@@ -66,7 +66,9 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
exynos4210-trats.dtb \
exynos4210-universal_c210.dtb \
+ exynos4412-odroidu3.dtb \
exynos4412-odroidx.dtb \
+ exynos4412-odroidx2.dtb \
exynos4412-origen.dtb \
exynos4412-smdk4412.dtb \
exynos4412-tiny4412.dtb \
new file mode 100644
@@ -0,0 +1,319 @@
+/*
+ * Common definition for Hardkernel's Exynos4412 based ODROID-X/X2/U2/U3 boards
+ * device tree source
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "exynos4412.dtsi"
+
+/ {
+ firmware@0204F000 {
+ compatible = "samsung,secure-firmware";
+ reg = <0x0204F000 0x1000>;
+ };
+
+ mmc@12550000 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo20_reg &buck8_reg>;
+ status = "okay";
+
+ num-slots = <1>;
+ supports-highspeed;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <8>;
+ };
+ };
+
+ watchdog@10060000 {
+ status = "okay";
+ };
+
+ rtc@10070000 {
+ status = "okay";
+ };
+
+ g2d@10800000 {
+ status = "okay";
+ };
+
+ camera {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <>;
+
+ fimc_0: fimc@11800000 {
+ status = "okay";
+ };
+
+ fimc_1: fimc@11810000 {
+ status = "okay";
+ };
+
+ fimc_2: fimc@11820000 {
+ status = "okay";
+ };
+
+ fimc_3: fimc@11830000 {
+ status = "okay";
+ };
+ };
+
+ sdhci@12530000 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo4_reg &ldo21_reg>;
+ status = "okay";
+ };
+
+ serial@13800000 {
+ status = "okay";
+ };
+
+ serial@13810000 {
+ status = "okay";
+ };
+
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
+ };
+
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ i2c@13860000 {
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ usb3503: usb3503@08 {
+ compatible = "smsc,usb3503";
+ reg = <0x08>;
+
+ intn-gpios = <&gpx3 0 0>;
+ connect-gpios = <&gpx3 4 0>;
+ reset-gpios = <&gpx3 5 0>;
+ initial-mode = <1>;
+ };
+
+ max77686: pmic@09 {
+ compatible = "maxim,max77686";
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M1_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDQ_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_MMC2_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDDQ_MMC1_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_USB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_HSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "LDO20_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "LDO21_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "VDDQ_LCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-microvolt-offset = <50000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_CKEM1_2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "BUCK7_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "BUCK8_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+ };
+ };
+ };
+
+ exynos-usbphy@125B0000 {
+ status = "okay";
+ };
+
+ hsotg@12480000 {
+ status = "okay";
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+ };
+
+ ehci: ehci@12580000 {
+ status = "okay";
+ };
+};
new file mode 100644
@@ -0,0 +1,49 @@
+/*
+ * Hardkernel's Exynos4412 based ODROID-U3 board device tree source
+ *
+ * Copyright (c) 2014 Marek Szyprowski <m.szyprowski@samsung.com>
+ *
+ * Device tree source file for Hardkernel's ODROID-U3 board which is based
+ * on Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos4412-odroid-common.dtsi"
+
+/ {
+ model = "Hardkernel ODROID-U3 board based on Exynos4412";
+ compatible = "hardkernel,odroid-u3", "samsung,exynos4412", "samsung,exynos4";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led1 {
+ label = "led1:heart";
+ gpios = <&gpc1 0 1>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&usb3503 {
+ clock-names = "refclk";
+ clocks = <&pmu_system_controller 0>;
+ refclk-frequency = <24000000>;
+};
+
+&ehci {
+ port@1 {
+ status = "okay";
+ };
+ port@2 {
+ status = "okay";
+ };
+};
@@ -3,8 +3,8 @@
*
* Copyright (c) 2012 Dongjin Kim <tobetter@gmail.com>
*
- * Device tree source file for Hardkernel's ODROID-X board which is based on
- * Samsung's Exynos4412 SoC.
