@@ -1673,6 +1673,7 @@ struct aac_dev
struct aac_hba_map_info hba_map[AAC_MAX_BUSES][AAC_MAX_TARGETS];
u8 adapter_shutdown;
u32 handle_pci_error;
+ bool init_reset;
};
#define aac_adapter_interrupt(dev) \
@@ -1680,6 +1680,9 @@ static int aac_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
aac->cardtype = index;
INIT_LIST_HEAD(&aac->entry);
+ if (aac_reset_devices || reset_devices)
+ aac->init_reset = true;
+
aac->fibs = kzalloc(sizeof(struct fib) * (shost->can_queue + AAC_NUM_MGT_FIB), GFP_KERNEL);
if (!aac->fibs)
goto out_free_host;
@@ -561,11 +561,16 @@ int _aac_rx_init(struct aac_dev *dev)
dev->a_ops.adapter_sync_cmd = rx_sync_cmd;
dev->a_ops.adapter_enable_int = aac_rx_disable_interrupt;
dev->OIMR = status = rx_readb (dev, MUnit.OIMR);
- if ((((status & 0x0c) != 0x0c) || aac_reset_devices || reset_devices) &&
- !aac_rx_restart_adapter(dev, 0, IOP_HWSOFT_RESET))
- /* Make sure the Hardware FIFO is empty */
- while ((++restart < 512) &&
- (rx_readl(dev, MUnit.OutboundQueue) != 0xFFFFFFFFL));
+
+ if (((status & 0x0c) != 0x0c) || dev->init_reset) {
+ dev->init_reset = false;
+ if (!aac_rx_restart_adapter(dev, 0, IOP_HWSOFT_RESET)) {
+ /* Make sure the Hardware FIFO is empty */
+ while ((++restart < 512) &&
+ (rx_readl(dev, MUnit.OutboundQueue) != 0xFFFFFFFFL));
+ }
+ }
+
/*
* Check to see if the board panic'd while booting.
*/
@@ -868,9 +868,13 @@ int aac_src_init(struct aac_dev *dev)
/* Failure to reset here is an option ... */
dev->a_ops.adapter_sync_cmd = src_sync_cmd;
dev->a_ops.adapter_enable_int = aac_src_disable_interrupt;
- if ((aac_reset_devices || reset_devices) &&
- !aac_src_restart_adapter(dev, 0, IOP_HWSOFT_RESET))
- ++restart;
+
+ if (dev->init_reset) {
+ dev->init_reset = false;
+ if (!aac_src_restart_adapter(dev, 0, IOP_HWSOFT_RESET))
+ ++restart;
+ }
+
/*
* Check to see if the board panic'd while booting.
*/
@@ -1014,9 +1018,13 @@ int aac_srcv_init(struct aac_dev *dev)
/* Failure to reset here is an option ... */
dev->a_ops.adapter_sync_cmd = src_sync_cmd;
dev->a_ops.adapter_enable_int = aac_src_disable_interrupt;
- if ((aac_reset_devices || reset_devices) &&
- !aac_src_restart_adapter(dev, 0, IOP_HWSOFT_RESET))
- ++restart;
+
+ if (dev->init_reset) {
+ dev->init_reset = false;
+ if (!aac_src_restart_adapter(dev, 0, IOP_HWSOFT_RESET))
+ ++restart;
+ }
+
/*
* Check to see if flash update is running.
* Wait for the adapter to be up and running. Wait up to 5 minutes
Currently the driver accepts two ways of requesting an initialization reset on the adapter: by passing aac_reset_devices module parameter, or the generic kernel parameter reset_devices. It's working as intended...but if we end up reaching a scsi hang and the scsi EH mechanism takes place, aacraid performs resets as part of the scsi error recovery procedure. These EH routines might reinitialize the device, and if we have provided some of the reset parameters in the kernel command-line, we again perform an "initialization" reset. So, to avoid this duplication of resets in case of scsi EH path, this patch adds a field to aac_dev struct to keep per-adapter track of the init reset request - once it's done, we set it to false and don't proactively reset anymore in case of reinitializations. Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> --- drivers/scsi/aacraid/aacraid.h | 1 + drivers/scsi/aacraid/linit.c | 3 +++ drivers/scsi/aacraid/rx.c | 15 ++++++++++----- drivers/scsi/aacraid/src.c | 20 ++++++++++++++------ 4 files changed, 28 insertions(+), 11 deletions(-)