| Message ID | 1394029108-2531-4-git-send-email-k.debski@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Kamil, On Wednesday 05 March 2014 07:48 PM, Kamil Debski wrote: > Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic > PHY framework. The driver includes support for the Exynos 4x10 and 4x12 > SoC families. Pls fix these errors which I get while applying your patch. Applying: phy: Add new Exynos USB 2.0 PHY driver /home/kishon/repos/linux-phy/.git/rebase-apply/patch:534: new blank line at EOF. + /home/kishon/repos/linux-phy/.git/rebase-apply/patch:869: new blank line at EOF. + /home/kishon/repos/linux-phy/.git/rebase-apply/patch:1098: new blank line at EOF. + /home/kishon/repos/linux-phy/.git/rebase-apply/patch:1171: new blank line at EOF. + warning: 4 lines add whitespace errors. Thanks Kishon > > Signed-off-by: Kamil Debski <k.debski@samsung.com> > --- > .../devicetree/bindings/phy/samsung-phy.txt | 53 ++++ > Documentation/phy/samsung-usb2.txt | 134 ++++++++ > drivers/phy/Kconfig | 29 ++ > drivers/phy/Makefile | 3 + > drivers/phy/phy-exynos4210-usb2.c | 262 ++++++++++++++++ > drivers/phy/phy-exynos4x12-usb2.c | 329 ++++++++++++++++++++ > drivers/phy/phy-samsung-usb2.c | 223 +++++++++++++ > drivers/phy/phy-samsung-usb2.h | 67 ++++ > 8 files changed, 1100 insertions(+) > create mode 100644 Documentation/phy/samsung-usb2.txt > create mode 100644 drivers/phy/phy-exynos4210-usb2.c > create mode 100644 drivers/phy/phy-exynos4x12-usb2.c > create mode 100644 drivers/phy/phy-samsung-usb2.c > create mode 100644 drivers/phy/phy-samsung-usb2.h > > diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt > index c0fccaa..bf955ab 100644 > --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt > +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt > @@ -20,3 +20,56 @@ Required properties: > - compatible : should be "samsung,exynos5250-dp-video-phy"; > - reg : offset and length of the Display Port PHY register set; > - #phy-cells : from the generic PHY bindings, must be 0; > + > +Samsung S5P/EXYNOS SoC series USB PHY > +------------------------------------------------- > + > +Required properties: > +- compatible : should be one of the listed compatibles: > + - "samsung,exynos4210-usb2-phy" > + - "samsung,exynos4x12-usb2-phy" > +- reg : a list of registers used by phy driver > + - first and obligatory is the location of phy modules registers > +- samsung,sysreg-phandle - handle to syscon used to control the system registers > +- samsung,pmureg-phandle - handle to syscon used to control PMU registers > +- #phy-cells : from the generic phy bindings, must be 1; > +- clocks and clock-names: > + - the "phy" clock is required by the phy module, used as a gate > + - the "ref" clock is used to get the rate of the clock provided to the > + PHY module > + > +The first phandle argument in the PHY specifier identifies the PHY, its > +meaning is compatible dependent. For the currently supported SoCs (Exynos 4210 > +and Exynos 4212) it is as follows: > + 0 - USB device ("device"), > + 1 - USB host ("host"), > + 2 - HSIC0 ("hsic0"), > + 3 - HSIC1 ("hsic1"), > + > +Exynos 4210 and Exynos 4212 use mode switching and require that mode switch > +register is supplied. > + > +Example: > + > +For Exynos 4412 (compatible with Exynos 4212): > + > +usbphy: phy@125b0000 { > + compatible = "samsung,exynos4x12-usb2-phy"; > + reg = <0x125b0000 0x100>; > + clocks = <&clock 305>, <&clock 2>; > + clock-names = "phy", "ref"; > + status = "okay"; > + #phy-cells = <1>; > + samsung,sysreg-phandle = <&sys_reg>; > + samsung,pmureg-phandle = <&pmu_reg>; > +}; > + > +Then the PHY can be used in other nodes such as: > + > +phy-consumer@12340000 { > + phys = <&usbphy 2>; > + phy-names = "phy"; > +}; > + > +Refer to DT bindings documentation of particular PHY consumer devices for more > +information about required PHYs and the way of specification. > diff --git a/Documentation/phy/samsung-usb2.txt b/Documentation/phy/samsung-usb2.txt > new file mode 100644 > index 0000000..0c8e260 > --- /dev/null > +++ b/Documentation/phy/samsung-usb2.txt > @@ -0,0 +1,134 @@ > +.------------------------------------------------------------------------------+ > +| Samsung USB 2.0 PHY adaptation layer | > ++-----------------------------------------------------------------------------+' > + > +| 1. Description > ++---------------- > + > +The architecture of the USB 2.0 PHY module in Samsung SoCs is similar > +among many SoCs. In spite of the similarities it proved difficult to > +create a one driver that would fit all these PHY controllers. Often > +the differences were minor and were found in particular bits of the > +registers of the PHY. In some rare cases the order of register writes or > +the PHY powering up process had to be altered. This adaptation layer is > +a compromise between having separate drivers and having a single driver > +with added support for many special cases. > + > +| 2. Files description > ++---------------------- > + > +- phy-samsung-usb2.c > + This is the main file of the adaptation layer. This file contains > + the probe function and provides two callbacks to the Generic PHY > + Framework. This two callbacks are used to power on and power off the > + phy. They carry out the common work that has to be done on all version > + of the PHY module. Depending on which SoC was chosen they execute SoC > + specific callbacks. The specific SoC version is selected by choosing > + the appropriate compatible string. In addition, this file contains > + struct of_device_id definitions for particular SoCs. > + > +- phy-samsung-usb2.h > + This is the include file. It declares the structures used by this > + driver. In addition it should contain extern declarations for > + structures that describe particular SoCs. > + > +| 3. Supporting SoCs > ++-------------------- > + > +To support a new SoC a new file should be added to the drivers/phy > +directory. Each SoC's configuration is stored in an instance of the > +struct samsung_usb2_phy_config. > + > +struct samsung_usb2_phy_config { > + const struct samsung_usb2_common_phy *phys; > + unsigned int num_phys; > + bool has_mode_switch; > +}; > + > +The num_phys is the number of phys handled by the driver. *phys is an > +array that contains the configuration for each phy. The has_mode_switch > +property is a boolean flag that determines whether the SoC has USB host > +and device on a single pair of pins. If so, a special register has to > +be modified to change the internal routing of these pins between a USB > +device or host module. > + > +For example the configuration for Exynos 4210 is following: > + > +const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = { > + .has_mode_switch = 0, > + .num_phys = EXYNOS4210_NUM_PHYS, > + .phys = exynos4210_phys, > + .rate_to_clk = exynos4210_rate_to_clk, > +} > + > +- int (*rate_to_clk)(unsigned long, u32 *) > + The rate_to_clk callback is to convert the rate of the clock > + used as the reference clock for the PHY module to the value > + that should be written in the hardware register. > + > +The exynos4210_phys configuration array is as follows: > + > +static const struct samsung_usb2_common_phy exynos4210_phys[] = { > + { > + .label = "device", > + .id = EXYNOS4210_DEVICE, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + { > + .label = "host", > + .id = EXYNOS4210_HOST, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + { > + .label = "hsic0", > + .id = EXYNOS4210_HSIC0, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + { > + .label = "hsic1", > + .id = EXYNOS4210_HSIC1, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + {}, > +}; > + > +- int (*power_on)(struct samsung_usb2_phy_instance *); > +- int (*power_off)(struct samsung_usb2_phy_instance *); > + These two callbacks are used to power on and power off the phy > + by modifying appropriate registers. > + > +Final change to the driver is adding appropriate compatible value to the > +phy-samsung-usb2.c file. In case of Exynos 4210 the following lines were > +added to the struct of_device_id samsung_usb2_phy_of_match[] array: > + > +#ifdef CONFIG_PHY_EXYNOS4210_USB2 > + { > + .compatible = "samsung,exynos4210-usb2-phy", > + .data = &exynos4210_usb2_phy_config, > + }, > +#endif > + > +To add further flexibility to the driver the Kconfig file enables to > +include support for selected SoCs in the compiled driver. The Kconfig > +entry for Exynos 4210 is following: > + > +config PHY_EXYNOS4210_USB2 > + bool "Support for Exynos 4210" > + depends on PHY_SAMSUNG_USB2 > + depends on CPU_EXYNOS4210 > + help > + Enable USB PHY support for Exynos 4210. This option requires that > + Samsung USB 2.0 PHY driver is enabled and means that support for this > + particular SoC is compiled in the driver. In case of Exynos 4210 four > + phys are available - device, host, HSCI0 and HSCI1. > + > +The newly created file that supports the new SoC has to be also added to the > +Makefile. In case of Exynos 4210 the added line is following: > + > +obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o > + > +After completing these steps the support for the new SoC should be