@@ -14,6 +14,7 @@ addressed by the host system using different I2C slave addresses.
This document describes bindings for main device node. Optional sub-blocks
must be a sub-nodes to it. Bindings for them can be found in:
- bindings/regulator/samsung,s2mps11.txt
+ - bindings/regulator/samsung,s5m8767.txt
- bindings/clock/samsung,s2mps11.txt
@@ -23,7 +24,8 @@ Required properties:
- "samsung,s2mps13-pmic",
- "samsung,s2mps14-pmic",
- "samsung,s2mps15-pmic",
- - "samsung,s2mpu02-pmic".
+ - "samsung,s2mpu02-pmic",
+ - "samsung,s5m8767-pmic".
- reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
Optional properties:
similarity index 34%
rename from Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
rename to Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt
@@ -1,98 +1,80 @@
-* Samsung S5M8767 Voltage and Current Regulator
-
-The Samsung S5M8767 is a multi-function device which includes voltage and
-current regulators, rtc, charger controller and other sub-blocks. It is
-interfaced to the host controller using a i2c interface. Each sub-block is
-addressed by the host system using different i2c slave address. This document
-describes the bindings for 'pmic' sub-block of s5m8767.
-
-Required properties:
-- compatible: Should be "samsung,s5m8767-pmic".
-- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
-
-- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
- units for buck2 when changing voltage using gpio dvs. Refer to [1] below
- for additional information.
-
-- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
- units for buck3 when changing voltage using gpio dvs. Refer to [1] below
- for additional information.
-
-- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
- units for buck4 when changing voltage using gpio dvs. Refer to [1] below
- for additional information.
-
-- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
- for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
-
-[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
- property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
- property should specify atleast one voltage level (which would be a
- safe operating voltage).
-
- If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
- property is specified, then all the eight voltage values for the
- 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
-
-Optional properties:
-- interrupt-parent: Specifies the phandle of the interrupt controller to which
- the interrupts from s5m8767 are delivered to.
-- interrupts: Interrupt specifiers for two interrupt sources.
- - First interrupt specifier is for 'irq1' interrupt.
- - Second interrupt specifier is for 'alert' interrupt.
-- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
-- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
-- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
+Binding for Samsung S5M8767 regulator block
+===========================================
+
+This is a part of device tree bindings for S5M family multi-function devices.
+More information can be found in bindings/mfd/sec-core.txt file.
+
+The S5M8767 device provide buck and LDO regulators.
+
+To register these with regulator framework instantiate under main device node
+a sub-node named "regulators" with more sub-nodes for each regulator using the
+common regulator binding documented in:
+ - Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+Required properties of the main device node (the parent!):
+ - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+ units for buck2 when changing voltage using gpio dvs. Refer to [1] below
+ for additional information.
+
+ - s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+ units for buck3 when changing voltage using gpio dvs. Refer to [1] below
+ for additional information.
+
+ - s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+ units for buck4 when changing voltage using gpio dvs. Refer to [1] below
+ for additional information.
+
+ - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
+ for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
+
+ [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
+ property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
+ property should specify atleast one voltage level (which would be a
+ safe operating voltage).
+
+ If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
+ property is specified, then all the eight voltage values for the
+ 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
+
+Optional properties of the main device node (the parent!):
+ - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
+ - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
+ - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
Additional properties required if either of the optional properties are used:
-- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
- the possible 8 options selectable by the dvs gpios. The value of this
- property should be between 0 and 7. If not specified or if out of range, the
- default value of this property is set to 0.
-
-- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
- for dvs. The format of the gpio specifier depends in the gpio controller.
-
-Regulators: The regulators of s5m8767 that have to be instantiated should be
-included in a sub-node named 'regulators'. Regulator nodes included in this
-sub-node should be of the format as listed below.
-
- regulator_name {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_1.0V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
- };
-The above regulator entries are defined in regulator bindings documentation
-except these properties:
- - op_mode: describes the different operating modes of the LDO's with
- power mode change in SOC. The different possible values are,
- 0 - always off mode
- 1 - on in normal mode
- 2 - low power mode
- 3 - suspend mode
- - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
- GPIO controlling this regulator (enable/disable); This is
- valid only for buck9.
-
-The following are the names of the regulators that the s5m8767 pmic block
-supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
-as per the datasheet of s5m8767.
+ - s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
+ the possible 8 options selectable by the dvs gpios. The value of this
+ property should be between 0 and 7. If not specified or if out of range, the
+ default value of this property is set to 0.
+
+ - s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
+ for dvs. The format of the gpio specifier depends in the gpio controller.
+
+Names of regulators supported by S5M8767 device:
- LDOn
- valid values for n are 1 to 28
- Example: LDO1, LDO2, LDO28
- BUCKn
- valid values for n are 1 to 9.
- Example: BUCK1, BUCK2, BUCK9
-
-The bindings inside the regulator nodes use the standard regulator bindings
-which are documented elsewhere.
+Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of device.
+
+
+Optional properties of the nodes under "regulators" sub-node:
+ - op_mode: describes the different operating modes of the LDO's with
+ power mode change in SOC. The different possible values are,
+ 0 - always off mode
+ 1 - on in normal mode
+ 2 - low power mode
+ 3 - suspend mode
+ - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
+ GPIO controlling this regulator
+ (enable/disable); This is valid only
+ for buck9.
Example:
@@ -9309,9 +9309,9 @@ F: drivers/regulator/s5m*.c
F: drivers/clk/clk-s2mps11.c
F: drivers/rtc/rtc-s5m.c
F: include/linux/mfd/samsung/
-F: Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
F: Documentation/devicetree/bindings/mfd/samsung,sec-core.txt
F: Documentation/devicetree/bindings/regulator/samsung,s2m*.txt
+F: Documentation/devicetree/bindings/regulator/samsung,s5m*.txt
F: Documentation/devicetree/bindings/clock/samsung,s2mps11.txt
SAMSUNG S5P/EXYNOS4 SOC SERIES CAMERA SUBSYSTEM DRIVERS