+ * Device tree source file for Hardkernel's ODROID-X board which is based
+ * on Samsung's Exynos4412 SoC.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -12,7 +12,7 @@
*/
/dts-v1/;
-#include "exynos4412.dtsi"
+#include "exynos4412-odroid-common.dtsi"
/ {
model = "Hardkernel ODROID-X board based on Exynos4412";
@@ -22,11 +22,6 @@
reg = <0x40000000 0x40000000>;
};
- firmware@0204F000 {
- compatible = "samsung,secure-firmware";
- reg = <0x0204F000 0x1000>;
- };
-
leds {
compatible = "gpio-leds";
led1 {
@@ -43,24 +38,12 @@
};
};
- mmc@12550000 {
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo20_reg &buck8_reg>;
+ serial@13820000 {
status = "okay";
+ };
- num-slots = <1>;
- supports-highspeed;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
-
- slot@0 {
- reg = <0>;
- bus-width = <8>;
- };
+ serial@13830000 {
+ status = "okay";
};
regulator_p3v3 {
@@ -70,299 +53,12 @@
regulator-max-microvolt = <3300000>;
gpio = <&gpa1 1 1>;
enable-active-high;
- regulator-boot-on;
- };
-
- watchdog@10060000 {
- status = "okay";
- };
-
- rtc@10070000 {
- status = "okay";
- };
-
- g2d@10800000 {
- status = "okay";
- };
-
- camera {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <>;
-
- fimc_0: fimc@11800000 {
- status = "okay";
- };
-
- fimc_1: fimc@11810000 {
- status = "okay";
- };
-
- fimc_2: fimc@11820000 {
- status = "okay";
- };
-
- fimc_3: fimc@11830000 {
- status = "okay";
- };
- };
-
- sdhci@12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo4_reg &ldo21_reg>;
- status = "okay";
- };
-
- serial@13800000 {
- status = "okay";
- };
-
- serial@13810000 {
- status = "okay";
- };
-
- serial@13820000 {
- status = "okay";
- };
-
- serial@13830000 {
- status = "okay";
- };
-
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
-
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
- };
-
- i2c@13860000 {
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- usb3503@08 {
- compatible = "smsc,usb3503";
- reg = <0x08>;
-
- intn-gpios = <&gpx3 0 0>;
- connect-gpios = <&gpx3 4 0>;
- reset-gpios = <&gpx3 5 0>;
- initial-mode = <1>;
- };
-
- max77686: pmic@09 {
- compatible = "maxim,max77686";
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_M1_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VDDQ_EXT_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VDDQ_MMC2_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "VDDQ_MMC1_3_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VDD10_XPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VDD18_ABB1_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "VDD33_USB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "VDDQ_C2C_W_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "VDD18_ABB0_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "VDD10_HSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "VDD18_HSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "LDO20_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "LDO21_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo25_reg: LDO25 {
- regulator-name = "VDDQ_LCD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-microvolt-offset = <50000>;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_CKEM1_2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "BUCK6_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "BUCK7_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- buck8_reg: BUCK8 {
- regulator-name = "BUCK8_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
- };
- };
- };
-
- exynos-usbphy@125B0000 {
- status = "okay";
- };
-
- hsotg@12480000 {
- status = "okay";
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
+ regulator-always-on;
};
+};
- ehci@12580000 {
+&ehci {
+ port@1 {
status = "okay";
- port@1 {
- status = "okay";
- };
};
};
new file mode 100644
@@ -0,0 +1,23 @@
+/*
+ * Hardkernel's Exynos4412 based ODROID-X2 board device tree source
+ *
+ * Copyright (c) 2012 Dongjin Kim <tobetter@gmail.com>
+ *
+ * Device tree source file for Hardkernel's ODROID-X2 board which is based
+ * on Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "exynos4412-odroidx.dts"
+
+/ {
+ model = "Hardkernel ODROID-X2 board based on Exynos4412";
+ compatible = "hardkernel,odroid-x2", "samsung,exynos4412", "samsung,exynos4";
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+};
This patch moves some parts of exynos4412-odroidx.dts to common exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz instead of 1.4GHz), while U2/U3 differs from X2 by different way of routing signals to host USB hub. It also lacks some hw modules not yet supported by those dts files (i.e. LCD & touch panel). Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> --- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 319 +++++++++++++++++++++++ arch/arm/boot/dts/exynos4412-odroidu3.dts | 49 ++++ arch/arm/boot/dts/exynos4412-odroidx.dts | 326 +----------------------- arch/arm/boot/dts/exynos4412-odroidx2.dts | 23 ++ 5 files changed, 404 insertions(+), 315 deletions(-) create mode 100644 arch/arm/boot/dts/exynos4412-odroid-common.dtsi create mode 100644 arch/arm/boot/dts/exynos4412-odroidu3.dts create mode 100644 arch/arm/boot/dts/exynos4412-odroidx2.dts