| Message ID | 1382074659-31130-2-git-send-email-arun.kk@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, Apologies for the late reply. I have a few comments, but nothing major. On Fri, Oct 18, 2013 at 06:37:28AM +0100, Arun Kumar K wrote: > The patch adds the DT binding documentation for Samsung > Exynos5 SoC series imaging subsystem (FIMC-IS). > > Signed-off-by: Arun Kumar K <arun.kk@samsung.com> > Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> > --- > .../devicetree/bindings/media/exynos5-fimc-is.txt | 84 ++++++++++++++++++++ > 1 file changed, 84 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/exynos5-fimc-is.txt > > diff --git a/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt > new file mode 100644 > index 0000000..0525417 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt > @@ -0,0 +1,84 @@ > +Samsung EXYNOS5 SoC series Imaging Subsystem (FIMC-IS) > +------------------------------------------------------ > + > +The camera subsystem on Samsung Exynos5 SoC has some changes relative > +to previous SoC versions. Exynos5 has almost similar MIPI-CSIS and > +FIMC-LITE IPs but has a much improved version of FIMC-IS which can > +handle sensor controls and camera post-processing operations. The > +Exynos5 FIMC-IS has a dedicated ARM Cortex A5 processor, many > +post-processing blocks (ISP, DRC, FD, ODC, DIS, 3DNR) and two > +dedicated scalers (SCC and SCP). > + > +fimc-is node > +------------ > + > +Required properties: > + > +- compatible : must be "samsung,exynos5250-fimc-is" s/must be/should contain/ > +- reg : physical base address and size of the memory mapped > + registers > +- interrupt-parent : parent interrupt controller I don't think this is actually required in all cases. It's a standard property that people can add if it happens to be required in a particular instance. > +- interrupts : fimc-is interrupt to the parent interrupt controller Is this the only interrupt the device generates? If so: - interrupts: interrupt-specifier for the fimc-is interrupt. > +- clocks : list of clock specifiers, corresponding to entries in > + clock-names property > +- clock-names : must contain "isp", "mcu_isp", "isp_div0", "isp_div1", > + "isp_divmpwm", "mcu_isp_div0", "mcu_isp_div1" entries, > + matching entries in the clocks property > +- samsung,pmu : phandle to the Power Management Unit (PMU) node > + > +i2c-isp (ISP I2C bus controller) nodes > +-------------------------------------- > +The i2c-isp node is defined as the child node of fimc-is. There are multiple of these, so how about the following instead: The i2c-isp nodes should be children of the fimc-is node. It might be worth pointing out that ranges, #address-cells, and #size-cells should be present as appropriate. > + > +Required properties: > + > +- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212, > + Exynos4412 and Exynos5250 SoCs Similarly, s/should be/must contain/ > +- reg : physical base address and length of the registers set > +- clocks : must contain gate clock specifier for this controller > +- clock-names : must contain "i2c_isp" entry I'd prefer clocks to be described as for the simc-is, with clock names being something like: - clock-names: should contain "i2c_isp" for the gate clock. > + > +For the i2c-isp node, it is required to specify a pinctrl state named "default", > +according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. I'd prefer a mention of pinctrl-0 and pinctrl-names, as that's what most other bindings do. Also, as this is described as required it should be in the example. > + > +Device tree nodes of the image sensors controlled directly by the FIMC-IS > +firmware must be child nodes of their corresponding ISP I2C bus controller node. > +The data link of these image sensors must be specified using the common video > +interfaces bindings, defined in video-interfaces.txt. These don't seem to be in the example and probably should be. Otherwise, this looks fine. With those points fixed up: Acked-by: Mark Rutland <mark.rutland@arm.com> Thanks, Mark. -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Mark, Thank you for the review. Will address your comments. Regards Arun On Tue, Oct 29, 2013 at 5:02 AM, Mark Rutland <mark.rutland@arm.com> wrote: > Hi, > > Apologies for the late reply. I have a few comments, but nothing major. > > On Fri, Oct 18, 2013 at 06:37:28AM +0100, Arun Kumar K wrote: >> The patch adds the DT binding documentation for Samsung >> Exynos5 SoC series imaging subsystem (FIMC-IS). >> >> Signed-off-by: Arun Kumar K <arun.kk@samsung.com> >> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> >> --- >> .../devicetree/bindings/media/exynos5-fimc-is.txt | 84 ++++++++++++++++++++ >> 1 file changed, 84 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/exynos5-fimc-is.txt >> >> diff --git a/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt >> new file mode 100644 >> index 0000000..0525417 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt >> @@ -0,0 +1,84 @@ >> +Samsung EXYNOS5 SoC series Imaging Subsystem (FIMC-IS) >> +------------------------------------------------------ >> + >> +The camera subsystem on Samsung Exynos5 SoC has some changes relative >> +to previous SoC versions. Exynos5 has almost similar MIPI-CSIS and >> +FIMC-LITE IPs but has a much improved version of FIMC-IS which can >> +handle sensor controls and camera post-processing operations. The >> +Exynos5 FIMC-IS has a dedicated ARM Cortex A5 processor, many >> +post-processing blocks (ISP, DRC, FD, ODC, DIS, 3DNR) and two >> +dedicated scalers (SCC and SCP). >> + >> +fimc-is node >> +------------ >> + >> +Required properties: >> + >> +- compatible : must be "samsung,exynos5250-fimc-is" > > s/must