@@ -8,6 +8,16 @@ config DRM_BRIDGE
menu "bridge chips"
depends on DRM_BRIDGE
+config DRM_PS8622
+ tristate "Parade eDP/LVDS bridge"
+ depends on OF
+ depends on I2C
+ select DRM_PANEL
+ select BACKLIGHT_LCD_SUPPORT
+ select BACKLIGHT_CLASS_DEVICE
+ help
+ parade eDP-LVDS bridge chip driver.
+
config DRM_PTN3460
tristate "PTN3460 DP/LVDS bridge"
depends on OF
@@ -1,3 +1,4 @@
ccflags-y := -Iinclude/drm
+obj-$(CONFIG_DRM_PS8622) += ps8622.o
obj-$(CONFIG_DRM_PTN3460) += ptn3460.o
new file mode 100644
@@ -0,0 +1,681 @@
+/*
+ * Parade PS8622 eDP/LVDS bridge driver
+ *
+ * Copyright (C) 2014 Google, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pm.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drm_panel.h>
+
+#include "drmP.h"
+#include "drm_crtc.h"
+#include "drm_crtc_helper.h"
+
+/* Brightness scale on the Parade chip */
+#define PS8622_MAX_BRIGHTNESS 0xff
+
+/* Timings taken from the version 1.7 datasheet for the PS8622/PS8625 */
+#define PS8622_POWER_RISE_T1_MIN_US 10
+#define PS8622_POWER_RISE_T1_MAX_US 10000
+#define PS8622_RST_HIGH_T2_MIN_US 3000
+#define PS8622_RST_HIGH_T2_MAX_US 30000
+#define PS8622_PWMO_END_T12_MS 200
+#define PS8622_POWER_FALL_T16_MAX_US 10000
+#define PS8622_POWER_OFF_T17_MS 500
+
+#if ((PS8622_RST_HIGH_T2_MIN_US + PS8622_POWER_RISE_T1_MAX_US) > \
+ (PS8622_RST_HIGH_T2_MAX_US + PS8622_POWER_RISE_T1_MIN_US))
+#error "T2.min + T1.max must be less than T2.max + T1.min"
+#endif
+
+struct ps8622_bridge {
+ struct drm_connector connector;
+ struct i2c_client *client;
+ struct drm_bridge bridge;
+ struct drm_panel *panel;
+ struct regulator *v12;
+ struct backlight_device *bl;
+
+ struct gpio_desc *gpio_slp;
+ struct gpio_desc *gpio_rst;
+
+ u32 max_lane_count;
+ u32 lane_count;
+
+ bool enabled;
+};
+
+static inline struct ps8622_bridge *
+ bridge_to_ps8622(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct ps8622_bridge, bridge);
+}
+
+static inline struct ps8622_bridge *
+ connector_to_ps8622(struct drm_connector *connector)
+{
+ return container_of(connector, struct ps8622_bridge, connector);
+}
+
+static int ps8622_set(struct i2c_client *client, u8 page, u8 reg, u8 val)
+{
+ int ret;
+ struct i2c_adapter *adap = client->adapter;
+ struct i2c_msg msg;
+ u8 data[] = {reg, val};
+
+ msg.addr = client->addr + page;
+ msg.flags = 0;
+ msg.len = sizeof(data);
+ msg.buf = data;
+
+ ret = i2c_transfer(adap, &msg, 1);
+ if (ret != 1)
+ pr_warn("PS8622 I2C write (0x%02x,0x%02x,0x%02x) failed: %d\n",
+ client->addr + page, reg, val, ret);
+ return !(ret == 1);
+}
+
+static int ps8622_send_config(struct ps8622_bridge *ps8622)
+{
+ struct i2c_client *cl = ps8622->client;
+ int err = 0;
+
+ /* HPD low */
+ err = ps8622_set(cl, 0x02, 0xa1, 0x01);
