diff mbox

[v3,04/15] ARM: dts: samsung-fimd: add LCD I80 interface specific properties

Message ID 1401686571-22148-5-git-send-email-yj44.cho@samsung.com (mailing list archive)
State New, archived
Headers show

Commit Message

YoungJun Cho June 2, 2014, 5:22 a.m. UTC 
In case of using MIPI DSI based I80 interface panel,
the relevant registers should be set.
So this patch adds relevant DT bindings.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 .../devicetree/bindings/video/samsung-fimd.txt     |   28 ++++++++++++++++++++
 1 file changed, 28 insertions(+)
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt
index 2dad41b..59ff61e 100644
--- a/Documentation/devicetree/bindings/video/samsung-fimd.txt
+++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt
@@ -44,6 +44,34 @@  Optional Properties:
 - display-timings: timing settings for FIMD, as described in document [1].
 		Can be used in case timings cannot be provided otherwise
 		or to override timings provided by the panel.
+- samsung,sysreg: handle to syscon used to control the system registers
+- i80-if-timings: timing configuration for lcd i80 interface support.
+  - cs-setup: clock cycles for the active period of address signal is enabled
+              until chip select is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-setup: clock cycles for the active period of CS signal is enabled until
+              write signal is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-active: clock cycles for the active period of CS is enabled.
+               If not specified, the default value(1) will be used.
+  - wr-hold: clock cycles for the active period of CS is disabled until write
+             signal is disabled.
+             If not specified, the default value(0) will be used.
+
+  The parameters are defined as:
+
+    VCLK(internal)  __|¯¯¯¯¯¯|_____|¯¯¯¯¯¯|_____|¯¯¯¯¯¯|_____|¯¯¯¯¯¯|_____|¯¯
+                      :            :            :            :            :
+    Address Output  --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
+                      | cs-setup+1 |            :            :            :
+                      |<---------->|            :            :            :
+    Chip Select     ¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯|____________:____________:____________|¯¯
+                                   | wr-setup+1 |            | wr-hold+1  |
+                                   |<---------->|            |<---------->|
+    Write Enable    ¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯|____________|¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
+                                                | wr-active+1|
+                                                |<---------->|
+    Video Data      ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
 
 The device node can contain 'port' child nodes according to the bindings defined
 in [2]. The following are properties specific to those nodes: