@@ -30,6 +30,7 @@
#define SDMMC_CLKSEL_TIMING(x, y, z) (SDMMC_CLKSEL_CCLK_SAMPLE(x) | \
SDMMC_CLKSEL_CCLK_DRIVE(y) | \
SDMMC_CLKSEL_CCLK_DIVIDER(z))
+#define SDMMC_CLKSEL_WAKEUP_INT BIT(11)
#define EXYNOS4210_FIXED_CIU_CLK_DIV 2
#define EXYNOS4412_FIXED_CIU_CLK_DIV 4
@@ -100,6 +101,49 @@ static int dw_mci_exynos_setup_clock(struct dw_mci *host)
return 0;
}
+#ifdef CONFIG_PM_SLEEP
+static int dw_mci_exynos_suspend(struct device *dev)
+{
+ struct dw_mci *host = dev_get_drvdata(dev);
+
+ return dw_mci_suspend(host);
+}
+
+static int dw_mci_exynos_resume(struct device *dev)
+{
+ struct dw_mci *host = dev_get_drvdata(dev);
+
+ return dw_mci_resume(host);
+}
+
+/**
+ * dw_mci_exynos_resume_noirq - Exynos-specific resume code
+ *
+ * On exynos5420 there is a silicon errata that will sometimes leave the
+ * WAKEUP_INT bit in the CLKSEL register asserted. This bit is 1 to indicate
+ * that it fired and we can clear it by writing a 1 back. Clear it to prevent
+ * interrupts from going off constantly.
+ *
+ * We run this code on all exynos variants because it doesn't hurt.
+ */
+
+static int dw_mci_exynos_resume_noirq(struct device *dev)
+{
+ struct dw_mci *host = dev_get_drvdata(dev);
+ u32 clksel;
+
+ clksel = mci_readl(host, CLKSEL);
+ if (clksel & SDMMC_CLKSEL_WAKEUP_INT)
+ mci_writel(host, CLKSEL, clksel);
+
+ return 0;
+}
+#else
+#define dw_mci_exynos_suspend NULL
+#define dw_mci_exynos_resume NULL
+#define dw_mci_exynos_resume_noirq NULL
+#endif /* CONFIG_PM_SLEEP */
+
static void dw_mci_exynos_prepare_command(struct dw_mci *host, u32 *cmdr)
{
/*
@@ -187,13 +231,20 @@ static int dw_mci_exynos_probe(struct platform_device *pdev)
return dw_mci_pltfm_register(pdev, drv_data);
}
+const struct dev_pm_ops dw_mci_exynos_pmops = {
+ SET_SYSTEM_SLEEP_PM_OPS(dw_mci_exynos_suspend, dw_mci_exynos_resume)
+ .resume_noirq = dw_mci_exynos_resume_noirq,
+ .thaw_noirq = dw_mci_exynos_resume_noirq,
+ .restore_noirq = dw_mci_exynos_resume_noirq,
+};
+
static struct platform_driver dw_mci_exynos_pltfm_driver = {
.probe = dw_mci_exynos_probe,
.remove = __exit_p(dw_mci_pltfm_remove),
.driver = {
.name = "dwmmc_exynos",
.of_match_table = dw_mci_exynos_match,
- .pm = &dw_mci_pltfm_pmops,
+ .pm = &dw_mci_exynos_pmops,
},
};
If the WAKEUP_INT is asserted at wakeup and not cleared, we'll end up looping around forever. This has been seen to happen on exynos5420 silicon despite the fact that we haven't enabled any wakeup events due to a silicon errata. It is safe to do on all exynos variants. Signed-off-by: Doug Anderson <dianders@chromium.org> --- Changes in v6: - Took out TODO comment copied from main platform code. Changes in v5: - Cleaned up dw_mci_exynos_resume_noirq() comment as per Seungwon. - Don't memcpy dev_pm_ops structure, define a new one. Changes in v4: - Take Seungwon's suggestion and don't add any dw_mmc-pltfm code. Changes in v3: - Add freeze/thaw and poweroff/restore noirq entries. Changes in v2: - Use suspend_noirq as per James Hogan. drivers/mmc/host/dw_mmc-exynos.c | 53 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 52 insertions(+), 1 deletion(-)