| Message ID | 4a407cd6-020c-1750-019a-6c0ceb40e245@users.sourceforge.net (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
Hi Markus, As I already commented on your other patch related to extcon-max14577, this patch might remove the redundant error message. But, it makes the code more complicated in side of readability. I prefer existing code. On 2017년 10월 22일 22:40, SF Markus Elfring wrote: > From: Markus Elfring <elfring@users.sourceforge.net> > Date: Sun, 22 Oct 2017 15:33:06 +0200 > > Adjust jump targets so that a bit of exception handling can be better > reused at the end of this function. > > This issue was detected by using the Coccinelle software. > > Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> > --- > drivers/devfreq/exynos-bus.c | 21 ++++++++++----------- > 1 file changed, 10 insertions(+), 11 deletions(-) > > diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c > index 49f68929e024..e38d456b2d7d 100644 > --- a/drivers/devfreq/exynos-bus.c > +++ b/drivers/devfreq/exynos-bus.c > @@ -124,34 +124,33 @@ static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags) > > if (old_freq < new_freq) { > ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol); > - if (ret < 0) { > - dev_err(bus->dev, "failed to set voltage\n"); > - goto out; > - } > + if (ret < 0) > + goto report_failure; > } > > ret = clk_set_rate(bus->clk, new_freq); > if (ret < 0) { > dev_err(dev, "failed to change clock of bus\n"); > clk_set_rate(bus->clk, old_freq); > - goto out; > + goto unlock; > } > > if (old_freq > new_freq) { > ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol); > - if (ret < 0) { > - dev_err(bus->dev, "failed to set voltage\n"); > - goto out; > - } > + if (ret < 0) > + goto report_failure; > } > bus->curr_freq = new_freq; > > dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n", > old_freq, new_freq, clk_get_rate(bus->clk)); > -out: > +unlock: > mutex_unlock(&bus->lock); > - > return ret; > + > +report_failure: > + dev_err(bus->dev, "failed to set voltage\n"); > + goto unlock; > } > > static int exynos_bus_get_dev_status(struct device *dev, >
> As I already commented on your other patch related to extcon-max14577, > this patch might remove the redundant error message. I hope that more software improvements can be achieved in this design direction. > But, it makes the code more complicated in side of readability. I prefer existing code. I prefer to avoid duplicated code a bit more. Regards, Markus -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c index 49f68929e024..e38d456b2d7d 100644 --- a/drivers/devfreq/exynos-bus.c +++ b/drivers/devfreq/exynos-bus.c @@ -124,34 +124,33 @@ static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags) if (old_freq < new_freq) { ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol); - if (ret < 0) { - dev_err(bus->dev, "failed to set voltage\n"); - goto out; - } + if (ret < 0) + goto report_failure; } ret = clk_set_rate(bus->clk, new_freq); if (ret < 0) { dev_err(dev, "failed to change clock of bus\n"); clk_set_rate(bus->clk, old_freq); - goto out; + goto unlock; } if (old_freq > new_freq) { ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol); - if (ret < 0) { - dev_err(bus->dev, "failed to set voltage\n"); - goto out; - } + if (ret < 0) + goto report_failure; } bus->curr_freq = new_freq; dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n", old_freq, new_freq, clk_get_rate(bus->clk)); -out: +unlock: mutex_unlock(&bus->lock); - return ret; + +report_failure: + dev_err(bus->dev, "failed to set voltage\n"); + goto unlock; } static int exynos_bus_get_dev_status(struct device *dev,