be/should contain/ > >> +- reg : physical base address and size of the memory mapped >> + registers >> +- interrupt-parent : parent interrupt controller > > I don't think this is actually required in all cases. It's a standard property > that people can add if it happens to be required in a particular instance. > >> +- interrupts : fimc-is interrupt to the parent interrupt controller > > Is this the only interrupt the device generates? If so: > > - interrupts: interrupt-specifier for the fimc-is interrupt. > >> +- clocks : list of clock specifiers, corresponding to entries in >> + clock-names property >> +- clock-names : must contain "isp", "mcu_isp", "isp_div0", "isp_div1", >> + "isp_divmpwm", "mcu_isp_div0", "mcu_isp_div1" entries, >> + matching entries in the clocks property >> +- samsung,pmu : phandle to the Power Management Unit (PMU) node >> + >> +i2c-isp (ISP I2C bus controller) nodes >> +-------------------------------------- >> +The i2c-isp node is defined as the child node of fimc-is. > > There are multiple of these, so how about the following instead: > > The i2c-isp nodes should be children of the fimc-is node. > > It might be worth pointing out that ranges, #address-cells, and #size-cells > should be present as appropriate. > >> + >> +Required properties: >> + >> +- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212, >> + Exynos4412 and Exynos5250 SoCs > > Similarly, s/should be/must contain/ > >> +- reg : physical base address and length of the registers set >> +- clocks : must contain gate clock specifier for this controller >> +- clock-names : must contain "i2c_isp" entry > > I'd prefer clocks to be described as for the simc-is, with clock names being > something like: > > - clock-names: should contain "i2c_isp" for the gate clock. > >> + >> +For the i2c-isp node, it is required to specify a pinctrl state named "default", >> +according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. > > I'd prefer a mention of pinctrl-0 and pinctrl-names, as that's what most other > bindings do. > > Also, as this is described as required it should be in the example. > >> + >> +Device tree nodes of the image sensors controlled directly by the FIMC-IS >> +firmware must be child nodes of their corresponding ISP I2C bus controller node. >> +The data link of these image sensors must be specified using the common video >> +interfaces bindings, defined in video-interfaces.txt. > > These don't seem to be in the example and probably should be. > > Otherwise, this looks fine. With those points fixed up: > > Acked-by: Mark Rutland <mark.rutland@arm.com> > > Thanks, > Mark. -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt new file mode 100644 index 0000000..0525417 --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos5-fimc-is.txt @@ -0,0 +1,84 @@ +Samsung EXYNOS5 SoC series Imaging Subsystem (FIMC-IS) +------------------------------------------------------ + +The camera subsystem on Samsung Exynos5 SoC has some changes relative +to previous SoC versions. Exynos5 has almost similar MIPI-CSIS and +FIMC-LITE IPs but has a much improved version of FIMC-IS which can +handle sensor controls and camera post-processing operations. The +Exynos5 FIMC-IS has a dedicated ARM Cortex A5 processor, many +post-processing blocks (ISP, DRC, FD, ODC, DIS, 3DNR) and two +dedicated scalers (SCC and SCP). + +fimc-is node +------------ + +Required properties: + +- compatible : must be "samsung,exynos5250-fimc-is" +- reg : physical base address and size of the memory mapped + registers +- interrupt-parent : parent interrupt controller +- interrupts : fimc-is interrupt to the parent interrupt controller +- clocks : list of clock specifiers, corresponding to entries in + clock-names property +- clock-names : must contain "isp", "mcu_isp", "isp_div0", "isp_div1", + "isp_divmpwm", "mcu_isp_div0", "mcu_isp_div1" entries, + matching entries in the clocks property +- samsung,pmu : phandle to the Power Management Unit (PMU) node + +i2c-isp (ISP I2C bus controller) nodes +-------------------------------------- +The i2c-isp node is defined as the child node of fimc-is. + +Required properties: + +- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212, + Exynos4412 and Exynos5250 SoCs +- reg : physical base address and length of the registers set +- clocks : must contain gate clock specifier for this controller +- clock-names : must contain "i2c_isp" entry + +For the i2c-isp node, it is required to specify a pinctrl state named "default", +according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. + +Device tree nodes of the image sensors controlled directly by the FIMC-IS +firmware must be child nodes of their corresponding ISP I2C bus controller node. +The data link of these image sensors must be specified using the common video +interfaces bindings, defined in video-interfaces.txt. + +Example: + + fimc_is: fimc-is@13000000 { + compatible = "samsung,exynos5250-fimc-is"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + reg = <0x13000000 0x200000>; + interrupt-parent = <&combiner>; + interrupts = <19 1>; + clocks = <&clock 346>, <&clock 347>, <&clock 512>, + <&clock 513>, <&clock 514>, <&clock 515>, + <&clock 516>; + clock-names = "isp", "mcu_isp", "isp_div0", "isp_div1", + "isp_divmpwm", "mcu_isp_div0", + "mcu_isp_div1"; + samsung,pmu = <&pmu>; + + i2c0_isp: i2c-isp@13130000 { + compatible = "samsung,exynos4212-i2c-isp"; + reg = <0x13130000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock 352>; + clock-names = "i2c_isp"; + }; + + i2c1_isp: i2c-isp@13140000 { + compatible = "samsung,exynos4212-i2c-isp"; + reg = <0x13140000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock 353>; + clock-names = "i2c_isp"; + }; + };