@@ -4935,6 +4935,7 @@ lpfc_fcp_imax_store(struct device *dev, struct device_attribute *attr,
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *)shost->hostdata;
struct lpfc_hba *phba = vport->phba;
+ uint32_t usdelay;
int val = 0, i;
/* fcp_imax is only valid for SLI4 */
@@ -4958,9 +4959,14 @@ lpfc_fcp_imax_store(struct device *dev, struct device_attribute *attr,
phba->cfg_fcp_imax = (uint32_t)val;
phba->initial_imax = phba->cfg_fcp_imax;
+ if (phba->cfg_fcp_imax)
+ usdelay = LPFC_SEC_TO_USEC / phba->cfg_fcp_imax;
+ else
+ usdelay = 0;
+
for (i = 0; i < phba->cfg_irq_chann; i += LPFC_MAX_EQ_DELAY_EQID_CNT)
lpfc_modify_hba_eq_delay(phba, i, LPFC_MAX_EQ_DELAY_EQID_CNT,
- val);
+ usdelay);
return strlen(buf);
}
@@ -9333,7 +9333,7 @@ lpfc_sli4_queue_setup(struct lpfc_hba *phba)
struct lpfc_sli4_hdw_queue *qp;
LPFC_MBOXQ_t *mboxq;
int qidx;
- uint32_t length;
+ uint32_t length, usdelay;
int rc = -ENOMEM;
/* Check for dual-ULP support */
@@ -9640,10 +9640,15 @@ lpfc_sli4_queue_setup(struct lpfc_hba *phba)
phba->sli4_hba.dat_rq->queue_id,
phba->sli4_hba.els_cq->queue_id);
+ if (phba->cfg_fcp_imax)
+ usdelay = LPFC_SEC_TO_USEC / phba->cfg_fcp_imax;
+ else
+ usdelay = 0;
+
for (qidx = 0; qidx < phba->cfg_irq_chann;
qidx += LPFC_MAX_EQ_DELAY_EQID_CNT)
lpfc_modify_hba_eq_delay(phba, qidx, LPFC_MAX_EQ_DELAY_EQID_CNT,
- phba->cfg_fcp_imax);
+ usdelay);
if (phba->sli4_hba.cq_max) {
kfree(phba->sli4_hba.cq_lookup);
@@ -14425,43 +14425,86 @@ lpfc_dual_chute_pci_bar_map(struct lpfc_hba *phba, uint16_t pci_barset)
}
/**
- * lpfc_modify_hba_eq_delay - Modify Delay Multiplier on FCP EQs
- * @phba: HBA structure that indicates port to create a queue on.
- * @startq: The starting FCP EQ to modify
- *
- * This function sends an MODIFY_EQ_DELAY mailbox command to the HBA.
- * The command allows up to LPFC_MAX_EQ_DELAY_EQID_CNT EQ ID's to be
- * updated in one mailbox command.
- *
- * The @phba struct is used to send mailbox command to HBA. The @startq
- * is used to get the starting FCP EQ to change.
- * This function is asynchronous and will wait for the mailbox
- * command to finish before continuing.
- *
- * On success this function will return a zero. If unable to allocate enough
- * memory this function will return -ENOMEM. If the queue create mailbox command
- * fails this function will return -ENXIO.
+ * lpfc_modify_hba_eq_delay - Modify Delay Multiplier on EQs
+ * @phba: HBA structure that EQs are on.
+ * @startq: The starting EQ index to modify
+ * @numq: The number of EQs (consecutive indexes) to modify
+ * @usdelay: amount of delay
+ *
+ * This function revises the EQ delay on 1 or more EQs. The EQ delay
+ * is set either by writing to a register (if supported by the SLI Port)
+ * or by mailbox command. The mailbox command allows several EQs to be
+ * updated at once.
+ *
+ * The @phba struct is used to send a mailbox command to HBA. The @startq
+ * is used to get the starting EQ index to change. The @numq value is
+ * used to specify how many consecutive EQ indexes, starting at EQ index,
+ * are to be changed. This function is asynchronous and will wait for any
+ * mailbox commands to finish before returning.
