@@ -33,8 +33,11 @@
#define PWM_CMR 0x0
/* Bit field in CMR */
-#define PWM_CMR_CPOL (1 << 9)
-#define PWM_CMR_UPD_CDTY (1 << 10)
+#define PWM_CMR_CPOL BIT(9)
+#define PWM_CMR_UPD_CDTY BIT(10)
+#define PWM_CMR_DTHI BIT(17)
+#define PWM_CMR_DTLI BIT(18)
+#define PWM_CMR_PPM BIT(19)
#define PWM_CMR_CPRE_MSK 0xF
/* The following registers for PWM v1 */
@@ -219,16 +222,19 @@ static int atmel_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
{
struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip);
struct pwm_state cstate;
+ struct pwm_caps caps;
unsigned long cprd, cdty;
u32 pres, val;
int ret;
pwm_get_state(pwm, &cstate);
+ pwm_get_caps(chip, pwm, &caps);
if (state->enabled) {
if (cstate.enabled &&
cstate.polarity == state->polarity &&
- cstate.period == state->period) {
+ cstate.period == state->period &&
+ cstate.mode == state->mode) {
cprd = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm,
atmel_pwm->data->regs.period);
atmel_pwm_calculate_cdty(state, cprd, &cdty);
@@ -263,6 +269,18 @@ static int atmel_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
val &= ~PWM_CMR_CPOL;
else
val |= PWM_CMR_CPOL;
+
+ /* PWM mode. */
+ if (caps.modes & PWM_MODE(PUSH_PULL)) {
+ if (state->mode == PWM_MODE(PUSH_PULL)) {
+ val |= PWM_CMR_PPM | PWM_CMR_DTLI;
+ val &= ~PWM_CMR_DTHI;
+ } else {
+ val &= ~(PWM_CMR_PPM | PWM_CMR_DTLI |
+ PWM_CMR_DTHI);
+ }
+ }
+
atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val);
atmel_pwm_set_cprd_cdty(chip, pwm, cprd, cdty);
mutex_lock(&atmel_pwm->isr_lock);
@@ -315,6 +333,20 @@ static const struct atmel_pwm_data atmel_pwm_data_v2 = {
},
};
+static const struct atmel_pwm_data atmel_pwm_data_v3 = {
+ .regs = {
+ .period = PWMV2_CPRD,
+ .period_upd = PWMV2_CPRDUPD,
+ .duty = PWMV2_CDTY,
+ .duty_upd = PWMV2_CDTYUPD,
+ },
+ .caps = {
+ .modes = PWM_MODE(NORMAL) |
+ PWM_MODE(COMPLEMENTARY) |
+ PWM_MODE(PUSH_PULL),
+ },
+};
+
static const struct platform_device_id atmel_pwm_devtypes[] = {
{
.name = "at91sam9rl-pwm",
@@ -337,7 +369,7 @@ static const struct of_device_id atmel_pwm_dt_ids[] = {
.data = &atmel_pwm_data_v2,
}, {
.compatible = "atmel,sama5d2-pwm",
- .data = &atmel_pwm_data_v2,
+ .data = &atmel_pwm_data_v3,
}, {
/* sentinel */
},
Add support for PWM push-pull mode. This is only supported by SAMA5D2 SoCs. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> --- drivers/pwm/pwm-atmel.c | 40 ++++++++++++++++++++++++++++++++++++---- 1 file changed, 36 insertions(+), 4 deletions(-)