+ if (err)
+ goto error;
+
+ /* SW setting: [1:0] SW output 1.2V voltage is lower to 96% */
+ err = ps8622_set(cl, 0x04, 0x14, 0x01);
+ if (err)
+ goto error;
+
+ /* RCO SS setting: [5:4] = b01 0.5%, b10 1%, b11 1.5% */
+ err = ps8622_set(cl, 0x04, 0xe3, 0x20);
+ if (err)
+ goto error;
+
+ /* [7] RCO SS enable */
+ err = ps8622_set(cl, 0x04, 0xe2, 0x80);
+ if (err)
+ goto error;
+
+ /* RPHY Setting
+ * [3:2] CDR tune wait cycle before measure for fine tune
+ * b00: 1us b01: 0.5us b10:2us, b11: 4us
+ */
+ err = ps8622_set(cl, 0x04, 0x8a, 0x0c);
+ if (err)
+ goto error;
+
+ /* [3] RFD always on */
+ err = ps8622_set(cl, 0x04, 0x89, 0x08);
+ if (err)
+ goto error;
+
+ /* CTN lock in/out: 20000ppm/80000ppm. Lock out 2 times. */
+ err = ps8622_set(cl, 0x04, 0x71, 0x2d);
+ if (err)
+ goto error;
+
+ /* 2.7G CDR settings: NOF=40LSB for HBR CDR setting */
+ err = ps8622_set(cl, 0x04, 0x7d, 0x07);
+ if (err)
+ goto error;
+
+ /* [1:0] Fmin=+4bands */
+ err = ps8622_set(cl, 0x04, 0x7b, 0x00);
+ if (err)
+ goto error;
+
+ /* [7:5] DCO_FTRNG=+-40% */
+ err = ps8622_set(cl, 0x04, 0x7a, 0xfd);
+ if (err)
+ goto error;
+
+ /* 1.62G CDR settings: [5:2]NOF=64LSB [1:0]DCO scale is 2/5 */
+ err = ps8622_set(cl, 0x04, 0xc0, 0x12);
+ if (err)
+ goto error;
+
+ /* Gitune=-37% */
+ err = ps8622_set(cl, 0x04, 0xc1, 0x92);
+ if (err)
+ goto error;
+
+ /* Fbstep=100% */
+ err = ps8622_set(cl, 0x04, 0xc2, 0x1c);
+ if (err)
+ goto error;
+
+ /* [7] LOS signal disable */
+ err = ps8622_set(cl, 0x04, 0x32, 0x80);
+ if (err)
+ goto error;
+
+ /* RPIO Setting: [7:4] LVDS driver bias current : 75% (250mV swing) */
+ err = ps8622_set(cl, 0x04, 0x00, 0xb0);
+ if (err)
+ goto error;
+
+ /* [7:6] Right-bar GPIO output strength is 8mA */
+ err = ps8622_set(cl, 0x04, 0x15, 0x40);
+ if (err)
+ goto error;
+
+ /* EQ Training State Machine Setting, RCO calibration start */
+ err = ps8622_set(cl, 0x04, 0x54, 0x10);
+ if (err)
+ goto error;
+
+ /* Logic, needs more than 10 I2C command */
+ /* [4:0] MAX_LANE_COUNT set to max supported lanes */
+ err = ps8622_set(cl, 0x01, 0x02, 0x80 | ps8622->max_lane_count);
+ if (err)
+ goto error;
+
+ /* [4:0] LANE_COUNT_SET set to chosen lane count */
+ err = ps8622_set(cl, 0x01, 0x21, 0x80 | ps8622->lane_count);
+ if (err)
+ goto error;
+
+ err = ps8622_set(cl, 0x00, 0x52, 0x20);
+ if (err)
+ goto error;
+
+ /* HPD CP toggle enable */
+ err = ps8622_set(cl, 0x00, 0xf1, 0x03);
+ if (err)
+ goto error;
+
+ err = ps8622_set(cl, 0x00, 0x62, 0x41);
+ if (err)
+ goto error;
+
+ /* Counter number, add 1ms counter delay */
+ err = ps8622_set(cl, 0x00, 0xf6, 0x01);
+ if (err)
+ goto error;
+
+ /* [6]PWM function control by DPCD0040f[7], default is PWM block */
