new file mode 100644
@@ -0,0 +1,90 @@
+Rockchip RK3288 specific extensions to the Analogix Display Port
+================================
+
+Required properties:
+- compatible: "rockchip,rk3288-edp";
+
+- reg: physical base address of the controller and length
+
+- clocks: from common clock binding: handle to dp clock.
+ of memory mapped region.
+
+- clock-names: from common clock binding:
+ Required elements: "dp" "pclk"
+
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+
+- pinctrl-names: Names corresponding to the chip hotplug pinctrl states.
+- pinctrl-0: pin-control mode. should be <&edp_hpd>
+
+- reset-names: Must include the name "dp"
+
+- rockchip,grf: this soc should set GRF regs, so need get grf here.
+
+- ports: contain a port node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+
+For the below properties, please refer to Analogix DP binding document:
+ * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
+- phys (required)
+- phy-names (required)
+- hpd-gpios (optional)
+-------------------------------------------------------------------------------
+
+Example:
+ dp-controller: dp@ff970000 {
+ compatible = "rockchip,rk3288-dp";
+ reg = <0xff970000 0x4000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>;
+ clock-names = "dp", "pclk";
+ phys = <&dp_phy>;
+ phy-names = "dp";
+
+ rockchip,grf = <&grf>;
+ resets = <&cru 111>;
+ reset-names = "dp";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ edp_in: port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ edp_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_edp>;
+ };
+ edp_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_edp>;
+ };
+ };
+
+ edp_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ edp_out_panel: endpoint {
+ reg = <0>;
+ remote-endpoint = <&panel_in_edp>
+ };
+ };
+ };
+ };
+
+ pinctrl {
+ edp {
+ edp_hpd: edp-hpd {
+ rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+ };
Rockchip DP driver is a helper driver of analogix_dp coder driver, so most of the DT property should be descriped in analogix_dp document. Signed-off-by: Yakir Yang <ykk@rock-chips.com> --- Changes in v5: - Split binding doc's from driver changes. (Rob) - Add eDP hotplug pinctrl property. (Heiko) Changes in v4: None Changes in v3: None Changes in v2: None .../bindings/video/analogix_dp-rockchip.txt | 90 ++++++++++++++++++++++ 1 file changed, 90 insertions(+) create mode 100644 Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt