@@ -7,6 +7,7 @@
*
* Simple MMC power sequence management
*/
+#include <linux/clk.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/device.h>
@@ -16,12 +17,14 @@
#include <linux/mmc/host.h>
+#include "core.h"
#include "pwrseq.h"
struct mmc_pwrseq_simple {
struct mmc_pwrseq pwrseq;
struct gpio_desc **reset_gpio;
int nr_gpios;
+ struct clk *ext_clk;
};
static void mmc_pwrseq_simple_pre_power_on(struct mmc_host *host)
@@ -30,6 +33,9 @@ static void mmc_pwrseq_simple_pre_power_on(struct mmc_host *host)
struct mmc_pwrseq_simple, pwrseq);
int i;
+ if (pwrseq->ext_clk)
+ clk_prepare_enable(pwrseq->ext_clk);
+
for (i = 0; i < pwrseq->nr_gpios; i++)
if (!IS_ERR(pwrseq->reset_gpio[i]))
gpiod_set_value_cansleep(pwrseq->reset_gpio[i], 1);
@@ -46,12 +52,29 @@ static void mmc_pwrseq_simple_post_power_on(struct mmc_host *host)
gpiod_set_value_cansleep(pwrseq->reset_gpio[i], 0);
}
+static void mmc_pwrseq_simple_power_off(struct mmc_host *host)
+{
+ struct mmc_pwrseq_simple *pwrseq = container_of(host->pwrseq,
+ struct mmc_pwrseq_simple, pwrseq);
+ int i;
+
+ for (i = 0; i < pwrseq->nr_gpios; i++)
+ if (!IS_ERR(pwrseq->reset_gpio[i]))
+ gpiod_set_value_cansleep(pwrseq->reset_gpio[i], 1);
+
+ if (pwrseq->ext_clk)
+ clk_disable_unprepare(pwrseq->ext_clk);
+}
+
static void mmc_pwrseq_simple_free(struct mmc_host *host)
{
struct mmc_pwrseq_simple *pwrseq = container_of(host->pwrseq,
struct mmc_pwrseq_simple, pwrseq);
int i;
+ if (pwrseq->ext_clk)
+ clk_put(pwrseq->ext_clk);
+
if (pwrseq->nr_gpios > 0) {
for (i = 0; i < pwrseq->nr_gpios; i++)
if (!IS_ERR(pwrseq->reset_gpio[i]))
@@ -66,7 +89,7 @@ static void mmc_pwrseq_simple_free(struct mmc_host *host)
static struct mmc_pwrseq_ops mmc_pwrseq_simple_ops = {
.pre_power_on = mmc_pwrseq_simple_pre_power_on,
.post_power_on = mmc_pwrseq_simple_post_power_on,
- .power_off = mmc_pwrseq_simple_pre_power_on,
+ .power_off = mmc_pwrseq_simple_power_off,
.free = mmc_pwrseq_simple_free,
};
@@ -97,6 +120,14 @@ int mmc_pwrseq_simple_alloc(struct mmc_host *host, struct device *dev)
}
}
+ pwrseq->ext_clk = clk_get(dev, "ext_clock");
+ if (IS_ERR(pwrseq->ext_clk) &&
+ PTR_ERR(pwrseq->ext_clk) != -ENOENT &&
+ PTR_ERR(pwrseq->ext_clk) != -ENOSYS) {
+ ret = PTR_ERR(pwrseq->ext_clk);
+ goto free;
+ }
+
pwrseq->pwrseq.ops = &mmc_pwrseq_simple_ops;
host->pwrseq = &pwrseq->pwrseq;
Some WLAN chips attached to a SDIO interface, need a reference clock. Since this is very common, extend the prseq_simple driver to support an optional clock that is enabled prior the card power up procedure. Note, the external clock is optional. Thus an error is not returned if the clock is not found. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> --- drivers/mmc/core/pwrseq_simple.c | 33 ++++++++++++++++++++++++++++++++- 1 file changed, 32 insertions(+), 1 deletion(-)