| Message ID | 1446458641-4447-1-git-send-email-alim.akhtar@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hello Alim, This patch looks mostly good to me, I just have two comments below: On 11/02/2015 11:04 AM, Alim Akhtar wrote: > This patch add pmic (s2mps15) node of espresso board, > which includes addition of regulators and pmic-clk sub-nodes. > > Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> > --- > This patch should go in after driver side changes [1] lands. > [1]-> https://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg47736.html > > arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 +++++++++++++++++++++++ > 1 file changed, 349 insertions(+) > > diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts > index 838a3626dac1..8ce04a0ec928 100644 > --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts > +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts > @@ -53,6 +53,355 @@ > status = "okay"; > }; > > +&hsi2c_4 { > + samsung,i2c-sda-delay = <100>; > + samsung,i2c-max-bus-freq = <200000>; > + status = "okay"; > + > + s2mps15_pmic@66 { > + compatible = "samsung,s2mps15-pmic"; > + reg = <0x66>; > + interrupts = <2 0>; Maybe using IRQ_TYPE_NONE instead of 0? > + interrupt-parent = <&gpa0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_irq>; > + wakeup-source; > + > + s2mps15_osc: clocks { > + compatible = "samsung,s2mps13-clk"; > + #clock-cells = <1>; > + clock-output-names = "s2mps13_ap", "s2mps13_cp", > + "s2mps13_bt"; > + }; > + > + regulators { > + ldo1_reg: LDO1 { > + regulator-name = "vdd_ldo1"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <900000>; > + regulator-always-on; I see that all regulators are marked as regulator-always-on but that will prevent the regulator subsystem to disable unused regulators. Can you please double check which regulators should really be always on and which ones can be disabled if are not used? After those two changes: Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Best regards,
On 11/02/2015 05:00 PM, Javier Martinez Canillas wrote: > Hello Alim, > > This patch looks mostly good to me, I just have two comments below: > > On 11/02/2015 11:04 AM, Alim Akhtar wrote: >> This patch add pmic (s2mps15) node of espresso board, >> which includes addition of regulators and pmic-clk sub-nodes. >> >> Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> >> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> >> --- >> This patch should go in after driver side changes [1] lands. >> [1]-> https://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg47736.html >> >> arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 +++++++++++++++++++++++ >> 1 file changed, 349 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >> index 838a3626dac1..8ce04a0ec928 100644 >> --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >> +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >> @@ -53,6 +53,355 @@ >> status = "okay"; >> }; >> >> +&hsi2c_4 { >> + samsung,i2c-sda-delay = <100>; >> + samsung,i2c-max-bus-freq = <200000>; >> + status = "okay"; >> + >> + s2mps15_pmic@66 { >> + compatible = "samsung,s2mps15-pmic"; >> + reg = <0x66>; >> + interrupts = <2 0>; > > Maybe using IRQ_TYPE_NONE instead of 0? > Ok will check >> + interrupt-parent = <&gpa0>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pmic_irq>; >> + wakeup-source; >> + >> + s2mps15_osc: clocks { >> + compatible = "samsung,s2mps13-clk"; >> + #clock-cells = <1>; >> + clock-output-names = "s2mps13_ap", "s2mps13_cp", >> + "s2mps13_bt"; >> + }; >> + >> + regulators { >> + ldo1_reg: LDO1 { >> + regulator-name = "vdd_ldo1"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <900000>; >> + regulator-always-on; > > I see that all regulators are marked as regulator-always-on but that will > prevent the regulator subsystem to disable unused regulators. Can you please > double check which regulators should really be always on and which ones can > be disabled if are not used? > I kept it on always, as I am still in a process for validating all IPs on board. Will see if I can remove some of them, which I feel can be done. > After those two changes: > > Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> > Thanks! > Best regards, > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