+ err = ps8622_set(cl, 0x00, 0x77, 0x06);
+ if (err)
+ goto error;
+
+ /* 04h Adjust VTotal toleranceto fix the 30Hz no display issue */
+ err = ps8622_set(cl, 0x00, 0x4c, 0x04);
+ if (err)
+ goto error;
+
+ /* DPCD00400='h00, Parade OUI ='h001cf8 */
+ err = ps8622_set(cl, 0x01, 0xc0, 0x00);
+ if (err)
+ goto error;
+
+ /* DPCD00401='h1c */
+ err = ps8622_set(cl, 0x01, 0xc1, 0x1c);
+ if (err)
+ goto error;
+
+ /* DPCD00402='hf8 */
+ err = ps8622_set(cl, 0x01, 0xc2, 0xf8);
+ if (err)
+ goto error;
+
+ /* DPCD403~408 = ASCII code, D2SLV5='h4432534c5635 */
+ err = ps8622_set(cl, 0x01, 0xc3, 0x44);
+ if (err)
+ goto error;
+
+ /* DPCD404 */
+ err = ps8622_set(cl, 0x01, 0xc4, 0x32);
+ if (err)
+ goto error;
+
+ /* DPCD405 */
+ err = ps8622_set(cl, 0x01, 0xc5, 0x53);
+ if (err)
+ goto error;
+
+ /* DPCD406 */
+ err = ps8622_set(cl, 0x01, 0xc6, 0x4c);
+ if (err)
+ goto error;
+
+ /* DPCD407 */
+ err = ps8622_set(cl, 0x01, 0xc7, 0x56);
+ if (err)
+ goto error;
+
+ /* DPCD408 */
+ err = ps8622_set(cl, 0x01, 0xc8, 0x35);
+ if (err)
+ goto error;
+
+ /* DPCD40A, Initial Code major revision '01' */
+ err = ps8622_set(cl, 0x01, 0xca, 0x01);
+ if (err)
+ goto error;
+
+ /* DPCD40B, Initial Code minor revision '05' */
+ err = ps8622_set(cl, 0x01, 0xcb, 0x05);
+ if (err)
+ goto error;
+
+
+ if (ps8622->bl) {
+ /* DPCD720, internal PWM */
+ err = ps8622_set(cl, 0x01, 0xa5, 0xa0);
+ if (err)
+ goto error;
+
+ /* FFh for 100% brightness, 0h for 0% brightness */
+ err = ps8622_set(cl, 0x01, 0xa7,
+ ps8622->bl->props.brightness);
+ if (err)
+ goto error;
+ } else {
+ /* DPCD720, external PWM */
+ err = ps8622_set(cl, 0x01, 0xa5, 0x80);
+ if (err)
+ goto error;
+ }
+
+ /* Set LVDS output as 6bit-VESA mapping, single LVDS channel */
+ err = ps8622_set(cl, 0x01, 0xcc, 0x13);
+ if (err)
+ goto error;
+
+ /* Enable SSC set by register */
+ err = ps8622_set(cl, 0x02, 0xb1, 0x20);
+ if (err)
+ goto error;
+
+ /* Set SSC enabled and +/-1% central spreading */
+ err = ps8622_set(cl, 0x04, 0x10, 0x16);
+ if (err)
+ goto error;
+
+ /* Logic end */
+ /* MPU Clock source: LC => RCO */
+ err = ps8622_set(cl, 0x04, 0x59, 0x60);
+ if (err)
+ goto error;
+
+ /* LC -> RCO */
+ err = ps8622_set(cl, 0x04, 0x54, 0x14);
+ if (err)
+ goto error;
+
+ /* HPD high */
+ err = ps8622_set(cl, 0x02, 0xa1, 0x91);
+
+error:
+ return err ? -EIO : 0;
+}
+
+static int ps8622_backlight_update(struct backlight_device *bl)
+{
+ struct ps8622_bridge *ps8622 = dev_get_drvdata(&bl->dev);
+ int ret, brightness = bl->props.brightness;
+
+ if (bl->props.power != FB_BLANK_UNBLANK ||
+ bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
+ brightness = 0;
+
+ if (!ps8622->enabled)
+ return -EINVAL;