ready. > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig > index dc1756c..fc5a44a 100644 > --- a/drivers/phy/Kconfig > +++ b/drivers/phy/Kconfig > @@ -96,4 +96,33 @@ config PHY_SUN4I_USB > This driver controls the entire USB PHY block, both the USB OTG > parts, as well as the 2 regular USB 2 host PHYs. > > +config PHY_SAMSUNG_USB2 > + tristate "Samsung USB 2.0 PHY driver" > + select GENERIC_PHY > + select MFD_SYSCON > + help > + Enable this to support the Samsung USB 2.0 PHY driver for Samsung > + SoCs. This driver provides the interface for USB 2.0 PHY. Support for > + particular SoCs has to be enabled in addition to this driver. Number > + and type of supported phys depends on the SoC. > + > +config PHY_EXYNOS4210_USB2 > + bool "Support for Exynos 4210" > + depends on PHY_SAMSUNG_USB2 > + depends on CPU_EXYNOS4210 > + help > + Enable USB PHY support for Exynos 4210. This option requires that > + Samsung USB 2.0 PHY driver is enabled and means that support for this > + particular SoC is compiled in the driver. In case of Exynos 4210 four > + phys are available - device, host, HSIC0 and HSIC1. > + > +config PHY_EXYNOS4X12_USB2 > + bool "Support for Exynos 4x12" > + depends on PHY_SAMSUNG_USB2 > + depends on (SOC_EXYNOS4212 || SOC_EXYNOS4412) > + help > + Enable USB PHY support for Exynos 4x12. This option requires that > + Samsung USB 2.0 PHY driver is enabled and means that support for this > + particular SoC is compiled in the driver. In case of Exynos 4x12 four > + phys are available - device, host, HSIC0 and HSIC1. > endmenu > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > index 5d0b59e..0ea36ff 100644 > --- a/drivers/phy/Makefile > +++ b/drivers/phy/Makefile > @@ -11,3 +11,6 @@ obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o > obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o > obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o > obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o > +obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-samsung-usb2.o > +obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o > +obj-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o > diff --git a/drivers/phy/phy-exynos4210-usb2.c b/drivers/phy/phy-exynos4210-usb2.c > new file mode 100644 > index 0000000..9970e81 > --- /dev/null > +++ b/drivers/phy/phy-exynos4210-usb2.c > @@ -0,0 +1,262 @@ > +/* > + * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4210 support > + * > + * Copyright (C) 2013 Samsung Electronics Co., Ltd. > + * Author: Kamil Debski <k.debski@samsung.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/delay.h> > +#include <linux/io.h> > +#include <linux/phy/phy.h> > +#include <linux/regmap.h> > +#include "phy-samsung-usb2.h" > + > +/* Exynos USB PHY registers */ > + > +/* PHY power control */ > +#define EXYNOS_4210_UPHYPWR 0x0 > + > +#define EXYNOS_4210_UPHYPWR_PHY0_SUSPEND BIT(0) > +#define EXYNOS_4210_UPHYPWR_PHY0_PWR BIT(3) > +#define EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR BIT(4) > +#define EXYNOS_4210_UPHYPWR_PHY0_SLEEP BIT(5) > +#define EXYNOS_4210_UPHYPWR_PHY0 ( \ > + EXYNOS_4210_UPHYPWR_PHY0_SUSPEND | \ > + EXYNOS_4210_UPHYPWR_PHY0_PWR | \ > + EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR | \ > + EXYNOS_4210_UPHYPWR_PHY0_SLEEP) > + > +#define EXYNOS_4210_UPHYPWR_PHY1_SUSPEND BIT(6) > +#define EXYNOS_4210_UPHYPWR_PHY1_PWR BIT(7) > +#define EXYNOS_4210_UPHYPWR_PHY1_SLEEP BIT(8) > +#define EXYNOS_4210_UPHYPWR_PHY1 ( \ > + EXYNOS_4210_UPHYPWR_PHY1_SUSPEND | \ > + EXYNOS_4210_UPHYPWR_PHY1_PWR | \ > + EXYNOS_4210_UPHYPWR_PHY1_SLEEP) > + > +#define EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND BIT(9) > +#define EXYNOS_4210_UPHYPWR_HSIC0_SLEEP BIT(10) > +#define EXYNOS_4210_UPHYPWR_HSIC0 ( \ > + EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND | \ > + EXYNOS_4210_UPHYPWR_HSIC0_SLEEP) > + > +#define EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND BIT(11) > +#define EXYNOS_4210_UPHYPWR_HSIC1_SLEEP BIT(12) > +#define EXYNOS_4210_UPHYPWR_HSIC1 ( \ > + EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND | \ > + EXYNOS_4210_UPHYPWR_HSIC1_SLEEP) > + > +/* PHY clock control */ > +#define EXYNOS_4210_UPHYCLK 0x4 > + > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_MASK (0x3 << 0) > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET 0 > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ (0x0 << 0) > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ (0x3 << 0) > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0) > + > +#define EXYNOS_4210_UPHYCLK_PHY0_ID_PULLUP BIT(2) > +#define EXYNOS_4210_UPHYCLK_PHY0_COMMON_ON BIT(4) > +#define EXYNOS_4210_UPHYCLK_PHY1_COMMON_ON BIT(7) > + > +/* PHY reset control */ > +#define EXYNOS_4210_UPHYRST 0x8 > + > +#define EXYNOS_4210_URSTCON_PHY0 BIT(0) > +#define EXYNOS_4210_URSTCON_OTG_HLINK BIT(1) > +#define EXYNOS_4210_URSTCON_OTG_PHYLINK BIT(2) > +#define EXYNOS_4210_URSTCON_PHY1_ALL BIT(3) > +#define EXYNOS_4210_URSTCON_PHY1_P0 BIT(4) > +#define EXYNOS_4210_URSTCON_PHY1_P1P2 BIT(5) > +#define EXYNOS_4210_URSTCON_HOST_LINK_ALL BIT(6) > +#define EXYNOS_4210_URSTCON_HOST_LINK_P0 BIT(7) > +#define EXYNOS_4210_URSTCON_HOST_LINK_P1 BIT(8) > +#define EXYNOS_4210_URSTCON_HOST_LINK_P2 BIT(9) > + > +/* Isolation, configured in the power management unit */ > +#define EXYNOS_4210_USB_ISOL_DEVICE_OFFSET 0x704 > +#define EXYNOS_4210_USB_ISOL_DEVICE BIT(0) > +#define EXYNOS_4210_USB_ISOL_HOST_OFFSET 0x708 > +#define EXYNOS_4210_USB_ISOL_HOST BIT(0) > + > +/* USBYPHY1 Floating prevention */ > +#define EXYNOS_4210_UPHY1CON 0x34 > +#define EXYNOS_4210_UPHY1CON_FLOAT_PREVENTION 0x1 > + > +/* Mode switching SUB Device <-> Host */ > +#define EXYNOS_4210_MODE_SWITCH_OFFSET 0x21c > +#define EXYNOS_4210_MODE_SWITCH_MASK 1 > +#define EXYNOS_4210_MODE_SWITCH_DEVICE 0 > +#define EXYNOS_4210_MODE_SWITCH_HOST 1 > + > +enum exynos4210_phy_id { > + EXYNOS4210_DEVICE, > + EXYNOS4210_HOST, > + EXYNOS4210_HSIC0, > + EXYNOS4210_HSIC1, > + EXYNOS4210_NUM_PHYS, > +}; > + > +/* > + * exynos4210_rate_to_clk() converts the supplied clock rate to the value that > + * can be written to the phy register. > + */ > +static int exynos4210_rate_to_clk(unsigned long rate, u32 *reg) > +{ > + switch (rate) { > + case 12 * MHZ: > + *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ; > + break; > + case 24 * MHZ: > + *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ; > + break; > + case 48 * MHZ: > + *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ; > + break; > + default: > + return -EINVAL; > + } > + > + return 0; > +} > + > +static void exynos4210_isol(struct samsung_usb2_phy_instance *inst, bool on) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + u32 offset; > + u32 mask; > + > + switch (inst->cfg->id) { > + case EXYNOS4210_DEVICE: > + offset = EXYNOS_4210_USB_ISOL_DEVICE_OFFSET; > + mask = EXYNOS_4210_USB_ISOL_DEVICE; > + break; > + case EXYNOS4210_HOST: > + offset = EXYNOS_4210_USB_ISOL_HOST_OFFSET; > + mask = EXYNOS_4210_USB_ISOL_HOST; > + break; > + default: > + return; > + }; > + > + regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask); > +} > + > +static void exynos4210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + u32 rstbits = 0; > + u32 phypwr = 0; > + u32 rst; > + u32 pwr; > + u32 clk; > + > + switch (inst->cfg->id) { > + case EXYNOS4210_DEVICE: > + phypwr = EXYNOS_4210_UPHYPWR_PHY0; > + rstbits = EXYNOS_4210_URSTCON_PHY0; > + break; > + case EXYNOS4210_HOST: > + phypwr = EXYNOS_4210_UPHYPWR_PHY1; > + rstbits = EXYNOS_4210_URSTCON_PHY1_ALL | > + EXYNOS_4210_URSTCON_PHY1_P0 | > + EXYNOS_4210_URSTCON_PHY1_P1P2 | > + EXYNOS_4210_URSTCON_HOST_LINK_ALL | > + EXYNOS_4210_URSTCON_HOST_LINK_P0; > + writel(on, drv->reg_phy + EXYNOS_4210_UPHY1CON); > + break; > + case EXYNOS4210_HSIC0: > + phypwr = EXYNOS_4210_UPHYPWR_HSIC0; > + rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 | > + EXYNOS_4210_URSTCON_HOST_LINK_P1; > + break; > + case EXYNOS4210_HSIC1: > + phypwr = EXYNOS_4210_UPHYPWR_HSIC1; > + rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 | > + EXYNOS_4210_URSTCON_HOST_LINK_P2; > + break; > + }; > + > + if (on) { > + clk = readl(drv->reg_phy + EXYNOS_4210_UPHYCLK); > + clk &= ~EXYNOS_4210_UPHYCLK_PHYFSEL_MASK; > + clk |= drv->ref_reg_val << EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET; > + writel(clk, drv->reg_phy + EXYNOS_4210_UPHYCLK); > + > + pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR); > + pwr &= ~phypwr; > + writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR); > + > + rst = readl(drv->reg_phy + EXYNOS_4210_UPHYRST); > + rst |= rstbits; > + writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST); > + udelay(10); > + rst &= ~rstbits; > + writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST); > + /* The following delay is necessary for the reset sequence to be > + * completed */ > + udelay(80); > + } else { > + pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR); > + pwr |= phypwr; > + writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR); > + } > +} > + > +static int exynos4210_power_on(struct samsung_usb2_phy_instance *inst) > +{ > + /* Order of initialisation is important - first power then isolation */ > + exynos4210_phy_pwr(inst, 1); > + exynos4210_isol(inst, 0); > + > + return 0; > +} > + > +static int exynos4210_power_off(struct samsung_usb2_phy_instance *inst) > +{ > + exynos4210_isol(inst, 1); > + exynos4210_phy_pwr(inst, 0); > + > + return 0; > +} > + > + > +static const struct samsung_usb2_common_phy exynos4210_phys[] = { > + { > + .label = "device", > + .id = EXYNOS4210_DEVICE, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + { > + .label = "host", > + .id = EXYNOS4210_HOST, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + { > + .label = "hsic0", > + .id = EXYNOS4210_HSIC0, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + { > + .label = "hsic1", > + .id = EXYNOS4210_HSIC1, > + .power_on = exynos4210_power_on, > + .power_off = exynos4210_power_off, > + }, > + {}, > +}; > + > +const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = { > + .has_mode_switch = 0, > + .num_phys = EXYNOS4210_NUM_PHYS, > + .phys = exynos4210_phys, > + .rate_to_clk = exynos4210_rate_to_clk, > +}; > + > diff --git a/drivers/phy/phy-exynos4x12-usb2.c b/drivers/phy/phy-exynos4x12-usb2.c > new file mode 100644 > index 0000000..40c90f9 > --- /dev/null > +++ b/drivers/phy/phy-exynos4x12-usb2.c > @@ -0,0 +1,329 @@ > +/* > + * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4x12 support > + * > + * Copyright (C) 2013 Samsung Electronics Co., Ltd. > + * Author: Kamil Debski <k.debski@samsung.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/delay.h> > +#include <linux/io.h> > +#include <linux/phy/phy.h> > +#include <linux/regmap.h> > +#include "phy-samsung-usb2.h" > + > +/* Exynos USB PHY registers */ > + > +/* PHY power control */ > +#define EXYNOS_4x12_UPHYPWR 0x0 > + > +#define EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND BIT(0) > +#define EXYNOS_4x12_UPHYPWR_PHY0_PWR BIT(3) > +#define EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR BIT(4) > +#define EXYNOS_4x12_UPHYPWR_PHY0_SLEEP BIT(5) > +#define EXYNOS_4x12_UPHYPWR_PHY0 ( \ > + EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND | \ > + EXYNOS_4x12_UPHYPWR_PHY0_PWR | \ > + EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR | \ > + EXYNOS_4x12_UPHYPWR_PHY0_SLEEP) > + > +#define EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND BIT(6) > +#define EXYNOS_4x12_UPHYPWR_PHY1_PWR BIT(7) > +#define EXYNOS_4x12_UPHYPWR_PHY1_SLEEP BIT(8) > +#define EXYNOS_4x12_UPHYPWR_PHY1 ( \ > + EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND | \ > + EXYNOS_4x12_UPHYPWR_PHY1_PWR | \ > + EXYNOS_4x12_UPHYPWR_PHY1_SLEEP) > + > +#define EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND BIT(9) > +#define EXYNOS_4x12_UPHYPWR_HSIC0_PWR BIT(10) > +#define EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP BIT(11) > +#define EXYNOS_4x12_UPHYPWR_HSIC0 ( \ > + EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND | \ > + EXYNOS_4x12_UPHYPWR_HSIC0_PWR | \ > + EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP) > + > +#define EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND BIT(12) > +#define EXYNOS_4x12_UPHYPWR_HSIC1_PWR BIT(13) > +#define EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP BIT(14) > +#define EXYNOS_4x12_UPHYPWR_HSIC1 ( \ > + EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND | \ > + EXYNOS_4x12_UPHYPWR_HSIC1_PWR | \ > + EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP) > + > +/* PHY clock control */ > +#define EXYNOS_4x12_UPHYCLK 0x4 > + > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK (0x7 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET 0 > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6 (0x0 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ (0x1 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2 (0x3 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ (0x4 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ (0x5 << 0) > +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ (0x7 << 0) > + > +#define EXYNOS_4x12_UPHYCLK_PHY0_ID_PULLUP BIT(3) > +#define EXYNOS_4x12_UPHYCLK_PHY0_COMMON_ON BIT(4) > +#define EXYNOS_4x12_UPHYCLK_PHY1_COMMON_ON BIT(7) > + > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_MASK (0x7f << 10) > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_OFFSET 10 > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_12MHZ (0x24 << 10) > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_15MHZ (0x1c << 10) > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_16MHZ (0x1a << 10) > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_19MHZ2 (0x15 << 10) > +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_20MHZ (0x14 << 10) > + > +/* PHY reset control */ > +#define EXYNOS_4x12_UPHYRST 0x8 > + > +#define EXYNOS_4x12_URSTCON_PHY0 BIT(0) > +#define EXYNOS_4x12_URSTCON_OTG_HLINK BIT(1) > +#define EXYNOS_4x12_URSTCON_OTG_PHYLINK BIT(2) > +#define EXYNOS_4x12_URSTCON_HOST_PHY BIT(3) > +#define EXYNOS_4x12_URSTCON_PHY1 BIT(4) > +#define EXYNOS_4x12_URSTCON_HSIC0 BIT(5) > +#define EXYNOS_4x12_URSTCON_HSIC1 BIT(6) > +#define EXYNOS_4x12_URSTCON_HOST_LINK_ALL BIT(7) > +#define EXYNOS_4x12_URSTCON_HOST_LINK_P0 BIT(8) > +#define EXYNOS_4x12_URSTCON_HOST_LINK_P1 BIT(9) > +#define EXYNOS_4x12_URSTCON_HOST_LINK_P2 BIT(10) > + > +/* Isolation, configured in the power management unit */ > +#define EXYNOS_4x12_USB_ISOL_OFFSET 0x704 > +#define EXYNOS_4x12_USB_ISOL_OTG BIT(0) > +#define EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET 0x708 > +#define EXYNOS_4x12_USB_ISOL_HSIC0 BIT(0) > +#define EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET 0x70c > +#define EXYNOS_4x12_USB_ISOL_HSIC1 BIT(0) > + > +/* Mode switching SUB Device <-> Host */ > +#define EXYNOS_4x12_MODE_SWITCH_OFFSET 0x21c > +#define EXYNOS_4x12_MODE_SWITCH_MASK 1 > +#define EXYNOS_4x12_MODE_SWITCH_DEVICE 0 > +#define EXYNOS_4x12_MODE_SWITCH_HOST 1 > + > +enum exynos4x12_phy_id { > + EXYNOS4x12_DEVICE, > + EXYNOS4x12_HOST, > + EXYNOS4x12_HSIC0, > + EXYNOS4x12_HSIC1, > + EXYNOS4x12_NUM_PHYS, > +}; > + > +/* > + * exynos4x12_rate_to_clk() converts the supplied clock rate to the value that > + * can be written to the phy register. > + */ > +static int exynos4x12_rate_to_clk(unsigned long rate, u32 *reg) > +{ > + /* EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK */ > + > + switch (rate) { > + case 9600 * KHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6; > + break; > + case 10 * MHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ; > + break; > + case 12 * MHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ; > + break; > + case 19200 * KHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2; > + break; > + case 20 * MHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ; > + break; > + case 24 * MHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ; > + break; > + case 50 * MHZ: > + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ; > + break; > + default: > + return -EINVAL; > + } > + > + return 0; > +} > + > +static void exynos4x12_isol(struct samsung_usb2_phy_instance *inst, bool on) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + u32 offset; > + u32 mask; > + > + switch (inst->cfg->id) { > + case EXYNOS4x12_DEVICE: > + case EXYNOS4x12_HOST: > + offset = EXYNOS_4x12_USB_ISOL_OFFSET; > + mask = EXYNOS_4x12_USB_ISOL_OTG; > + break; > + case EXYNOS4x12_HSIC0: > + offset = EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET; > + mask = EXYNOS_4x12_USB_ISOL_HSIC0; > + break; > + case EXYNOS4x12_HSIC1: > + offset = EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET; > + mask = EXYNOS_4x12_USB_ISOL_HSIC1; > + break; > + default: > + return; > + }; > + > + regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask); > +} > + > +static void exynos4x12_setup_clk(struct samsung_usb2_phy_instance *inst) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + u32 clk; > + > + clk = readl(drv->reg_phy + EXYNOS_4x12_UPHYCLK); > + clk &= ~EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK; > + clk |= drv->ref_reg_val << EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET; > + writel(clk, drv->reg_phy + EXYNOS_4x12_UPHYCLK); > +} > + > +static void exynos4x12_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + u32 rstbits = 0; > + u32 phypwr = 0; > + u32 rst; > + u32 pwr; > + u32 mode = 0; > + u32 switch_mode = 0; > + > + switch (inst->cfg->id) { > + case EXYNOS4x12_DEVICE: > + phypwr = EXYNOS_4x12_UPHYPWR_PHY0; > + rstbits = EXYNOS_4x12_URSTCON_PHY0; > + mode = EXYNOS_4x12_MODE_SWITCH_DEVICE; > + switch_mode = 1; > + break; > + case EXYNOS4x12_HOST: > + phypwr = EXYNOS_4x12_UPHYPWR_PHY1; > + rstbits = EXYNOS_4x12_URSTCON_HOST_PHY; > + mode = EXYNOS_4x12_MODE_SWITCH_HOST; > + switch_mode = 1; > + break; > + case EXYNOS4x12_HSIC0: > + phypwr = EXYNOS_4x12_UPHYPWR_HSIC0; > + rstbits = EXYNOS_4x12_URSTCON_HSIC1 | > + EXYNOS_4x12_URSTCON_HOST_LINK_P0 | > + EXYNOS_4x12_URSTCON_HOST_PHY; > + break; > + case EXYNOS4x12_HSIC1: > + phypwr = EXYNOS_4x12_UPHYPWR_HSIC1; > + rstbits = EXYNOS_4x12_URSTCON_HSIC1 | > + EXYNOS_4x12_URSTCON_HOST_LINK_P1; > + break; > + }; > + > + if (on) { > + if (switch_mode) > + regmap_update_bits(drv->reg_sys, > + EXYNOS_4x12_MODE_SWITCH_OFFSET, > + EXYNOS_4x12_MODE_SWITCH_MASK, mode); > + > + pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR); > + pwr &= ~phypwr; > + writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR); > + > + rst = readl(drv->reg_phy + EXYNOS_4x12_UPHYRST); > + rst |= rstbits; > + writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST); > + udelay(10); > + rst &= ~rstbits; > + writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST); > + /* The following delay is necessary for the reset sequence to be > + * completed */ > + udelay(80); > + } else { > + pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR); > + pwr |= phypwr; > + writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR); > + } > +} > + > +static int exynos4x12_power_on(struct samsung_usb2_phy_instance *inst) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + > + inst->enabled = 1; > + exynos4x12_setup_clk(inst); > + exynos4x12_phy_pwr(inst, 1); > + exynos4x12_isol(inst, 0); > + > + /* Power on the device, as it is necessary for HSIC to work */ > + if (inst->cfg->id == EXYNOS4x12_HSIC0) { > + struct samsung_usb2_phy_instance *device = > + &drv->instances[EXYNOS4x12_DEVICE]; > + exynos4x12_phy_pwr(device, 1); > + exynos4x12_isol(device, 0); > + } > + > + return 0; > +} > + > +static int exynos4x12_power_off(struct samsung_usb2_phy_instance *inst) > +{ > + struct samsung_usb2_phy_driver *drv = inst->drv; > + struct samsung_usb2_phy_instance *device = > + &drv->instances[EXYNOS4x12_DEVICE]; > + > + inst->enabled = 0; > + exynos4x12_isol(inst, 1); > + exynos4x12_phy_pwr(inst, 0); > + > + if (inst->cfg->id == EXYNOS4x12_HSIC0 && !device->enabled) { > + exynos4x12_isol(device, 1); > + exynos4x12_phy_pwr(device, 0); > + } > + > + return 0; > +} > + > + > +static const struct samsung_usb2_common_phy exynos4x12_phys[] = { > + { > + .label = "device", > + .id = EXYNOS4x12_DEVICE, > + .power_on = exynos4x12_power_on, > + .power_off = exynos4x12_power_off, > + }, > + { > + .label = "host", > + .id = EXYNOS4x12_HOST, > + .power_on = exynos4x12_power_on, > + .power_off = exynos4x12_power_off, > + }, > + { > + .label = "hsic0", > + .id = EXYNOS4x12_HSIC0, > + .power_on = exynos4x12_power_on, > + .power_off = exynos4x12_power_off, > + }, > + { > + .label = "hsic1", > + .id = EXYNOS4x12_HSIC1, > + .power_on = exynos4x12_power_on, > + .power_off = exynos4x12_power_off, > + }, > + {}, > +}; > + > +const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config = { > + .has_mode_switch = 1, > + .num_phys = EXYNOS4x12_NUM_PHYS, > + .phys = exynos4x12_phys, > + .rate_to_clk = exynos4x12_rate_to_clk, > +}; > + > diff --git a/drivers/phy/phy-samsung-usb2.c b/drivers/phy/phy-samsung-usb2.c > new file mode 100644 > index 0000000..478f856 > --- /dev/null > +++ b/drivers/phy/phy-samsung-usb2.c > @@ -0,0 +1,223 @@ > +/* > + * Samsung SoC USB 1.1/2.0 PHY driver > + * > + * Copyright (C) 2013 Samsung Electronics Co., Ltd. > + * Author: Kamil Debski <k.debski@samsung.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/clk.h> > +#include <linux/mfd/syscon.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_address.h> > +#include <linux/phy/phy.h> > +#include <linux/platform_device.h> > +#include <linux/spinlock.h> > +#include "phy-samsung-usb2.h" > + > +static int samsung_usb2_phy_power_on(struct phy *phy) > +{ > + struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy); > + struct samsung_usb2_phy_driver *drv = inst->drv; > + int ret; > + > + dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n", > + inst->cfg->label); > + ret = clk_prepare_enable(drv->clk); > + if (ret) > + goto err_main_clk; > + ret = clk_prepare_enable(drv->ref_clk); > + if (ret) > + goto err_instance_clk; > + if (inst->cfg->power_on) { > + spin_lock(&drv->lock); > + ret = inst->cfg->power_on(inst); > + spin_unlock(&drv->lock); > + } > + > + return 0; > + > +err_instance_clk: > + clk_disable_unprepare(drv->clk); > +err_main_clk: > + return ret; > +} > + > +static int samsung_usb2_phy_power_off(struct phy *phy) > +{ > + struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy); > + struct samsung_usb2_phy_driver *drv = inst->drv; > + int ret = 0; > + > + dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n", > + inst->cfg->label); > + if (inst->cfg->power_off) { > + spin_lock(&drv->lock); > + ret = inst->cfg->power_off(inst); > + spin_unlock(&drv->lock); > + } > + clk_disable_unprepare(drv->ref_clk); > + clk_disable_unprepare(drv->clk); > + return ret; > +} > + > +static struct phy_ops samsung_usb2_phy_ops = { > + .power_on = samsung_usb2_phy_power_on, > + .power_off = samsung_usb2_phy_power_off, > + .owner = THIS_MODULE, > +}; > + > +static struct phy *samsung_usb2_phy_xlate(struct device *dev, > + struct of_phandle_args *args) > +{ > + struct samsung_usb2_phy_driver *drv; > + > + drv = dev_get_drvdata(dev); > + if (!drv) > + return ERR_PTR(-EINVAL); > + > + if (WARN_ON(args->args[0] >= drv->cfg->num_phys)) > + return ERR_PTR(-ENODEV); > + > + return drv->instances[args->args[0]].phy; > +} > + > +static const struct of_device_id samsung_usb2_phy_of_match[] = { > +#ifdef CONFIG_PHY_EXYNOS4210_USB2 > + { > + .compatible = "samsung,exynos4210-usb2-phy", > + .data = &exynos4210_usb2_phy_config, > + }, > +#endif > +#ifdef CONFIG_PHY_EXYNOS4X12_USB2 > + { > + .compatible = "samsung,exynos4x12-usb2-phy", > + .data = &exynos4x12_usb2_phy_config, > + }, > +#endif > + { }, > +}; > + > +static int samsung_usb2_phy_probe(struct platform_device *pdev) > +{ > + const struct of_device_id *match; > + const struct samsung_usb2_phy_config *cfg; > + struct device *dev = &pdev->dev; > + struct phy_provider *phy_provider; > + struct resource *mem; > + struct samsung_usb2_phy_driver *drv; > + int i, ret; > + > + if (!pdev->dev.of_node) { > + dev_err(dev, "This driver is required to be instantiated from device tree\n"); > + return -EINVAL; > + } > + > + match = of_match_node(samsung_usb2_phy_of_match, pdev->dev.of_node); > + if (!match) { > + dev_err(dev, "of_match_node() failed\n"); > + return -EINVAL; > + } > + cfg = match->data; > + > + drv = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) + > + cfg->num_phys * sizeof(struct samsung_usb2_phy_instance), > + GFP_KERNEL); > + if (!drv) > + return -ENOMEM; > + > + dev_set_drvdata(dev, drv); > + spin_lock_init(&drv->lock); > + > + drv->cfg = cfg; > + drv->dev = dev; > + > + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + drv->reg_phy = devm_ioremap_resource(dev, mem); > + if (IS_ERR(drv->reg_phy)) { > + dev_err(dev, "Failed to map register memory (phy)\n"); > + return PTR_ERR(drv->reg_phy); > + } > + > + drv->reg_pmu = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, > + "samsung,pmureg-phandle"); > + if (IS_ERR(drv->reg_pmu)) { > + dev_err(dev, "Failed to map PMU registers (via syscon)\n"); > + return PTR_ERR(drv->reg_pmu); > + } > + > + if (drv->cfg->has_mode_switch) { > + drv->reg_sys = syscon_regmap_lookup_by_phandle( > + pdev->dev.of_node, "samsung,sysreg-phandle"); > + if (IS_ERR(drv->reg_sys)) { > + dev_err(dev, "Failed to map system registers (via syscon)\n"); > + return PTR_ERR(drv->reg_sys); > + } > + } > + > + drv->clk = devm_clk_get(dev, "phy"); > + if (IS_ERR(drv->clk)) { > + dev_err(dev, "Failed to get clock of phy controller\n"); > + return PTR_ERR(drv->clk); > + } > + > + drv->ref_clk = devm_clk_get(dev, "ref"); > + if (IS_ERR(drv->ref_clk)) { > + dev_err(dev, "Failed to get reference clock for the phy controller\n"); > + return PTR_ERR(drv->ref_clk); > + } > + > + drv->ref_rate = clk_get_rate(drv->ref_clk); > + if (drv->cfg->rate_to_clk) { > + ret = drv->cfg->rate_to_clk(drv->ref_rate, &drv->ref_reg_val); > + if (ret) > + return ret; > + } > + > + for (i = 0; i < drv->cfg->num_phys; i++) { > + char *label = drv->cfg->phys[i].label; > + struct samsung_usb2_phy_instance *p = &drv->instances[i]; > + > + dev_dbg(dev, "Creating phy \"%s\"\n", label); > + p->phy = devm_phy_create(dev, &samsung_usb2_phy_ops, NULL); > + if (IS_ERR(p->phy)) { > + dev_err(drv->dev, "Failed to create usb2_phy \"%s\"\n", > + label); > + return PTR_ERR(p->phy); > + } > + > + p->cfg = &drv->cfg->phys[i]; > + p->drv = drv; > + phy_set_bus_width(p->phy, 8); > + phy_set_drvdata(p->phy, p); > + } > + > + phy_provider = devm_of_phy_provider_register(dev, > + samsung_usb2_phy_xlate); > + if (IS_ERR(phy_provider)) { > + dev_err(drv->dev, "Failed to register phy provider\n"); > + return PTR_ERR(phy_provider); > + } > + > + return 0; > +} > + > +static struct platform_driver samsung_usb2_phy_driver = { > + .probe = samsung_usb2_phy_probe, > + .driver = { > + .of_match_table = samsung_usb2_phy_of_match, > + .name = "samsung-usb2-phy", > + .owner = THIS_MODULE, > + } > +}; > + > +module_platform_driver(samsung_usb2_phy_driver); > +MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC USB PHY driver"); > +MODULE_AUTHOR("Kamil Debski <k.debski@samsung.com>"); > +MODULE_LICENSE("GPL v2"); > +MODULE_ALIAS("platform:samsung-usb2-phy"); > + > diff --git a/drivers/phy/phy-samsung-usb2.h b/drivers/phy/phy-samsung-usb2.h > new file mode 100644 > index 0000000..c004e90 > --- /dev/null > +++ b/drivers/phy/phy-samsung-usb2.h > @@ -0,0 +1,67 @@ > +/* > + * Samsung SoC USB 1.1/2.0 PHY driver > + * > + * Copyright (C) 2013 Samsung Electronics Co., Ltd. > + * Author: Kamil Debski <k.debski@samsung.