diff mbox

[28/37] dt-bindings: PCI: dra7xx: Add dt bindings for pci dra7xx EP mode

Message ID 1484216786-17292-29-git-send-email-kishon@ti.com (mailing list archive)
State Not Applicable
Headers show

Commit Message

Kishon Vijay Abraham I Jan. 12, 2017, 10:26 a.m. UTC
Add device tree binding documentation for pci dra7xx EP mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
 Documentation/devicetree/bindings/pci/ti-pci.txt |   37 ++++++++++++++++++----
 1 file changed, 30 insertions(+), 7 deletions(-)

Comments

Rob Herring Jan. 18, 2017, 9:45 p.m. UTC | #1
On Thu, Jan 12, 2017 at 03:56:17PM +0530, Kishon Vijay Abraham I wrote:
> Add device tree binding documentation for pci dra7xx EP mode.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  Documentation/devicetree/bindings/pci/ti-pci.txt |   37 ++++++++++++++++++----
>  1 file changed, 30 insertions(+), 7 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
> index 60e2516..62f5f59 100644
> --- a/Documentation/devicetree/bindings/pci/ti-pci.txt
> +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
> @@ -1,17 +1,22 @@
>  TI PCI Controllers
>  
>  PCIe Designware Controller
> - - compatible: Should be "ti,dra7-pcie""
> - - reg : Two register ranges as listed in the reg-names property
> - - reg-names : The first entry must be "ti-conf" for the TI specific registers
> -	       The second entry must be "rc-dbics" for the designware pcie
> -	       registers
> -	       The third entry must be "config" for the PCIe configuration space
> + - compatible: Should be "ti,dra7-pcie" for RC
> +	       Should be "ti,dra7-pcie-ep" for EP
>   - phys : list of PHY specifiers (used by generic PHY framework)
>   - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
>  	       number of PHYs as specified in *phys* property.
>   - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
>  	       where <X> is the instance number of the pcie from the HW spec.
> + - num-lanes as specified in ../designware-pcie.txt
> +
> +HOST MODE
> +=========
> + - reg : Two register ranges as listed in the reg-names property
> + - reg-names : The first entry must be "ti-conf" for the TI specific registers
> +	       The second entry must be "rc-dbics" for the designware pcie
> +	       registers
> +	       The third entry must be "config" for the PCIe configuration space
>   - interrupts : Two interrupt entries must be specified. The first one is for
>  		main interrupt line and the second for MSI interrupt line.
>   - #address-cells,
> @@ -19,13 +24,31 @@ PCIe Designware Controller
>     #interrupt-cells,
>     device_type,
>     ranges,
> -   num-lanes,
>     interrupt-map-mask,
>     interrupt-map : as specified in ../designware-pcie.txt
>  
> +DEVICE MODE
> +===========
> + - reg : Four register ranges as listed in the reg-names property
> + - reg-names : "ti-conf" for the TI specific registers
> +	       "ep_dbics" for the standard configuration registers as
> +		they are locally accessed within the DIF CS space
> +	       "ep_dbics2" for the standard configuration registers as
> +		they are locally accessed within the DIF CS2 space
> +	       "addr_space" used to map remote RC address space
> + - interrupts : one interrupt entries must be specified for main interrupt.
> + - num-ib-windows : number of inbound address translation windows
> + - num-ob-windows : number of outbound address translation windows
> +
>  Optional Property:
>   - gpios : Should be added if a gpio line is required to drive PERST# line
>  
> +NOTE: Two dt nodes should be added for each PCI controller; one for host

s/should/may/

Don't define dts source structure here. You could also have 2 files with 
each config and just include the right one for each board.

We don't want overlapping memory regions defined in DT and this kind of 
violates that, but I guess status is sufficient.

With that,

Acked-by: Rob Herring <robh@kernel.org>

> +mode and another for device mode. So in order for PCI to
> +work in host mode, EP mode dt node should be disabled and in order to PCI to
> +work in EP mode, host mode dt node should be disabled. And host mode and EP
> +mode are mutually exclusive.
> +
>  Example:
>  axi {
>  	compatible = "simple-bus";
> -- 
> 1.7.9.5
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
index 60e2516..62f5f59 100644
--- a/Documentation/devicetree/bindings/pci/ti-pci.txt
+++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
@@ -1,17 +1,22 @@ 
 TI PCI Controllers
 
 PCIe Designware Controller
- - compatible: Should be "ti,dra7-pcie""
- - reg : Two register ranges as listed in the reg-names property
- - reg-names : The first entry must be "ti-conf" for the TI specific registers
-	       The second entry must be "rc-dbics" for the designware pcie
-	       registers
-	       The third entry must be "config" for the PCIe configuration space
+ - compatible: Should be "ti,dra7-pcie" for RC
+	       Should be "ti,dra7-pcie-ep" for EP
  - phys : list of PHY specifiers (used by generic PHY framework)
  - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
 	       number of PHYs as specified in *phys* property.
  - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
 	       where <X> is the instance number of the pcie from the HW spec.
+ - num-lanes as specified in ../designware-pcie.txt
+
+HOST MODE
+=========
+ - reg : Two register ranges as listed in the reg-names property
+ - reg-names : The first entry must be "ti-conf" for the TI specific registers
+	       The second entry must be "rc-dbics" for the designware pcie
+	       registers
+	       The third entry must be "config" for the PCIe configuration space
  - interrupts : Two interrupt entries must be specified. The first one is for
 		main interrupt line and the second for MSI interrupt line.
  - #address-cells,
@@ -19,13 +24,31 @@  PCIe Designware Controller
    #interrupt-cells,
    device_type,
    ranges,
-   num-lanes,
    interrupt-map-mask,
    interrupt-map : as specified in ../designware-pcie.txt
 
+DEVICE MODE
+===========
+ - reg : Four register ranges as listed in the reg-names property
+ - reg-names : "ti-conf" for the TI specific registers
+	       "ep_dbics" for the standard configuration registers as
+		they are locally accessed within the DIF CS space
+	       "ep_dbics2" for the standard configuration registers as
+		they are locally accessed within the DIF CS2 space
+	       "addr_space" used to map remote RC address space
+ - interrupts : one interrupt entries must be specified for main interrupt.
+ - num-ib-windows : number of inbound address translation windows
+ - num-ob-windows : number of outbound address translation windows
+
 Optional Property:
  - gpios : Should be added if a gpio line is required to drive PERST# line
 
+NOTE: Two dt nodes should be added for each PCI controller; one for host
+mode and another for device mode. So in order for PCI to
+work in host mode, EP mode dt node should be disabled and in order to PCI to
+work in EP mode, host mode dt node should be disabled. And host mode and EP
+mode are mutually exclusive.
+
 Example:
 axi {
 	compatible = "simple-bus";