2015-11-02 19:04 GMT+09:00 Alim Akhtar <alim.akhtar@samsung.com>: > This patch add pmic (s2mps15) node of espresso board, This patch adds PMIC (S2MPS15)... > which includes addition of regulators and pmic-clk sub-nodes. > > Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> > --- > This patch should go in after driver side changes [1] lands. > [1]-> https://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg47736.html Eh? Why? Usually there is not such requirement. > > arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 +++++++++++++++++++++++ > 1 file changed, 349 insertions(+) > > diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts > index 838a3626dac1..8ce04a0ec928 100644 > --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts > +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts > @@ -53,6 +53,355 @@ > status = "okay"; > }; > > +&hsi2c_4 { > + samsung,i2c-sda-delay = <100>; > + samsung,i2c-max-bus-freq = <200000>; > + status = "okay"; > + > + s2mps15_pmic@66 { > + compatible = "samsung,s2mps15-pmic"; > + reg = <0x66>; > + interrupts = <2 0>; > + interrupt-parent = <&gpa0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_irq>; > + wakeup-source; > + > + s2mps15_osc: clocks { > + compatible = "samsung,s2mps13-clk"; > + #clock-cells = <1>; > + clock-output-names = "s2mps13_ap", "s2mps13_cp", > + "s2mps13_bt"; > + }; Don't you want to use one of these clocks for s3c-rtc (&rtc node)? > + > + regulators { > + ldo1_reg: LDO1 { > + regulator-name = "vdd_ldo1"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <900000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo2_reg: LDO2 { > + regulator-name = "vdd_ldo2"; > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <3300000>; > + regulator-enable-ramp-delay = <125>; > + regulator-always-on; > + }; > + > + ldo3_reg: LDO3 { > + regulator-name = "vdd_ldo3"; > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <1980000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo4_reg: LDO4 { > + regulator-name = "vdd_ldo4"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1110000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo5_reg: LDO5 { > + regulator-name = "vdd_ldo5"; > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <1980000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo6_reg: LDO6 { > + regulator-name = "vdd_ldo6"; > + regulator-min-microvolt = <2250000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo7_reg: LDO7 { > + regulator-name = "vdd_ldo7"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1150000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo8_reg: LDO8 { > + regulator-name = "vdd_ldo8"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo9_reg: LDO9 { > + regulator-name = "vdd_ldo9"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo10_reg: LDO10 { > + regulator-name = "vdd_ldo10"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo11_reg: LDO11 { > + regulator-name = "vdd_ldo11"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo12_reg: LDO12 { > + regulator-name = "vdd_ldo12"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo13_reg: LDO13 { > + regulator-name = "vdd_ldo13"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo14_reg: LDO14 { > + regulator-name = "vdd_ldo14"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3375000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo15_reg: LDO15 { > + regulator-name = "vdd_ldo15"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <2275000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo16_reg: LDO16 { > + regulator-name = "vdd_ldo16"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo17_reg: LDO17 { > + regulator-name = "vdd_ldo17"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3375000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo18_reg: LDO18 { > + regulator-name = "vdd_ldo18"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <2275000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo19_reg: LDO19 { > + regulator-name = "vdd_ldo19"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3375000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo20_reg: LDO20 { > + regulator-name = "vdd_ldo20"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <2275000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo21_reg: LDO21 { > + regulator-name = "vdd_ldo21"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3375000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo22_reg: LDO22 { > + regulator-name = "vdd_ldo22"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo23_reg: LDO23 { > + regulator-name = "vdd_ldo23"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <2275000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo24_reg: LDO24 { > + regulator-name = "vdd_ldo24"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3375000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo25_reg: LDO25 { > + regulator-name = "vdd_ldo25"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3375000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo26_reg: LDO26 { > + regulator-name = "vdd_ldo26"; > + regulator-min-microvolt = <700000>; > + regulator-max-microvolt = <1470000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + ldo27_reg: LDO27 { > + regulator-name = "vdd_ldo27"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <2275000>; > + regulator-always-on; > + regulator-enable-ramp-delay = <125>; > + }; > + > + buck1_reg: BUCK1 { > + regulator-name = "vdd_mif"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <25000>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck2_reg: BUCK2 { > + regulator-name = "vdd_atlas"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <12500>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck3_reg: BUCK3 { > + regulator-name = "vdd_apollo"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <12500>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck4_reg: BUCK4 { > + regulator-name = "vdd_int"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <12500>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck5_reg: BUCK5 { > + regulator-name = "vdd_buck5"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-ramp-delay = <25000>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck6_reg: BUCK6 { > + regulator-name = "vdd_g3d"; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1400000>; > + regulator-always-on; > + regulator-ramp-delay = <12500>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck7_reg: BUCK7 { > + regulator-name = "vdd_buck7"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <25000>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck8_reg: BUCK8 { > + regulator-name = "vdd_buck8"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1500000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <25000>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck9_reg: BUCK9 { > + regulator-name = "vdd_buck9"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + regulator-always-on; > + regulator-boot-on; > + regulator-ramp-delay = <25000>; > + regulator-enable-ramp-delay = <250>; > + }; > + > + buck10_reg: BUCK10 { > + regulator-name = "vdd_buck10"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <3000000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <25000>; > + regulator-enable-ramp-delay = <250>; > + }; All of these ldo3 and bucks in vendor tree for Espresso board have ramp delay of 12000. Also they don't have enable-ramp-delay set and voltages sometimes differ. I don't have S2MPS15 datasheet so I don't know what is the true value... I'll leave it up to you but it looks suspicious. > + }; > + }; > +}; What will be the benefit of defining all of these regulators if they are always on and without consumers? No one will disable them, no one will change the voltage. Please provide some consumers. Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 11/02/2015 05:55 PM, Krzysztof Kozlowski wrote: > 2015-11-02 19:04 GMT+09:00 Alim Akhtar <alim.akhtar@samsung.com>: >> This patch add pmic (s2mps15) node of espresso board, > > This patch adds PMIC (S2MPS15)... > >> which includes addition of regulators and pmic-clk sub-nodes. >> >> Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> >> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> >> --- >> This patch should go in after driver side changes [1] lands. >> [1]-> https://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg47736.html > > Eh? Why? Usually there is not such requirement. > Got it, I just thought without driver changes these dts modification does not make sense. Thanks for clarification. >> >> arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 +++++++++++++++++++++++ >> 1 file changed, 349 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >> index 838a3626dac1..8ce04a0ec928 100644 >> --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >> +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >> @@ -53,6 +53,355 @@ >> status = "okay"; >> }; >> >> +&hsi2c_4 { >> + samsung,i2c-sda-delay = <100>; >> + samsung,i2c-max-bus-freq = <200000>; >> + status = "okay"; >> + >> + s2mps15_pmic@66 { >> + compatible = "samsung,s2mps15-pmic"; >> + reg = <0x66>; >> + interrupts = <2 0>; >> + interrupt-parent = <&gpa0>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pmic_irq>; >> + wakeup-source; >> + >> + s2mps15_osc: clocks { >> + compatible = "samsung,s2mps13-clk"; >> + #clock-cells = <1>; >> + clock-output-names = "s2mps13_ap", "s2mps13_cp", >> + "s2mps13_bt"; >> + }; > > Don't you want to use one of these clocks for s3c-rtc (&rtc node)? > yes, you are right, rtc on this board is currently broken, mainly because of the introduction of rtc_src clock in the s3c-rtc driver. That is on my do list next. will take a look. Are you suggesting to remove this -clk node now and add along with rtc changes? I feel this should go in along with this patch. >> + >> + regulators { >> + ldo1_reg: LDO1 { >> + regulator-name = "vdd_ldo1"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <900000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo2_reg: LDO2 { >> + regulator-name = "vdd_ldo2"; >> + regulator-min-microvolt = <1620000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-enable-ramp-delay = <125>; >> + regulator-always-on; >> + }; >> + >> + ldo3_reg: LDO3 { >> + regulator-name = "vdd_ldo3"; >> + regulator-min-microvolt = <1620000>; >> + regulator-max-microvolt = <1980000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo4_reg: LDO4 { >> + regulator-name = "vdd_ldo4"; >> + regulator-min-microvolt = <800000>; >> + regulator-max-microvolt = <1110000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo5_reg: LDO5 { >> + regulator-name = "vdd_ldo5"; >> + regulator-min-microvolt = <1620000>; >> + regulator-max-microvolt = <1980000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo6_reg: LDO6 { >> + regulator-name = "vdd_ldo6"; >> + regulator-min-microvolt = <2250000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo7_reg: LDO7 { >> + regulator-name = "vdd_ldo7"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1150000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo8_reg: LDO8 { >> + regulator-name = "vdd_ldo8"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo9_reg: LDO9 { >> + regulator-name = "vdd_ldo9"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo10_reg: LDO10 { >> + regulator-name = "vdd_ldo10"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo11_reg: LDO11 { >> + regulator-name = "vdd_ldo11"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo12_reg: LDO12 { >> + regulator-name = "vdd_ldo12"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo13_reg: LDO13 { >> + regulator-name = "vdd_ldo13"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo14_reg: LDO14 { >> + regulator-name = "vdd_ldo14"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3375000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo15_reg: LDO15 { >> + regulator-name = "vdd_ldo15"; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <2275000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo16_reg: LDO16 { >> + regulator-name = "vdd_ldo16"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo17_reg: LDO17 { >> + regulator-name = "vdd_ldo17"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3375000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo18_reg: LDO18 { >> + regulator-name = "vdd_ldo18"; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <2275000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo19_reg: LDO19 { >> + regulator-name = "vdd_ldo19"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3375000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo20_reg: LDO20 { >> + regulator-name = "vdd_ldo20"; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <2275000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo21_reg: LDO21 { >> + regulator-name = "vdd_ldo21"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3375000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo22_reg: LDO22 { >> + regulator-name = "vdd_ldo22"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo23_reg: LDO23 { >> + regulator-name = "vdd_ldo23"; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <2275000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo24_reg: LDO24 { >> + regulator-name = "vdd_ldo24"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3375000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo25_reg: LDO25 { >> + regulator-name = "vdd_ldo25"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3375000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo26_reg: LDO26 { >> + regulator-name = "vdd_ldo26"; >> + regulator-min-microvolt = <700000>; >> + regulator-max-microvolt = <1470000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + ldo27_reg: LDO27 { >> + regulator-name = "vdd_ldo27"; >> + regulator-min-microvolt = <1500000>; >> + regulator-max-microvolt = <2275000>; >> + regulator-always-on; >> + regulator-enable-ramp-delay = <125>; >> + }; >> + >> + buck1_reg: BUCK1 { >> + regulator-name = "vdd_mif"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <25000>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck2_reg: BUCK2 { >> + regulator-name = "vdd_atlas"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <12500>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck3_reg: BUCK3 { >> + regulator-name = "vdd_apollo"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <12500>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck4_reg: BUCK4 { >> + regulator-name = "vdd_int"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <12500>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck5_reg: BUCK5 { >> + regulator-name = "vdd_buck5"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-always-on; >> + regulator-ramp-delay = <25000>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck6_reg: BUCK6 { >> + regulator-name = "vdd_g3d"; >> + regulator-min-microvolt = <500000>; >> + regulator-max-microvolt = <1400000>; >> + regulator-always-on; >> + regulator-ramp-delay = <12500>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck7_reg: BUCK7 { >> + regulator-name = "vdd_buck7"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1500000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <25000>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck8_reg: BUCK8 { >> + regulator-name = "vdd_buck8"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1500000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <25000>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck9_reg: BUCK9 { >> + regulator-name = "vdd_buck9"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <2100000>; >> + regulator-always-on; >> + regulator-boot-on; >> + regulator-ramp-delay = <25000>; >> + regulator-enable-ramp-delay = <250>; >> + }; >> + >> + buck10_reg: BUCK10 { >> + regulator-name = "vdd_buck10"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-boot-on; >> + regulator-always-on; >> + regulator-ramp-delay = <25000>; >> + regulator-enable-ramp-delay = <250>; >> + }; > > All of these ldo3 and bucks in vendor tree for Espresso board have > ramp delay of 12000. Also they don't have enable-ramp-delay set and > voltages sometimes differ. I don't have S2MPS15 datasheet so I don't > know what is the true value... I'll leave it up to you but it looks > suspicious. > These values generally comes from our board design team, so I cann't really comment on that, it may vary from board revision etc. I will check if we have any updated version of recommended value and update accordingly. >> + }; >> + }; >> +}; > > What will be the benefit of defining all of these regulators if they > are always on and without consumers? No one will disable them, no one > will change the voltage. Please provide some consumers. > As many drivers are not yet enabled in arm64 defconfig, that is one of the reason why we are not seeing many consumer for these nodes. This is the ground work being done for enabling those. If you insist will try to reduce what is being used now. Moreover this was used to verify functionality of pmic driver as well. > Best regards, > Krzysztof > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
2015-11-02 22:01 GMT+09:00 Alim Akhtar <alim.akhtar@samsung.com>: >>> >>> arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 >>> +++++++++++++++++++++++ >>> 1 file changed, 349 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>> b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>> index 838a3626dac1..8ce04a0ec928 100644 >>> --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>> +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>> @@ -53,6 +53,355 @@ >>> status = "okay"; >>> }; >>> >>> +&hsi2c_4 { >>> + samsung,i2c-sda-delay = <100>; >>> + samsung,i2c-max-bus-freq = <200000>; >>> + status = "okay"; >>> + >>> + s2mps15_pmic@66 { >>> + compatible = "samsung,s2mps15-pmic"; >>> + reg = <0x66>; >>> + interrupts = <2 0>; >>> + interrupt-parent = <&gpa0>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&pmic_irq>; >>> + wakeup-source; >>> + >>> + s2mps15_osc: clocks { >>> + compatible = "samsung,s2mps13-clk"; >>> + #clock-cells = <1>; >>> + clock-output-names = "s2mps13_ap", "s2mps13_cp", >>> + "s2mps13_bt"; >>> + }; >> >> >> Don't you want to use one of these clocks for s3c-rtc (&rtc node)? >> > yes, you are right, rtc on this board is currently broken, mainly because of > the introduction of rtc_src clock in the s3c-rtc driver. > That is on my do list next. will take a look. > > Are you suggesting to remove this -clk node now and add along with rtc > changes? I feel this should go in along with this patch. Just add it in consecutive patch in this series. You added here some providers (clock and regulators) without consumers. This of course looks good as a way of providing full description of the board but: 1. For regulators always on: may be meaningless for kernel. Kernel does not use it. Existence of regulator subnode will fulfill driver's needs for probe. 2. For clocks: actually will disable these clocks because of lack of consumers... which is fine but probably not what you wanted. The standard approach is to add such providers when they are needed - there are some consumers using them. >>> + >>> + regulators { >>> + ldo1_reg: LDO1 { >>> + regulator-name = "vdd_ldo1"; >>> + regulator-min-microvolt = <500000>; >>> + regulator-max-microvolt = <900000>; >>> + regulator-always-on; >>> + regulator-enable-ramp-delay = <125>; >>> + }; (...) >>> + >>> + buck10_reg: BUCK10 { >>> + regulator-name = "vdd_buck10"; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <3000000>; >>> + regulator-boot-on; >>> + regulator-always-on; >>> + regulator-ramp-delay = <25000>; >>> + regulator-enable-ramp-delay = <250>; >>> + }; >> >> >> All of these ldo3 and bucks in vendor tree for Espresso board have >> ramp delay of 12000. Also they don't have enable-ramp-delay set and >> voltages sometimes differ. I don't have S2MPS15 datasheet so I don't >> know what is the true value... I'll leave it up to you but it looks >> suspicious. >> > These values generally comes from our board design team, so I cann't really > comment on that, it may vary from board revision etc. > I will check if we have any updated version of recommended value and update > accordingly. Okay, just pointing the difference. I cannot verify