+
+ ret = ps8622_set(ps8622->client, 0x01, 0xa7, brightness);
+
+ return ret;
+}
+
+static const struct backlight_ops ps8622_backlight_ops = {
+ .update_status = ps8622_backlight_update,
+};
+
+static void ps8622_pre_enable(struct drm_bridge *bridge)
+{
+ struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
+ int ret;
+
+ if (ps8622->enabled)
+ return;
+
+ gpiod_set_value(ps8622->gpio_rst, 0);
+
+ if (ps8622->v12) {
+ ret = regulator_enable(ps8622->v12);
+ if (ret)
+ DRM_ERROR("fails to enable ps8622->v12");
+ }
+
+ if (drm_panel_prepare(ps8622->panel)) {
+ DRM_ERROR("failed to prepare panel\n");
+ return;
+ }
+
+ gpiod_set_value(ps8622->gpio_slp, 1);
+
+ /*
+ * T1 is the range of time that it takes for the power to rise after we
+ * enable the lcd/ps8622 fet. T2 is the range of time in which the
+ * data sheet specifies we should deassert the reset pin.
+ *
+ * If it takes T1.max for the power to rise, we need to wait atleast
+ * T2.min before deasserting the reset pin. If it takes T1.min for the
+ * power to rise, we need to wait at most T2.max before deasserting the
+ * reset pin.
+ */
+ usleep_range(PS8622_RST_HIGH_T2_MIN_US + PS8622_POWER_RISE_T1_MAX_US,
+ PS8622_RST_HIGH_T2_MAX_US + PS8622_POWER_RISE_T1_MIN_US);
+
+ gpiod_set_value(ps8622->gpio_rst, 1);
+
+ /* wait 20ms after RST high */
+ usleep_range(20000, 30000);
+
+ ret = ps8622_send_config(ps8622);
+ if (ret) {
+ DRM_ERROR("Failed to send config to bridge (%d)\n", ret);
+ return;
+ }
+
+ ps8622->enabled = true;
+}
+
+static void ps8622_enable(struct drm_bridge *bridge)
+{
+ struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
+
+ if (drm_panel_enable(ps8622->panel)) {
+ DRM_ERROR("failed to enable panel\n");
+ return;
+ }
+}
+
+static void ps8622_disable(struct drm_bridge *bridge)
+{
+ struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
+
+ if (drm_panel_disable(ps8622->panel)) {
+ DRM_ERROR("failed to disable panel\n");
+ return;
+ }
+ msleep(PS8622_PWMO_END_T12_MS);
+}
+
+static void ps8622_post_disable(struct drm_bridge *bridge)
+{
+ struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
+
+ if (!ps8622->enabled)
+ return;
+
+ ps8622->enabled = false;
+
+ /*
+ * This doesn't matter if the regulators are turned off, but something
+ * else might keep them on. In that case, we want to assert the slp gpio
+ * to lower power.
+ */
+ gpiod_set_value(ps8622->gpio_slp, 0);
+
+ if (drm_panel_unprepare(ps8622->panel)) {
+ DRM_ERROR("failed to unprepare panel\n");
+ return;
+ }
+
+ if (ps8622->v12)
+ regulator_disable(ps8622->v12);
+
+ /*
+ * Sleep for at least the amount of time that it takes the power rail to
+ * fall to prevent asserting the rst gpio from doing anything.