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#ifndef _PHY_EXYNOS_USB2_H > +#define _PHY_EXYNOS_USB2_H > + > +#include <linux/clk.h> > +#include <linux/phy/phy.h> > +#include <linux/device.h> > +#include <linux/regmap.h> > +#include <linux/spinlock.h> > + > +#define KHZ 1000 > +#define MHZ (KHZ * KHZ) > + > +struct samsung_usb2_phy_driver; > +struct samsung_usb2_phy_instance; > +struct samsung_usb2_phy_config; > + > +struct samsung_usb2_phy_instance { > + const struct samsung_usb2_common_phy *cfg; > + struct phy *phy; > + struct samsung_usb2_phy_driver *drv; > + bool enabled; > +}; > + > +struct samsung_usb2_phy_driver { > + const struct samsung_usb2_phy_config *cfg; > + struct clk *clk; > + struct clk *ref_clk; > + unsigned long ref_rate; > + u32 ref_reg_val; > + struct device *dev; > + void __iomem *reg_phy; > + struct regmap *reg_pmu; > + struct regmap *reg_sys; > + spinlock_t lock; > + struct samsung_usb2_phy_instance instances[0]; > +}; > + > +struct samsung_usb2_common_phy { > + int (*power_on)(struct samsung_usb2_phy_instance *); > + int (*power_off)(struct samsung_usb2_phy_instance *); > + unsigned int id; > + char *label; > +}; > + > + > +struct samsung_usb2_phy_config { > + const struct samsung_usb2_common_phy *phys; > + int (*rate_to_clk)(unsigned long, u32 *); > + unsigned int num_phys; > + bool has_mode_switch; > +}; > + > +extern const struct samsung_usb2_phy_config exynos4210_usb2_phy_config; > +extern const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config; > +#endif > + > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index c0fccaa..bf955ab 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -20,3 +20,56 @@ Required properties: - compatible : should be "samsung,exynos5250-dp-video-phy"; - reg : offset and length of the Display Port PHY register set; - #phy-cells : from the generic PHY bindings, must be 0; + +Samsung S5P/EXYNOS SoC series USB PHY +------------------------------------------------- + +Required properties: +- compatible : should be one of the listed compatibles: + - "samsung,exynos4210-usb2-phy" + - "samsung,exynos4x12-usb2-phy" +- reg : a list of registers used by phy driver + - first and obligatory is the location of phy modules registers +- samsung,sysreg-phandle - handle to syscon used to control the system registers +- samsung,pmureg-phandle - handle to syscon used to control PMU registers +- #phy-cells : from the generic phy bindings, must be 1; +- clocks and clock-names: + - the "phy" clock is required by the phy module, used as a gate + - the "ref" clock is used to get the rate of the clock provided to the + PHY module + +The first phandle argument in the PHY specifier identifies the PHY, its +meaning is compatible dependent. For the currently supported SoCs (Exynos 4210 +and Exynos 4212) it is as follows: + 0 - USB device ("device"), + 1 - USB host ("host"), + 2 - HSIC0 ("hsic0"), + 3 - HSIC1 ("hsic1"), + +Exynos 4210 and Exynos 4212 use mode switching and require that mode switch +register is supplied. + +Example: + +For Exynos 4412 (compatible with Exynos 4212): + +usbphy: phy@125b0000 { + compatible = "samsung,exynos4x12-usb2-phy"; + reg = <0x125b0000 0x100>; + clocks = <&clock 305>, <&clock 2>; + clock-names = "phy", "ref"; + status = "okay"; + #phy-cells = <1>; + samsung,sysreg-phandle = <&sys_reg>; + samsung,pmureg-phandle = <&pmu_reg>; +}; + +Then the PHY can be used in other nodes such as: + +phy-consumer@12340000 { + phys = <&usbphy 2>; + phy-names = "phy"; +}; + +Refer to DT bindings documentation of particular PHY consumer devices for more +information about required PHYs and the way of specification. diff --git a/Documentation/phy/samsung-usb2.txt b/Documentation/phy/samsung-usb2.txt new file mode 100644 index 0000000..0c8e260 --- /dev/null +++ b/Documentation/phy/samsung-usb2.txt @@ -0,0 +1,134 @@ +.------------------------------------------------------------------------------+ +| Samsung USB 2.0 PHY adaptation layer | ++-----------------------------------------------------------------------------+' + +| 1. Description ++---------------- + +The architecture of the USB 2.0 PHY module in Samsung SoCs is similar +among many SoCs. In spite of the similarities it proved difficult to +create a one driver that would fit all these PHY controllers. Often +the differences were minor and were found in particular bits of the +registers of the PHY. In some rare cases the order of register writes or +the PHY powering up process had to be altered. This adaptation layer is +a compromise between having separate drivers and having a single driver +with added support for many special cases. + +| 2. Files description ++---------------------- + +- phy-samsung-usb2.c + This is the main file of the adaptation layer. This file contains + the probe function and provides two callbacks to the Generic PHY + Framework. This two callbacks are used to power on and power off the + phy. They carry out the common work that has to be done on all version + of the PHY module. Depending on which SoC was chosen they execute SoC + specific callbacks. The specific SoC version is selected by choosing + the appropriate compatible string. In addition, this file contains + struct of_device_id definitions for particular SoCs. + +- phy-samsung-usb2.h + This is the include file. It declares the structures used by this + driver. In addition it should contain extern declarations for + structures that describe particular SoCs. + +| 3. Supporting SoCs ++-------------------- + +To support a new SoC a new file should be added to the drivers/phy +directory. Each SoC's configuration is stored in an instance of the +struct samsung_usb2_phy_config. + +struct samsung_usb2_phy_config { + const struct samsung_usb2_common_phy *phys; + unsigned int num_phys; + bool has_mode_switch; +}; + +The num_phys is the number of phys handled by the driver. *phys is an +array that contains the configuration for each phy. The has_mode_switch +property is a boolean flag that determines whether the SoC has USB host +and device on a single pair of pins. If so, a special register has to +be modified to change the internal routing of these pins between a USB +device or host module. + +For example the configuration for Exynos 4210 is following: + +const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = { + .has_mode_switch = 0, + .num_phys = EXYNOS4210_NUM_PHYS, + .phys = exynos4210_phys, + .rate_to_clk = exynos4210_rate_to_clk, +} + +- int (*rate_to_clk)(unsigned long, u32 *) + The rate_to_clk callback is to convert the rate of the clock + used as the reference clock for the PHY module to the value + that should be written in the hardware register. + +The exynos4210_phys configuration array is as follows: + +static const struct samsung_usb2_common_phy exynos4210_phys[] = { + { + .label = "device", + .id = EXYNOS4210_DEVICE, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + { + .label = "host", + .id = EXYNOS4210_HOST, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + { + .label = "hsic0", + .id = EXYNOS4210_HSIC0, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + { + .label = "hsic1", + .id = EXYNOS4210_HSIC1, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + {}, +}; + +- int (*power_on)(struct samsung_usb2_phy_instance *); +- int (*power_off)(struct samsung_usb2_phy_instance *); + These two callbacks are used to power on and power off the phy + by modifying appropriate registers. + +Final change to the driver is adding appropriate compatible value to the +phy-samsung-usb2.c file. In case of Exynos 4210 the following lines were +added to the struct of_device_id samsung_usb2_phy_of_match[] array: + +#ifdef CONFIG_PHY_EXYNOS4210_USB2 + { + .compatible = "samsung,exynos4210-usb2-phy", + .data = &exynos4210_usb2_phy_config, + }, +#endif + +To add further flexibility to the driver the Kconfig file enables to +include support for selected SoCs in the compiled driver. The Kconfig +entry for Exynos 4210 is following: + +config PHY_EXYNOS4210_USB2 + bool "Support for Exynos 4210" + depends on PHY_SAMSUNG_USB2 + depends on CPU_EXYNOS4210 + help + Enable USB PHY support for Exynos 4210. This option requires that + Samsung USB 2.0 PHY driver is enabled and means that support for this + particular SoC is compiled in the driver. In case of Exynos 4210 four + phys are available - device, host, HSCI0 and HSCI1. + +The newly created file that supports the new SoC has to be also added to the +Makefile. In case of Exynos 4210 the added line is following: + +obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o + +After completing these steps the support for the new SoC should be ready. diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index dc1756c..fc5a44a 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -96,4 +96,33 @@ config PHY_SUN4I_USB This driver controls the entire USB PHY block, both the USB OTG parts, as well as the 2 regular USB 2 host PHYs. +config PHY_SAMSUNG_USB2 + tristate "Samsung USB 2.0 PHY driver" + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the Samsung USB 2.0 PHY driver for Samsung + SoCs. This driver provides the interface for USB 2.0 PHY. Support for + particular SoCs has to be enabled in addition to this driver. Number + and type of supported phys depends on the SoC. + +config PHY_EXYNOS4210_USB2 + bool "Support for Exynos 4210" + depends on PHY_SAMSUNG_USB2 + depends on CPU_EXYNOS4210 + help + Enable USB PHY support for Exynos 4210. This option requires that + Samsung USB 2.0 PHY driver is enabled and means that support for this + particular SoC is compiled in the driver. In case of Exynos 4210 four + phys are available - device, host, HSIC0 and HSIC1. + +config PHY_EXYNOS4X12_USB2 + bool "Support for Exynos 4x12" + depends on PHY_SAMSUNG_USB2 + depends on (SOC_EXYNOS4212 || SOC_EXYNOS4412) + help + Enable USB PHY support for Exynos 4x12. This option requires that + Samsung USB 2.0 PHY driver is enabled and means that support for this + particular SoC is compiled in the driver. In case of Exynos 4x12 four + phys are available - device, host, HSIC0 and HSIC1. endmenu diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index 5d0b59e..0ea36ff 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -11,3 +11,6 @@ obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o +obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-samsung-usb2.o +obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o +obj-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o diff --git a/drivers/phy/phy-exynos4210-usb2.c b/drivers/phy/phy-exynos4210-usb2.c new file mode 100644 index 0000000..9970e81 --- /dev/null +++ b/drivers/phy/phy-exynos4210-usb2.c @@ -0,0 +1,262 @@ +/* + * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4210 support + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Author: Kamil Debski <k.debski@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> +#include "phy-samsung-usb2.h" + +/* Exynos USB PHY registers */ + +/* PHY power control */ +#define EXYNOS_4210_UPHYPWR 0x0 + +#define EXYNOS_4210_UPHYPWR_PHY0_SUSPEND BIT(0) +#define EXYNOS_4210_UPHYPWR_PHY0_PWR BIT(3) +#define EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR BIT(4) +#define EXYNOS_4210_UPHYPWR_PHY0_SLEEP BIT(5) +#define EXYNOS_4210_UPHYPWR_PHY0 ( \ + EXYNOS_4210_UPHYPWR_PHY0_SUSPEND | \ + EXYNOS_4210_UPHYPWR_PHY0_PWR | \ + EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR | \ + EXYNOS_4210_UPHYPWR_PHY0_SLEEP) + +#define EXYNOS_4210_UPHYPWR_PHY1_SUSPEND BIT(6) +#define EXYNOS_4210_UPHYPWR_PHY1_PWR BIT(7) +#define EXYNOS_4210_UPHYPWR_PHY1_SLEEP BIT(8) +#define EXYNOS_4210_UPHYPWR_PHY1 ( \ + EXYNOS_4210_UPHYPWR_PHY1_SUSPEND | \ + EXYNOS_4210_UPHYPWR_PHY1_PWR | \ + EXYNOS_4210_UPHYPWR_PHY1_SLEEP) + +#define EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND BIT(9) +#define EXYNOS_4210_UPHYPWR_HSIC0_SLEEP BIT(10) +#define EXYNOS_4210_UPHYPWR_HSIC0 ( \ + EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND | \ + EXYNOS_4210_UPHYPWR_HSIC0_SLEEP) + +#define EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND BIT(11) +#define EXYNOS_4210_UPHYPWR_HSIC1_SLEEP BIT(12) +#define EXYNOS_4210_UPHYPWR_HSIC1 ( \ + EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND | \ + EXYNOS_4210_UPHYPWR_HSIC1_SLEEP) + +/* PHY clock control */ +#define EXYNOS_4210_UPHYCLK 0x4 + +#define EXYNOS_4210_UPHYCLK_PHYFSEL_MASK (0x3 << 0) +#define EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET 0 +#define EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ (0x0 << 0) +#define EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ (0x3 << 0) +#define EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0) + +#define EXYNOS_4210_UPHYCLK_PHY0_ID_PULLUP BIT(2) +#define EXYNOS_4210_UPHYCLK_PHY0_COMMON_ON BIT(4) +#define EXYNOS_4210_UPHYCLK_PHY1_COMMON_ON BIT(7) + +/* PHY reset control */ +#define EXYNOS_4210_UPHYRST 0x8 + +#define EXYNOS_4210_URSTCON_PHY0 BIT(0) +#define EXYNOS_4210_URSTCON_OTG_HLINK BIT(1) +#define EXYNOS_4210_URSTCON_OTG_PHYLINK BIT(2) +#define EXYNOS_4210_URSTCON_PHY1_ALL BIT(3) +#define EXYNOS_4210_URSTCON_PHY1_P0 BIT(4) +#define EXYNOS_4210_URSTCON_PHY1_P1P2 BIT(5) +#define EXYNOS_4210_URSTCON_HOST_LINK_ALL BIT(6) +#define EXYNOS_4210_URSTCON_HOST_LINK_P0 BIT(7) +#define EXYNOS_4210_URSTCON_HOST_LINK_P1 BIT(8) +#define EXYNOS_4210_URSTCON_HOST_LINK_P2 BIT(9) + +/* Isolation, configured in the power management unit */ +#define EXYNOS_4210_USB_ISOL_DEVICE_OFFSET 0x704 +#define EXYNOS_4210_USB_ISOL_DEVICE BIT(0) +#define EXYNOS_4210_USB_ISOL_HOST_OFFSET 0x708 +#define EXYNOS_4210_USB_ISOL_HOST BIT(0) + +/* USBYPHY1 Floating prevention */ +#define EXYNOS_4210_UPHY1CON 0x34 +#define EXYNOS_4210_UPHY1CON_FLOAT_PREVENTION 0x1 + +/* Mode switching SUB Device <-> Host */ +#define EXYNOS_4210_MODE_SWITCH_OFFSET 0x21c +#define EXYNOS_4210_MODE_SWITCH_MASK 1 +#define EXYNOS_4210_MODE_SWITCH_DEVICE 0 +#define EXYNOS_4210_MODE_SWITCH_HOST 1 + +enum exynos4210_phy_id { + EXYNOS4210_DEVICE, + EXYNOS4210_HOST, + EXYNOS4210_HSIC0, + EXYNOS4210_HSIC1, + EXYNOS4210_NUM_PHYS, +}; + +/* + * exynos4210_rate_to_clk() converts the supplied clock rate to the value that + * can be written to the phy register. + */ +static int exynos4210_rate_to_clk(unsigned long rate, u32 *reg) +{ + switch (rate) { + case 12 * MHZ: + *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ; + break; + case 24 * MHZ: + *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ; + break; + case 48 * MHZ: + *reg = EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ; + break; + default: + return -EINVAL; + } + + return 0; +} + +static void exynos4210_isol(struct samsung_usb2_phy_instance *inst, bool on) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + u32 offset; + u32 mask; + + switch (inst->cfg->id) { + case EXYNOS4210_DEVICE: + offset = EXYNOS_4210_USB_ISOL_DEVICE_OFFSET; + mask = EXYNOS_4210_USB_ISOL_DEVICE; + break; + case EXYNOS4210_HOST: + offset = EXYNOS_4210_USB_ISOL_HOST_OFFSET; + mask = EXYNOS_4210_USB_ISOL_HOST; + break; + default: + return; + }; + + regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask); +} + +static void exynos4210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + u32 rstbits = 0; + u32 phypwr = 0; + u32 rst; + u32 pwr; + u32 clk; + + switch (inst->cfg->id) { + case EXYNOS4210_DEVICE: + phypwr = EXYNOS_4210_UPHYPWR_PHY0; + rstbits = EXYNOS_4210_URSTCON_PHY0; + break; + case EXYNOS4210_HOST: + phypwr = EXYNOS_4210_UPHYPWR_PHY1; + rstbits = EXYNOS_4210_URSTCON_PHY1_ALL | + EXYNOS_4210_URSTCON_PHY1_P0 | + EXYNOS_4210_URSTCON_PHY1_P1P2 | + EXYNOS_4210_URSTCON_HOST_LINK_ALL | + EXYNOS_4210_URSTCON_HOST_LINK_P0; + writel(on, drv->reg_phy + EXYNOS_4210_UPHY1CON); + break; + case EXYNOS4210_HSIC0: + phypwr = EXYNOS_4210_UPHYPWR_HSIC0; + rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 | + EXYNOS_4210_URSTCON_HOST_LINK_P1; + break; + case EXYNOS4210_HSIC1: + phypwr = EXYNOS_4210_UPHYPWR_HSIC1; + rstbits = EXYNOS_4210_URSTCON_PHY1_P1P2 | + EXYNOS_4210_URSTCON_HOST_LINK_P2; + break; + }; + + if (on) { + clk = readl(drv->reg_phy + EXYNOS_4210_UPHYCLK); + clk &= ~EXYNOS_4210_UPHYCLK_PHYFSEL_MASK; + clk |= drv->ref_reg_val << EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET; + writel(clk, drv->reg_phy + EXYNOS_4210_UPHYCLK); + + pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR); + pwr &= ~phypwr; + writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR); + + rst = readl(drv->reg_phy + EXYNOS_4210_UPHYRST); + rst |= rstbits; + writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST); + udelay(10); + rst &= ~rstbits; + writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST); + /* The following delay is necessary for the reset sequence to be + * completed */ + udelay(80); + } else { + pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR); + pwr |= phypwr; + writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR); + } +} + +static int exynos4210_power_on(struct samsung_usb2_phy_instance *inst) +{ + /* Order of initialisation is important - first power then isolation */ + exynos4210_phy_pwr(inst, 1); + exynos4210_isol(inst, 0); + + return 0; +} + +static int exynos4210_power_off(struct samsung_usb2_phy_instance *inst) +{ + exynos4210_isol(inst, 1); + exynos4210_phy_pwr(inst, 0); + + return 0; +} + + +static const struct samsung_usb2_common_phy exynos4210_phys[] = { + { + .label = "device", + .id = EXYNOS4210_DEVICE, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + { + .label = "host", + .id = EXYNOS4210_HOST, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + { + .label = "hsic0", + .id = EXYNOS4210_HSIC0, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + { + .label = "hsic1", + .id = EXYNOS4210_HSIC1, + .power_on = exynos4210_power_on, + .power_off = exynos4210_power_off, + }, + {}, +}; + +const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = { + .has_mode_switch = 0, + .num_phys = EXYNOS4210_NUM_PHYS, + .phys = exynos4210_phys, + .rate_to_clk = exynos4210_rate_to_clk, +}; + diff --git a/drivers/phy/phy-exynos4x12-usb2.c b/drivers/phy/phy-exynos4x12-usb2.c new file mode 100644 index 0000000..40c90f9 --- /dev/null +++ b/drivers/phy/phy-exynos4x12-usb2.c @@ -0,0 +1,329 @@ +/* + * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4x12 support + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Author: Kamil Debski <k.debski@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> +#include "phy-samsung-usb2.h" + +/* Exynos USB PHY registers */ + +/* PHY power control */ +#define EXYNOS_4x12_UPHYPWR 0x0 + +#define EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND BIT(0) +#define EXYNOS_4x12_UPHYPWR_PHY0_PWR BIT(3) +#define EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR BIT(4) +#define EXYNOS_4x12_UPHYPWR_PHY0_SLEEP BIT(5) +#define EXYNOS_4x12_UPHYPWR_PHY0 ( \ + EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND | \ + EXYNOS_4x12_UPHYPWR_PHY0_PWR | \ + EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR | \ + EXYNOS_4x12_UPHYPWR_PHY0_SLEEP) + +#define EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND BIT(6) +#define EXYNOS_4x12_UPHYPWR_PHY1_PWR BIT(7) +#define EXYNOS_4x12_UPHYPWR_PHY1_SLEEP BIT(8) +#define EXYNOS_4x12_UPHYPWR_PHY1 ( \ + EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND | \ + EXYNOS_4x12_UPHYPWR_PHY1_PWR | \ + EXYNOS_4x12_UPHYPWR_PHY1_SLEEP) + +#define EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND BIT(9) +#define EXYNOS_4x12_UPHYPWR_HSIC0_PWR BIT(10) +#define EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP BIT(11) +#define EXYNOS_4x12_UPHYPWR_HSIC0 ( \ + EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND | \ + EXYNOS_4x12_UPHYPWR_HSIC0_PWR | \ + EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP) + +#define EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND BIT(12) +#define EXYNOS_4x12_UPHYPWR_HSIC1_PWR BIT(13) +#define EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP BIT(14) +#define EXYNOS_4x12_UPHYPWR_HSIC1 ( \ + EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND | \ + EXYNOS_4x12_UPHYPWR_HSIC1_PWR | \ + EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP) + +/* PHY clock control */ +#define EXYNOS_4x12_UPHYCLK 0x4 + +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK (0x7 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET 0 +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6 (0x0 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ (0x1 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ (0x2 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2 (0x3 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ (0x4 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ (0x5 << 0) +#define EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ (0x7 << 0) + +#define EXYNOS_4x12_UPHYCLK_PHY0_ID_PULLUP BIT(3) +#define EXYNOS_4x12_UPHYCLK_PHY0_COMMON_ON BIT(4) +#define EXYNOS_4x12_UPHYCLK_PHY1_COMMON_ON BIT(7) + +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_MASK (0x7f << 10) +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_OFFSET 10 +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_12MHZ (0x24 << 10) +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_15MHZ (0x1c << 10) +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_16MHZ (0x1a << 10) +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_19MHZ2 (0x15 << 10) +#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_20MHZ (0x14 << 10) + +/* PHY reset control */ +#define EXYNOS_4x12_UPHYRST 0x8 + +#define EXYNOS_4x12_URSTCON_PHY0 BIT(0) +#define EXYNOS_4x12_URSTCON_OTG_HLINK BIT(1) +#define EXYNOS_4x12_URSTCON_OTG_PHYLINK BIT(2) +#define EXYNOS_4x12_URSTCON_HOST_PHY BIT(3) +#define EXYNOS_4x12_URSTCON_PHY1 BIT(4) +#define EXYNOS_4x12_URSTCON_HSIC0 BIT(5) +#define EXYNOS_4x12_URSTCON_HSIC1 BIT(6) +#define EXYNOS_4x12_URSTCON_HOST_LINK_ALL BIT(7) +#define EXYNOS_4x12_URSTCON_HOST_LINK_P0 BIT(8) +#define EXYNOS_4x12_URSTCON_HOST_LINK_P1 BIT(9) +#define EXYNOS_4x12_URSTCON_HOST_LINK_P2 BIT(10) + +/* Isolation, configured in the power management unit */ +#define EXYNOS_4x12_USB_ISOL_OFFSET 0x704 +#define EXYNOS_4x12_USB_ISOL_OTG BIT(0) +#define EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET 0x708 +#define EXYNOS_4x12_USB_ISOL_HSIC0 BIT(0) +#define EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET 0x70c +#define EXYNOS_4x12_USB_ISOL_HSIC1 BIT(0) + +/* Mode switching SUB Device <-> Host */ +#define EXYNOS_4x12_MODE_SWITCH_OFFSET 0x21c +#define EXYNOS_4x12_MODE_SWITCH_MASK 1 +#define EXYNOS_4x12_MODE_SWITCH_DEVICE 0 +#define EXYNOS_4x12_MODE_SWITCH_HOST 1 + +enum exynos4x12_phy_id { + EXYNOS4x12_DEVICE, + EXYNOS4x12_HOST, + EXYNOS4x12_HSIC0, + EXYNOS4x12_HSIC1, + EXYNOS4x12_NUM_PHYS, +}; + +/* + * exynos4x12_rate_to_clk() converts the supplied clock rate to the value that + * can be written to the phy register. + */ +static int exynos4x12_rate_to_clk(unsigned long rate, u32 *reg) +{ + /* EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK */ + + switch (rate) { + case 9600 * KHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6; + break; + case 10 * MHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ; + break; + case 12 * MHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ; + break; + case 19200 * KHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2; + break; + case 20 * MHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ; + break; + case 24 * MHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ; + break; + case 50 * MHZ: + *reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ; + break; + default: + return -EINVAL; + } + + return 0; +} + +static void exynos4x12_isol(struct samsung_usb2_phy_instance *inst, bool on) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + u32 offset; + u32 mask; + + switch (inst->cfg->id) { + case EXYNOS4x12_DEVICE: + case EXYNOS4x12_HOST: + offset = EXYNOS_4x12_USB_ISOL_OFFSET; + mask = EXYNOS_4x12_USB_ISOL_OTG; + break; + case EXYNOS4x12_HSIC0: + offset = EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET; + mask = EXYNOS_4x12_USB_ISOL_HSIC0; + break; + case EXYNOS4x12_HSIC1: + offset = EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET; + mask = EXYNOS_4x12_USB_ISOL_HSIC1; + break; + default: + return; + }; + + regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask); +} + +static void exynos4x12_setup_clk(struct samsung_usb2_phy_instance *inst) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + u32 clk; + + clk = readl(drv->reg_phy + EXYNOS_4x12_UPHYCLK); + clk &= ~EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK; + clk |= drv->ref_reg_val << EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET; + writel(clk, drv->reg_phy + EXYNOS_4x12_UPHYCLK); +} + +static void exynos4x12_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + u32 rstbits = 0; + u32 phypwr = 0; + u32 rst; + u32 pwr; + u32 mode = 0; + u32 switch_mode = 0; + + switch (inst->cfg->id) { + case EXYNOS4x12_DEVICE: + phypwr = EXYNOS_4x12_UPHYPWR_PHY0; + rstbits = EXYNOS_4x12_URSTCON_PHY0; + mode = EXYNOS_4x12_MODE_SWITCH_DEVICE; + switch_mode = 1; + break; + case EXYNOS4x12_HOST: + phypwr = EXYNOS_4x12_UPHYPWR_PHY1; + rstbits = EXYNOS_4x12_URSTCON_HOST_PHY; + mode = EXYNOS_4x12_MODE_SWITCH_HOST; + switch_mode = 1; + break; + case EXYNOS4x12_HSIC0: + phypwr = EXYNOS_4x12_UPHYPWR_HSIC0; + rstbits = EXYNOS_4x12_URSTCON_HSIC1 | + EXYNOS_4x12_URSTCON_HOST_LINK_P0 | + EXYNOS_4x12_URSTCON_HOST_PHY; + break; + case EXYNOS4x12_HSIC1: + phypwr = EXYNOS_4x12_UPHYPWR_HSIC1; + rstbits = EXYNOS_4x12_URSTCON_HSIC1 | + EXYNOS_4x12_URSTCON_HOST_LINK_P1; + break; + }; + + if (on) { + if (switch_mode) + regmap_update_bits(drv->reg_sys, + EXYNOS_4x12_MODE_SWITCH_OFFSET, + EXYNOS_4x12_MODE_SWITCH_MASK, mode); + + pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR); + pwr &= ~phypwr; + writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR); + + rst = readl(drv->reg_phy + EXYNOS_4x12_UPHYRST); + rst |= rstbits; + writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST); + udelay(10); + rst &= ~rstbits; + writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST); + /* The following delay is necessary for the reset sequence to be + * completed */ + udelay(80); + } else { + pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR); + pwr |= phypwr; + writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR); + } +} + +static int exynos4x12_power_on(struct samsung_usb2_phy_instance *inst) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + + inst->enabled = 1; + exynos4x12_setup_clk(inst); + exynos4x12_phy_pwr(inst, 1); + exynos4x12_isol(inst, 0); + + /* Power on the device, as it is necessary for HSIC to work */ + if (inst->cfg->id == EXYNOS4x12_HSIC0) { + struct samsung_usb2_phy_instance *device = + &drv->instances[EXYNOS4x12_DEVICE]; + exynos4x12_phy_pwr(device, 1); + exynos4x12_isol(device, 0); + } + + return 0; +} + +static int exynos4x12_power_off(struct samsung_usb2_phy_instance *inst) +{ + struct samsung_usb2_phy_driver *drv = inst->drv; + struct samsung_usb2_phy_instance *device = + &drv->instances[EXYNOS4x12_DEVICE]; + + inst->enabled = 0; + exynos4x12_isol(inst, 1); + exynos4x12_phy_pwr(inst, 0); + + if (inst->cfg->id == EXYNOS4x12_HSIC0 && !device->enabled) { + exynos4x12_isol(device, 