them. > >>> + }; >>> + }; >>> +}; >> >> >> What will be the benefit of defining all of these regulators if they >> are always on and without consumers? No one will disable them, no one >> will change the voltage. Please provide some consumers. >> > As many drivers are not yet enabled in arm64 defconfig, that is one of the > reason why we are not seeing many consumer for these nodes. That is not a problem. Please send a patch changing the defconfig. Usually defconfig (for armv7 this would be exynos and multi_v7) should provide bootable and working environment for all of our supported boards. > This is the ground work being done for enabling those. If you insist will > try to reduce what is being used now. Moreover this was used to verify > functionality of pmic driver as well. Actually as a verification I think even adding simple node "regulators" is sufficient - driver will add all regulators anyway. However seeing all regulators described for particular board is good... but lack of consumers is disturbing because this may mean that it was not really fully modeled. From my point of view - all of regulators in DT are welcomed but at least some of them should have a consumer. This means that someone took care and looked at the relationships between them. Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Krzysztof On 11/02/2015 07:22 PM, Krzysztof Kozlowski wrote: > 2015-11-02 22:01 GMT+09:00 Alim Akhtar <alim.akhtar@samsung.com>: >>>> >>>> arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 >>>> +++++++++++++++++++++++ >>>> 1 file changed, 349 insertions(+) >>>> >>>> diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>> b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>> index 838a3626dac1..8ce04a0ec928 100644 >>>> --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>> +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>> @@ -53,6 +53,355 @@ >>>> status = "okay"; >>>> }; >>>> >>>> +&hsi2c_4 { >>>> + samsung,i2c-sda-delay = <100>; >>>> + samsung,i2c-max-bus-freq = <200000>; >>>> + status = "okay"; >>>> + >>>> + s2mps15_pmic@66 { >>>> + compatible = "samsung,s2mps15-pmic"; >>>> + reg = <0x66>; >>>> + interrupts = <2 0>; >>>> + interrupt-parent = <&gpa0>; >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&pmic_irq>; >>>> + wakeup-source; >>>> + >>>> + s2mps15_osc: clocks { >>>> + compatible = "samsung,s2mps13-clk"; >>>> + #clock-cells = <1>; >>>> + clock-output-names = "s2mps13_ap", "s2mps13_cp", >>>> + "s2mps13_bt"; >>>> + }; >>> >>> >>> Don't you want to use one of these clocks for s3c-rtc (&rtc node)? >>> >> yes, you are right, rtc on this board is currently broken, mainly because of >> the introduction of rtc_src clock in the s3c-rtc driver. >> That is on my do list next. will take a look. >> >> Are you suggesting to remove this -clk node now and add along with rtc >> changes? I feel this should go in along with this patch. > > Just add it in consecutive patch in this series. You added here some > providers (clock and regulators) without consumers. This of course > looks good as a way of providing full description of the board but: > 1. For regulators always on: may be meaningless for kernel. Kernel > does not use it. Existence of regulator subnode will fulfill driver's > needs for probe. > 2. For clocks: actually will disable these clocks because of lack of > consumers... which is fine but probably not what you wanted. > > The standard approach is to add such providers when they are needed - > there are some consumers using them. > OK. for now will keep the pmic clock added as clock will be in disabled state, so it wont harm. - will keep system related regulator like supply to arm,mif,int etc .. will remove supplies to other peripherals IPs. Hope thats fine. >>>> + >>>> + regulators { >>>> + ldo1_reg: LDO1 { >>>> + regulator-name = "vdd_ldo1"; >>>> + regulator-min-microvolt = <500000>; >>>> + regulator-max-microvolt = <900000>; >>>> + regulator-always-on; >>>> + regulator-enable-ramp-delay = <125>; >>>> + }; > > (...) > >>>> + >>>> + buck10_reg: BUCK10 { >>>> + regulator-name = "vdd_buck10"; >>>> + regulator-min-microvolt = <1000000>; >>>> + regulator-max-microvolt = <3000000>; >>>> + regulator-boot-on; >>>> + regulator-always-on; >>>> + regulator-ramp-delay = <25000>; >>>> + regulator-enable-ramp-delay = <250>; >>>> + }; >>> >>> >>> All of these ldo3 and bucks in vendor tree for Espresso board have >>> ramp delay of 12000. Also they don't have enable-ramp-delay set and >>> voltages sometimes differ. I don't have S2MPS15 datasheet so I don't >>> know what is the true value... I'll leave it up to you but it looks >>> suspicious. >>> >> These values generally comes from our board design team, so I cann't really >> comment on that, it may vary from board revision etc. >> I will check if we have any updated version of recommended value and update >> accordingly. > > Okay, just pointing the difference. I cannot verify