deleted file mode 100644
@@ -1,58 +0,0 @@
-* Samsung's I2C controller
-
-The Samsung's I2C controller is used to interface with I2C devices.
-
-Required properties:
- - compatible: value should be either of the following.
- (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
- (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
- (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
- inside HDMIPHY block found on several samsung SoCs
- (d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
- a host to SATA PHY controller on an internal bus.
- - reg: physical base address of the controller and length of memory mapped
- region.
- - interrupts: interrupt number to the cpu.
- - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
-
-Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
- - Samsung GPIO variant (deprecated):
- - gpios: The order of the gpios should be the following: <SDA, SCL>.
- The gpio specifier depends on the gpio controller. Required in all
- cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
- lines are permanently wired to the respective clienta
- - Pinctrl variant (preferred, if available):
- - pinctrl-0: Pin control group to be used for this controller.
- - pinctrl-names: Should contain only one value - "default".
-
-Optional properties:
- - samsung,i2c-slave-addr: Slave address in multi-master environment. If not
- specified, default value is 0.
- - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
- specified, the default value in Hz is 100000.
- - samsung,sysreg-phandle - handle to syscon used to control the system registers
-
-Example:
-
- i2c@13870000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x13870000 0x100>;
- interrupts = <345>;
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <100000>;
- /* Samsung GPIO variant begins here */
- gpios = <&gpd1 2 0 /* SDA */
- &gpd1 3 0 /* SCL */>;
- /* Samsung GPIO variant ends here */
- /* Pinctrl variant begins here */
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- /* Pinctrl variant ends here */
- #address-cells = <1>;
- #size-cells = <0>;
-
- wm8994@1a {
- compatible = "wlf,wm8994";
- reg = <0x1a>;
- };
- };
new file mode 100644
@@ -0,0 +1,164 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/samsung,s3c2410-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S3C/S5P/Exynos SoC I2C Controller
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+ compatible:
+ enum:
+ - samsung,s3c2410-i2c
+ - samsung,s3c2440-i2c
+ # For s3c2440-like I2C used inside HDMIPHY block found on several SoCs:
+ - samsung,s3c2440-hdmiphy-i2c
+ # For s3c2440-like I2C used as a host to SATA PHY controller on an
+ # internal bus:
+ - samsung,exynos5-sata-phy-i2c
+
+ '#address-cells':
+ const: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: i2c
+
+ gpios:
+ description: |
+ The order of the GPIOs should be the following:: <SDA, SCL>. The GPIO
+ specifier depends on the gpio controller. Required in all cases except
+ for "samsung,s3c2440-hdmiphy-i2c" whose input/output lines are
+ permanently wired to the respective client.
+ This property is deprecated. Use "pinctrl-0" and "pinctrl-names" instead.
+ deprecated: yes
+
+ interrupts:
+ maxItems: 1
+
+ reg:
+ maxItems: 1
+
+ samsung,i2c-max-bus-freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Desired frequency in Hz of the bus.
+ default: 100000
+
+ samsung,i2c-sda-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay (in ns) applied to data line (SDA) edges.
+ default: 0
+
+ samsung,i2c-slave-addr:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Slave address in multi-master environment.
+ default: 0
+
+ samsung,sysreg-phandle:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: Pandle to syscon used to control the system registers.
+
+ '#size-cells':
+ const: 0
+
+required:
+ - compatible
+ - reg
+
+allOf:
+ - $ref: /schemas/i2c/i2c-controller.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - samsung,s3c2440-hdmiphy-i2c
+ - samsung,exynos5-sata-phy-i2c
+ then:
+ properties:
+ gpios: false
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - samsung,s3c2410-i2c
+ - samsung,s3c2440-i2c
+ - samsung,s3c2440-hdmiphy-i2c
+ then:
+ required:
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/exynos5250.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ i2c@12c60000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C60000 0x100>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ samsung,i2c-slave-addr = <0x66>;
+
+ eeprom@50 {
+ compatible = "samsung,s524ad0xd1";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@12ce0000 {
+ compatible = "samsung,s3c2440-hdmiphy-i2c";
+ reg = <0x12CE0000 0x1000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_I2C_HDMI>;
+ clock-names = "i2c";
+
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
+
+ phy-i2c@38 {
+ compatible = "samsung,exynos4212-hdmiphy";
+ reg = <0x38>;
+ };
+ };
+
+ i2c@121d0000 {
+ compatible = "samsung,exynos5-sata-phy-i2c";
+ reg = <0x121D0000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clock CLK_SATA_PHYI2C>;
+ clock-names = "i2c";
+
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <40000>;
+
+ phy-i2c@38 {
+ compatible = "samsung,exynos-sataphy-i2c";
+ reg = <0x38>;
+ };
+ };
Convert the Samsung S3C24xx/S3C64xx/S5PV210/Exynos SoC I2C Controller bindings to DT schema format. The conversion includes also changes/fixes to the bindings, matching the real hardware and existing Linux driver: 1. Do not require interrupts on samsung,exynos5-sata-phy-i2c, because there is no such. 2. Do not allow gpios on samsung,exynos5-sata-phy-i2c, because they are hard-wired just like for HDMI phy. 3. Do not require samsung,i2c-sda-delay and use default of 0. 4. Require clock, which was always required but missing in bindings. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> --- .../devicetree/bindings/i2c/i2c-s3c2410.txt | 58 ------- .../bindings/i2c/samsung,s3c2410-i2c.yaml | 164 ++++++++++++++++++ 2 files changed, 164 insertions(+), 58 deletions(-) delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt create mode 100644 Documentation/devicetree/bindings/i2c/samsung,s3c2410-i2c.yaml