1); + exynos4x12_phy_pwr(device, 0); + } + + return 0; +} + + +static const struct samsung_usb2_common_phy exynos4x12_phys[] = { + { + .label = "device", + .id = EXYNOS4x12_DEVICE, + .power_on = exynos4x12_power_on, + .power_off = exynos4x12_power_off, + }, + { + .label = "host", + .id = EXYNOS4x12_HOST, + .power_on = exynos4x12_power_on, + .power_off = exynos4x12_power_off, + }, + { + .label = "hsic0", + .id = EXYNOS4x12_HSIC0, + .power_on = exynos4x12_power_on, + .power_off = exynos4x12_power_off, + }, + { + .label = "hsic1", + .id = EXYNOS4x12_HSIC1, + .power_on = exynos4x12_power_on, + .power_off = exynos4x12_power_off, + }, + {}, +}; + +const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config = { + .has_mode_switch = 1, + .num_phys = EXYNOS4x12_NUM_PHYS, + .phys = exynos4x12_phys, + .rate_to_clk = exynos4x12_rate_to_clk, +}; + diff --git a/drivers/phy/phy-samsung-usb2.c b/drivers/phy/phy-samsung-usb2.c new file mode 100644 index 0000000..478f856 --- /dev/null +++ b/drivers/phy/phy-samsung-usb2.c @@ -0,0 +1,223 @@ +/* + * Samsung SoC USB 1.1/2.0 PHY driver + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Author: Kamil Debski <k.debski@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/spinlock.h> +#include "phy-samsung-usb2.h" + +static int samsung_usb2_phy_power_on(struct phy *phy) +{ + struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy); + struct samsung_usb2_phy_driver *drv = inst->drv; + int ret; + + dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n", + inst->cfg->label); + ret = clk_prepare_enable(drv->clk); + if (ret) + goto err_main_clk; + ret = clk_prepare_enable(drv->ref_clk); + if (ret) + goto err_instance_clk; + if (inst->cfg->power_on) { + spin_lock(&drv->lock); + ret = inst->cfg->power_on(inst); + spin_unlock(&drv->lock); + } + + return 0; + +err_instance_clk: + clk_disable_unprepare(drv->clk); +err_main_clk: + return ret; +} + +static int samsung_usb2_phy_power_off(struct phy *phy) +{ + struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy); + struct samsung_usb2_phy_driver *drv = inst->drv; + int ret = 0; + + dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n", + inst->cfg->label); + if (inst->cfg->power_off) { + spin_lock(&drv->lock); + ret = inst->cfg->power_off(inst); + spin_unlock(&drv->lock); + } + clk_disable_unprepare(drv->ref_clk); + clk_disable_unprepare(drv->clk); + return ret; +} + +static struct phy_ops samsung_usb2_phy_ops = { + .power_on = samsung_usb2_phy_power_on, + .power_off = samsung_usb2_phy_power_off, + .owner = THIS_MODULE, +}; + +static struct phy *samsung_usb2_phy_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct samsung_usb2_phy_driver *drv; + + drv = dev_get_drvdata(dev); + if (!drv) + return ERR_PTR(-EINVAL); + + if (WARN_ON(args->args[0] >= drv->cfg->num_phys)) + return ERR_PTR(-ENODEV); + + return drv->instances[args->args[0]].phy; +} + +static const struct of_device_id samsung_usb2_phy_of_match[] = { +#ifdef CONFIG_PHY_EXYNOS4210_USB2 + { + .compatible = "samsung,exynos4210-usb2-phy", + .data = &exynos4210_usb2_phy_config, + }, +#endif +#ifdef CONFIG_PHY_EXYNOS4X12_USB2 + { + .compatible = "samsung,exynos4x12-usb2-phy", + .data = &exynos4x12_usb2_phy_config, + }, +#endif + { }, +}; + +static int samsung_usb2_phy_probe(struct platform_device *pdev) +{ + const struct of_device_id *match; + const struct samsung_usb2_phy_config *cfg; + struct device *dev = &pdev->dev; + struct phy_provider *phy_provider; + struct resource *mem; + struct samsung_usb2_phy_driver *drv; + int i, ret; + + if (!pdev->dev.of_node) { + dev_err(dev, "This driver is required to be instantiated from device tree\n"); + return -EINVAL; + } + + match = of_match_node(samsung_usb2_phy_of_match, pdev->dev.of_node); + if (!match) { + dev_err(dev, "of_match_node() failed\n"); + return -EINVAL; + } + cfg = match->data; + + drv = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) + + cfg->num_phys * sizeof(struct samsung_usb2_phy_instance), + GFP_KERNEL); + if (!drv) + return -ENOMEM; + + dev_set_drvdata(dev, drv); + spin_lock_init(&drv->lock); + + drv->cfg = cfg; + drv->dev = dev; + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + drv->reg_phy = devm_ioremap_resource(dev, mem); + if (IS_ERR(drv->reg_phy)) { + dev_err(dev, "Failed to map register memory (phy)\n"); + return PTR_ERR(drv->reg_phy); + } + + drv->reg_pmu = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, + "samsung,pmureg-phandle"); + if (IS_ERR(drv->reg_pmu)) { + dev_err(dev, "Failed to map PMU registers (via syscon)\n"); + return PTR_ERR(drv->reg_pmu); + } + + if (drv->cfg->has_mode_switch) { + drv->reg_sys = syscon_regmap_lookup_by_phandle( + pdev->dev.of_node, "samsung,sysreg-phandle"); + if (IS_ERR(drv->reg_sys)) { + dev_err(dev, "Failed to map system registers (via syscon)\n"); + return PTR_ERR(drv->reg_sys); + } + } + + drv->clk = devm_clk_get(dev, "phy"); + if (IS_ERR(drv->clk)) { + dev_err(dev, "Failed to get clock of phy controller\n"); + return PTR_ERR(drv->clk); + } + + drv->ref_clk = devm_clk_get(dev, "ref"); + if (IS_ERR(drv->ref_clk)) { + dev_err(dev, "Failed to get reference clock for the phy controller\n"); + return PTR_ERR(drv->ref_clk); + } + + drv->ref_rate = clk_get_rate(drv->ref_clk); + if (drv->cfg->rate_to_clk) { + ret = drv->cfg->rate_to_clk(drv->ref_rate, &drv->ref_reg_val); + if (ret) + return ret; + } + + for (i = 0; i < drv->cfg->num_phys; i++) { + char *label = drv->cfg->phys[i].label; + struct samsung_usb2_phy_instance *p = &drv->instances[i]; + + dev_dbg(dev, "Creating phy \"%s\"\n", label); + p->phy = devm_phy_create(dev, &samsung_usb2_phy_ops, NULL); + if (IS_ERR(p->phy)) { + dev_err(drv->dev, "Failed to create usb2_phy \"%s\"\n", + label); + return PTR_ERR(p->phy); + } + + p->cfg = &drv->cfg->phys[i]; + p->drv = drv; + phy_set_bus_width(p->phy, 8); + phy_set_drvdata(p->phy, p); + } + + phy_provider = devm_of_phy_provider_register(dev, + samsung_usb2_phy_xlate); + if (IS_ERR(phy_provider)) { + dev_err(drv->dev, "Failed to register phy provider\n"); + return PTR_ERR(phy_provider); + } + + return 0; +} + +static struct platform_driver samsung_usb2_phy_driver = { + .probe = samsung_usb2_phy_probe, + .driver = { + .of_match_table = samsung_usb2_phy_of_match, + .name = "samsung-usb2-phy", + .owner = THIS_MODULE, + } +}; + +module_platform_driver(samsung_usb2_phy_driver); +MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC USB PHY driver"); +MODULE_AUTHOR("Kamil Debski <k.debski@samsung.com>"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:samsung-usb2-phy"); + diff --git a/drivers/phy/phy-samsung-usb2.h b/drivers/phy/phy-samsung-usb2.h new file mode 100644 index 0000000..c004e90 --- /dev/null +++ b/drivers/phy/phy-samsung-usb2.h @@ -0,0 +1,67 @@ +/* + * Samsung SoC USB 1.1/2.0 PHY driver + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Author: Kamil Debski <k.debski@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef _PHY_EXYNOS_USB2_H +#define _PHY_EXYNOS_USB2_H + +#include <linux/clk.h> +#include <linux/phy/phy.h> +#include <linux/device.h> +#include <linux/regmap.h> +#include <linux/spinlock.h> + +#define KHZ 1000 +#define MHZ (KHZ * KHZ) + +struct samsung_usb2_phy_driver; +struct samsung_usb2_phy_instance; +struct samsung_usb2_phy_config; + +struct samsung_usb2_phy_instance { + const struct samsung_usb2_common_phy *cfg; + struct phy *phy; + struct samsung_usb2_phy_driver *drv; + bool enabled; +}; + +struct samsung_usb2_phy_driver { + const struct samsung_usb2_phy_config *cfg; + struct clk *clk; + struct clk *ref_clk; + unsigned long ref_rate; + u32 ref_reg_val; + struct device *dev; + void __iomem *reg_phy; + struct regmap *reg_pmu; + struct regmap *reg_sys; + spinlock_t lock; + struct samsung_usb2_phy_instance instances[0]; +}; + +struct samsung_usb2_common_phy { + int (*power_on)(struct samsung_usb2_phy_instance *); + int (*power_off)(struct samsung_usb2_phy_instance *); + unsigned int id; + char *label; +}; + + +struct samsung_usb2_phy_config { + const struct samsung_usb2_common_phy *phys; + int (*rate_to_clk)(unsigned long, u32 *); + unsigned int num_phys; + bool has_mode_switch; +}; + +extern const struct samsung_usb2_phy_config exynos4210_usb2_phy_config; +extern const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config; +#endif +
Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic PHY framework. The driver includes support for the Exynos 4x10 and 4x12 SoC families. Signed-off-by: Kamil Debski <k.debski@samsung.com> --- .../devicetree/bindings/phy/samsung-phy.txt | 53 ++++ Documentation/phy/samsung-usb2.txt | 134 ++++++++ drivers/phy/Kconfig | 29 ++ drivers/phy/Makefile | 3 + drivers/phy/phy-exynos4210-usb2.c | 262 ++++++++++++++++ drivers/phy/phy-exynos4x12-usb2.c | 329 ++++++++++++++++++++ drivers/phy/phy-samsung-usb2.c | 223 +++++++++++++ drivers/phy/phy-samsung-usb2.h | 67 ++++ 8 files changed, 1100 insertions(+) create mode 100644 Documentation/phy/samsung-usb2.txt create mode 100644 drivers/phy/phy-exynos4210-usb2.c create mode 100644 drivers/phy/phy-exynos4x12-usb2.c create mode 100644 drivers/phy/phy-samsung-usb2.c create mode 100644 drivers/phy/phy-samsung-usb2.h