them. > >> >>>> + }; >>>> + }; >>>> +}; >>> >>> >>> What will be the benefit of defining all of these regulators if they >>> are always on and without consumers? No one will disable them, no one >>> will change the voltage. Please provide some consumers. >>> >> As many drivers are not yet enabled in arm64 defconfig, that is one of the >> reason why we are not seeing many consumer for these nodes. > > That is not a problem. Please send a patch changing the defconfig. > Usually defconfig (for armv7 this would be exynos and multi_v7) should > provide bootable and working environment for all of our supported > boards. > >> This is the ground work being done for enabling those. If you insist will >> try to reduce what is being used now. Moreover this was used to verify >> functionality of pmic driver as well. > > Actually as a verification I think even adding simple node > "regulators" is sufficient - driver will add all regulators anyway. > However seeing all regulators described for particular board is > good... but lack of consumers is disturbing because this may mean that > it was not really fully modeled. > >>From my point of view - all of regulators in DT are welcomed but at > least some of them should have a consumer. This means that someone > took care and looked at the relationships between them. > > Best regards, > Krzysztof > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 05.11.2015 14:37, Alim Akhtar wrote: > Hi Krzysztof > > On 11/02/2015 07:22 PM, Krzysztof Kozlowski wrote: >> 2015-11-02 22:01 GMT+09:00 Alim Akhtar <alim.akhtar@samsung.com>: >>>>> >>>>> arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 349 >>>>> +++++++++++++++++++++++ >>>>> 1 file changed, 349 insertions(+) >>>>> >>>>> diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>>> b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>>> index 838a3626dac1..8ce04a0ec928 100644 >>>>> --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>>> +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts >>>>> @@ -53,6 +53,355 @@ >>>>> status = "okay"; >>>>> }; >>>>> >>>>> +&hsi2c_4 { >>>>> + samsung,i2c-sda-delay = <100>; >>>>> + samsung,i2c-max-bus-freq = <200000>; >>>>> + status = "okay"; >>>>> + >>>>> + s2mps15_pmic@66 { >>>>> + compatible = "samsung,s2mps15-pmic"; >>>>> + reg = <0x66>; >>>>> + interrupts = <2 0>; >>>>> + interrupt-parent = <&gpa0>; >>>>> + pinctrl-names = "default"; >>>>> + pinctrl-0 = <&pmic_irq>; >>>>> + wakeup-source; >>>>> + >>>>> + s2mps15_osc: clocks { >>>>> + compatible = "samsung,s2mps13-clk"; >>>>> + #clock-cells = <1>; >>>>> + clock-output-names = "s2mps13_ap", >>>>> "s2mps13_cp", >>>>> + "s2mps13_bt"; >>>>> + }; >>>> >>>> >>>> Don't you want to use one of these clocks for s3c-rtc (&rtc node)? >>>> >>> yes, you are right, rtc on this board is currently broken, mainly >>> because of >>> the introduction of rtc_src clock in the s3c-rtc driver. >>> That is on my do list next. will take a look. >>> >>> Are you suggesting to remove this -clk node now and add along with rtc >>> changes? I feel this should go in along with this patch. >> >> Just add it in consecutive patch in this series. You added here some >> providers (clock and regulators) without consumers. This of course >> looks good as a way of providing full description of the board but: >> 1. For regulators always on: may be meaningless for kernel. Kernel >> does not use it. Existence of regulator subnode will fulfill driver's >> needs for probe. >> 2. For clocks: actually will disable these clocks because of lack of >> consumers... which is fine but probably not what you wanted. >> >> The standard approach is to add such providers when they are needed - >> there are some consumers using them. >> > OK. for now will keep the pmic clock added as clock will be in disabled > state, so it wont harm. > - will keep system related regulator like supply to arm,mif,int etc .. > will remove supplies to other peripherals IPs. Hope thats fine. You don't have to remove other regulators (these without consumers). Describe in DT all of regulators but: 1. Add to some of them consumers; 2. Disable these which are not needed (by not marking always-enabled). Just like for all other boards. Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts index 838a3626dac1..8ce04a0ec928 100644 --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts @@ -53,6 +53,355 @@ status = "okay"; }; +&hsi2c_4 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <200000>; + status = "okay"; + + s2mps15_pmic@66 { + compatible = "samsung,s2mps15-pmic"; + reg = <0x66>; + interrupts = <2 0>; + interrupt-parent = <&gpa0>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_irq>; + wakeup-source; + + s2mps15_osc: clocks { + compatible = "samsung,s2mps13-clk"; + #clock-cells = <1>; + clock-output-names = "s2mps13_ap", "s2mps13_cp", + "s2mps13_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "vdd_ldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo2_reg: LDO2 { + regulator-name = "vdd_ldo2"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <125>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "vdd_ldo3"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-always-on; + regulator-boot-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo4_reg: LDO4 { + regulator-name = "vdd_ldo4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1110000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo5_reg: LDO5 { + regulator-name = "vdd_ldo5"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo6_reg: LDO6 { + regulator-name = "vdd_ldo6"; + regulator-min-microvolt = <2250000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo7_reg: LDO7 { + regulator-name = "vdd_ldo7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo8_reg: LDO8 { + regulator-name = "vdd_ldo8"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo9_reg: LDO9 { + regulator-name = "vdd_ldo9"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo10_reg: LDO10 { + regulator-name = "vdd_ldo10"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo12_reg: LDO12 { + regulator-name = "vdd_ldo12"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo13_reg: LDO13 { + regulator-name = "vdd_ldo13"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo14_reg: LDO14 { + regulator-name = "vdd_ldo14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3375000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo15_reg: LDO15 { + regulator-name = "vdd_ldo15"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2275000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo16_reg: LDO16 { + regulator-name = "vdd_ldo16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo17_reg: LDO17 { + regulator-name = "vdd_ldo17"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3375000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo18_reg: LDO18 { + regulator-name = "vdd_ldo18"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2275000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo19_reg: LDO19 { + regulator-name = "vdd_ldo19"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3375000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo20_reg: LDO20 { + regulator-name = "vdd_ldo20"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2275000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo21_reg: LDO21 { + regulator-name = "vdd_ldo21"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3375000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo22_reg: LDO22 { + regulator-name = "vdd_ldo22"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo23_reg: LDO23 { + regulator-name = "vdd_ldo23"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2275000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo24_reg: LDO24 { + regulator-name = "vdd_ldo24"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3375000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo25_reg: LDO25 { + regulator-name = "vdd_ldo25"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3375000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo26_reg: LDO26 { + regulator-name = "vdd_ldo26"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1470000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + ldo27_reg: LDO27 { + regulator-name = "vdd_ldo27"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2275000>; + regulator-always-on; + regulator-enable-ramp-delay = <125>; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <25000>; + regulator-enable-ramp-delay = <250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_atlas"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <250>; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_apollo"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <250>; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <250>; + }; + + buck5_reg: BUCK5 { + regulator-name = "vdd_buck5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-ramp-delay = <25000>; + regulator-enable-ramp-delay = <250>; + }; + + buck6_reg: BUCK6 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <250>; + }; + + buck7_reg: BUCK7 { + regulator-name = "vdd_buck7"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <25000>; + regulator-enable-ramp-delay = <250>; + }; + + buck8_reg: BUCK8 { + regulator-name = "vdd_buck8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <25000>; + regulator-enable-ramp-delay = <250>; + }; + + buck9_reg: BUCK9 { + regulator-name = "vdd_buck9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <25000>; + regulator-enable-ramp-delay = <250>; + }; + + buck10_reg: BUCK10 { + regulator-name = "vdd_buck10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <25000>; + regulator-enable-ramp-delay = <250>; + }; + }; + }; +}; + +&pinctrl_alive { + pmic_irq: pmic-irq { + samsung,pins = "gpa0-2"; + samsung,pin-pud = <3>; + samsung,pin-drv = <3>; + }; +}; + &mmc_0 { status = "okay"; num-slots = <1>;