DIV_ROUND_UP(i2c_rate, scl_rate * 16) - 1;
+	*div = DIV_ROUND_UP(clk_rate, scl_rate * 16) - 1;
 
+	return 0;
+}
+
+/**
+ * Setup divider register for desired SCL frequency
+ *
+ * @scl_rate: Desired SCL Rate
+ **/
+static void rk3x_i2c_set_scl_rate(struct rk3x_i2c *i2c, unsigned long scl_rate)
+{
+	unsigned long i2c_rate = clk_get_rate(i2c->clk);
+	unsigned int div;
+
+	if (rk3x_i2c_calc_div(i2c_rate, scl_rate, &div) != 0) {
+		dev_warn(i2c->dev, "Could not reach desired SCL freq %lu Hz\n",
+			 scl_rate
+		);
+	}
+
+	/*
+	 * We might be called from rk3x_i2c_probe or from the clk rate change
+	 * notifier. In that case, the i2c clk is not running. So enable it
+	 * explicitly here during the register write.
+	 *
+	 * Writing the register with halted clock crashes the system at least on
+	 * RK3288.
+	 */
+
+	clk_enable(i2c->clk);
 	i2c_writel(i2c, (div << 16) | (div & 0xffff), REG_CLKDIV);
+	clk_disable(i2c->clk);
+}
+
+/**
+ * rk3x_i2c_clk_notifier_cb - Clock rate change callback
+ * @nb:		Pointer to notifier block
+ * @event:	Notification reason
+ * @data:	Pointer to notification data object
+ *
+ * The callback checks whether a valid bus frequency can be generated after the
+ * change. If so, the change is acknowledged, otherwise the change is aborted.
+ * New dividers are written to the HW in the pre- or post change notification
+ * depending on the scaling direction.
+ *
+ * Code adapted from i2c-cadence.c.
+ *
+ * Return:	NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
+ *		to acknowedge the change, NOTIFY_DONE if the notification is
+ *		considered irrelevant.
+ */
+static int rk3x_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
+				    event, void *data)
+{
+	struct clk_notifier_data *ndata = data;
+	struct rk3x_i2c *i2c = container_of(nb, struct rk3x_i2c, clk_rate_nb);
+
+	switch (event) {
+	case PRE_RATE_CHANGE:
+	{
+		unsigned int div;
+
+		if (rk3x_i2c_calc_div(ndata->new_rate, i2c->scl_frequency,
+				      &div) != 0) {
+			return NOTIFY_STOP;
+		}
+
+		i2c->clk_freq = ndata->new_rate;
+
+		/* scale up */
+		if (ndata->new_rate > ndata->old_rate)
+			rk3x_i2c_set_scl_rate(i2c, ndata->new_rate);
+
+		return NOTIFY_OK;
+	}
+	case POST_RATE_CHANGE:
+		i2c->clk_freq = ndata->new_rate;
+
+		/* scale down */
+		if (ndata->new_rate < ndata->old_rate)
+			rk3x_i2c_set_scl_rate(i2c, ndata->new_rate);
+		return NOTIFY_OK;
+	case ABORT_RATE_CHANGE:
+		/* scale up */
+		if (ndata->new_rate > ndata->old_rate)
+			rk3x_i2c_set_scl_rate(i2c, ndata->old_rate);
+		return NOTIFY_OK;
+	default:
+		return NOTIFY_DONE;
+	}
 }
 
 /**
@@ -536,9 +647,6 @@ static int rk3x_i2c_xfer(struct i2c_adapter *adap,
 
 	clk_enable(i2c->clk);
 
-	/* The clock rate might have changed, so setup the divider again */
-	rk3x_i2c_set_scl_rate(i2c, i2c->scl_frequency);
-
 	i2c->is_last_msg = false;
 
 	/*
@@ -724,16 +832,31 @@ static int rk3x_i2c_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	i2c->clk_rate_nb.notifier_call = rk3x_i2c_clk_notifier_cb;
+	ret = clk_notifier_register(i2c->clk, &i2c->clk_rate_nb);
+	if (ret != 0) {
+		dev_err(&pdev->dev, "Unable to register clock notifier\n");
+		goto err_clk;
+	}
+
+	i2c->clk_freq = clk_get_rate(i2c->clk);
+
+	clk_enable(i2c->clk);
+	rk3x_i2c_set_scl_rate(i2c, i2c->scl_frequency);
+	clk_disable(i2c->clk);
+
 	ret = i2c_add_adapter(&i2c->adap);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "Could not register adapter\n");
-		goto err_clk;
+		goto err_clk_notifier;
 	}
 
 	dev_info(&pdev->dev, "Initialized RK3xxx I2C bus at %p\n", i2c->regs);
 
 	return 0;
 
+err_clk_notifier:
+	clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb);
 err_clk:
 	clk_unprepare(i2c->clk);
 	return ret;