+ */
+ usleep_range(PS8622_POWER_FALL_T16_MAX_US,
+ 2 * PS8622_POWER_FALL_T16_MAX_US);
+ gpiod_set_value(ps8622->gpio_rst, 0);
+
+ msleep(PS8622_POWER_OFF_T17_MS);
+}
+
+static void ps8622_destroy(struct drm_bridge *bridge)
+{
+ drm_bridge_cleanup(bridge);
+}
+
+static int ps8622_get_modes(struct drm_connector *connector)
+{
+ struct ps8622_bridge *ps8622;
+
+ ps8622 = connector_to_ps8622(connector);
+
+ return drm_panel_get_modes(ps8622->panel);
+}
+
+static struct drm_encoder *ps8622_best_encoder(struct drm_connector *connector)
+{
+ struct ps8622_bridge *ps8622;
+
+ ps8622 = connector_to_ps8622(connector);
+
+ return ps8622->bridge.encoder;
+}
+
+static const struct drm_connector_helper_funcs ps8622_connector_helper_funcs = {
+ .get_modes = ps8622_get_modes,
+ .best_encoder = ps8622_best_encoder,
+};
+
+static enum drm_connector_status ps8622_detect(struct drm_connector *connector,
+ bool force)
+{
+ return connector_status_connected;
+}
+
+static void ps8622_connector_destroy(struct drm_connector *connector)
+{
+ drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs ps8622_connector_funcs = {
+ .dpms = drm_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = ps8622_detect,
+ .destroy = ps8622_connector_destroy,
+};
+
+int ps8622_attach(struct drm_bridge *bridge)
+{
+ struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
+ int ret;
+
+ ps8622->connector.polled = DRM_CONNECTOR_POLL_HPD;
+ ret = drm_connector_init(bridge->drm, &ps8622->connector,
+ &ps8622_connector_funcs, DRM_MODE_CONNECTOR_LVDS);
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector with drm\n");
+ return ret;
+ }
+ drm_connector_helper_add(&ps8622->connector,
+ &ps8622_connector_helper_funcs);
+ drm_connector_register(&ps8622->connector);
+ drm_mode_connector_attach_encoder(&ps8622->connector,
+ bridge->encoder);
+
+ if (ps8622->panel)
+ drm_panel_attach(ps8622->panel, &ps8622->connector);
+
+ drm_helper_hpd_irq_event(ps8622->connector.dev);
+
+ return ret;
+}
+
+static const struct drm_bridge_funcs ps8622_bridge_funcs = {
+ .pre_enable = ps8622_pre_enable,
+ .enable = ps8622_enable,
+ .disable = ps8622_disable,
+ .post_disable = ps8622_post_disable,
+ .destroy = ps8622_destroy,
+ .attach = ps8622_attach,
+};
+
+static const struct of_device_id ps8622_devices[] = {
+ {.compatible = "parade,ps8622",},
+ {.compatible = "parade,ps8625",},
+ {}
+};
+MODULE_DEVICE_TABLE(of, ps8622_devices);
+
+static int ps8622_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct device_node *panel_node;
+ struct ps8622_bridge *ps8622;
+ int ret;
+
+ ps8622 = devm_kzalloc(dev, sizeof(*ps8622), GFP_KERNEL);
+ if (!ps8622)
+ return -ENOMEM;
+
+ panel_node = of_parse_phandle(dev->of_node, "panel", 0);
+ if (panel_node) {
+ ps8622->panel = of_drm_find_panel(panel_node);
+ of_node_put(panel_node);
+ if (!ps8622->panel)
+ return -EPROBE_DEFER;
+ }
+
+ ps8622->client = client;
+
+ ps8622->v12 = devm_regulator_get(dev, "vdd12");
+ if (IS_ERR(ps8622->v12)) {
+ dev_info(dev, "no 1.2v regulator found for PS8622\n");
+ ps8622->v12 = NULL;
+ }
+
+ ps8622->gpio_slp = devm_gpiod_get(dev, "sleep");
+ if (IS_ERR(ps8622->gpio_slp)) {
+ ret = PTR_ERR(ps8622->gpio_slp);
+ dev_err(dev, "cannot get gpio_slp %d\n", ret);
+ return ret;
+ }
+ ret = gpiod_direction_output(ps8622->gpio_slp, 1);
+ if (ret) {
+ dev_err(dev, "cannot configure gpio_slp\n");
+ return ret;
+ }
+
+ ps8622->gpio_rst = devm_gpiod_get(dev, "reset");
+ if (IS_ERR(ps8622->gpio_rst)) {
+ ret = PTR_ERR(ps8622->gpio_rst);
+ dev_err(dev, "cannot get gpio_rst %d\n", ret);
+ return ret;
+ }
+ /*
+ * Assert the reset pin high to avoid the bridge being
+ * initialized prematurely
+ */
+ ret = gpiod_direction_output(ps8622->gpio_rst, 1);
+ if (ret) {
+ dev_err(dev, "cannot configure gpio_rst\n");
+ return ret;
+ }
+
+ ps8622->max_lane_count = id->driver_data;
+
+ if (of_property_read_u32(dev->of_node, "lane-count",
+ &ps8622->lane_count)) {
+ ps8622->lane_count = ps8622->max_lane_count;
+ } else if (ps8622->lane_count > ps8622->max_lane_count) {
+ dev_info(dev, "lane-count property is too high,"
+ "using max_lane_count\n");
+ ps8622->lane_count = ps8622->max_lane_count;
+ }
+
+ if (!of_find_property(dev->of_node, "use-external-pwm", NULL)) {
+ ps8622->bl = backlight_device_register("ps8622-backlight",
+ dev, ps8622, &ps8622_backlight_ops,
+ NULL);
+ if (IS_ERR(ps8622->bl)) {
+ DRM_ERROR("failed to register backlight\n");
+ ret = PTR_ERR(ps8622->bl);
+ ps8622->bl = NULL;
+ return ret;
+ }
+ ps8622->bl->props.max_brightness = PS8622_MAX_BRIGHTNESS;
+ ps8622->bl->props.brightness = PS8622_MAX_BRIGHTNESS;
+ }
+
+ ps8622->bridge.dev = dev;
+ ps8622->bridge.funcs = &ps8622_bridge_funcs;
+ ret = drm_bridge_add(&ps8622->bridge);
+ if (ret) {
+ DRM_ERROR("Failed to add bridge\n");
+ return ret;
+ }
+
+ i2c_set_clientdata(client, ps8622);
+
+ return 0;
+}
+
+static int ps8622_remove(struct i2c_client *client)
+{
+ struct ps8622_bridge *ps8622 = i2c_get_clientdata(client);
+
+ if (ps8622->bl)
+ backlight_device_unregister(ps8622->bl);
+
+ drm_bridge_remove(&ps8622->bridge);
+
+ return 0;
+}
+
+static const struct i2c_device_id ps8622_i2c_table[] = {
+ /* Device type, max_lane_count */
+ {"ps8622", 1},
+ {"ps8625", 2},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ps8622_i2c_table);
+
+struct i2c_driver ps8622_driver = {
+ .id_table = ps8622_i2c_table,
+ .probe = ps8622_probe,
+ .remove = ps8622_remove,
+ .driver = {
+ .name = "ps8622",
+ .owner = THIS_MODULE,
+ .of_match_table = ps8622_devices,
+ },
+};
+module_i2c_driver(ps8622_driver);
+
+MODULE_AUTHOR("Vincent Palatin <vpalatin@chromium.org>");
+MODULE_DESCRIPTION("Parade ps8622/ps8625 eDP-LVDS converter driver");
+MODULE_LICENSE("GPL v2");