+ *
+ * On success this function will return a zero. If unable to allocate
+ * enough memory this function will return -ENOMEM. If a mailbox command
+ * fails this function will return -ENXIO. Note: on ENXIO, some EQs may
+ * have had their delay multipler changed.
**/
-int
+void
lpfc_modify_hba_eq_delay(struct lpfc_hba *phba, uint32_t startq,
- uint32_t numq, uint32_t imax)
+ uint32_t numq, uint32_t usdelay)
{
struct lpfc_mbx_modify_eq_delay *eq_delay;
LPFC_MBOXQ_t *mbox;
struct lpfc_queue *eq;
- int cnt, rc, length, status = 0;
+ int cnt = 0, rc, length;
uint32_t shdr_status, shdr_add_status;
- uint32_t result, val;
+ uint32_t dmult;
+ struct lpfc_register reg_data;
int qidx;
union lpfc_sli4_cfg_shdr *shdr;
- uint16_t dmult;
if (startq >= phba->cfg_irq_chann)
- return 0;
+ return;
+
+ if (usdelay > 0xFFFF) {
+ lpfc_printf_log(phba, KERN_INFO, LOG_INIT | LOG_FCP | LOG_NVME,
+ "6429 usdelay %d too large. Scaled down to "
+ "0xFFFF.\n", usdelay);
+ usdelay = 0xFFFF;
+ }
+
+ /* set values by EQ_DELAY register if supported */
+ if (phba->sli.sli_flag & LPFC_SLI_USE_EQDR) {
+ for (qidx = startq; qidx < phba->cfg_irq_chann; qidx++) {
+ eq = phba->sli4_hba.hdwq[qidx].hba_eq;
+ if (!eq)
+ continue;
+
+ /* save value last set */
+ eq->q_mode = usdelay;
+
+ /* write register */
+ reg_data.word0 = 0;
+ bf_set(lpfc_sliport_eqdelay_id, ®_data,
+ eq->queue_id);
+ bf_set(lpfc_sliport_eqdelay_delay, ®_data, usdelay);
+ writel(reg_data.word0,
+ phba->sli4_hba.u.if_type2.EQDregaddr);
+
+ if (++cnt >= numq)
+ break;
+ }
+
+ return;
+ }
+
+ /* Otherwise, set values by mailbox cmd */
mbox = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
- if (!mbox)
- return -ENOMEM;
+ if (!mbox) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT | LOG_FCP | LOG_NVME,
+ "6428 Failed allocating mailbox cmd buffer."
+ " EQ delay was not set.\n");
+ return;
+ }
length = (sizeof(struct lpfc_mbx_modify_eq_delay) -
sizeof(struct lpfc_sli4_cfg_mhdr));
lpfc_sli4_config(phba, mbox, LPFC_MBOX_SUBSYSTEM_COMMON,
@@ -14470,44 +14513,22 @@ lpfc_modify_hba_eq_delay(struct lpfc_hba *phba, uint32_t startq,
eq_delay = &mbox->u.mqe.un.eq_delay;
/* Calculate delay multiper from maximum interrupt per second */
- result = imax / phba->cfg_irq_chann;
- if (result > LPFC_DMULT_CONST || result == 0)
- dmult = 0;
- else
- dmult = LPFC_DMULT_CONST/result - 1;
+ dmult = (usdelay * LPFC_DMULT_CONST) / LPFC_SEC_TO_USEC;
+ if (dmult)
+ dmult--;
if (dmult > LPFC_DMULT_MAX)
dmult = LPFC_DMULT_MAX;
- cnt = 0;
for (qidx = startq; qidx < phba->cfg_irq_chann; qidx++) {
eq = phba->sli4_hba.hdwq[qidx].hba_eq;
if (!eq)
continue;
- eq->q_mode = imax;
+ eq->q_mode = usdelay;
eq_delay->u.request.eq[cnt].eq_id = eq->queue_id;
eq_delay->u.request.eq[cnt].phase = 0;
eq_delay->u.request.eq[cnt].delay_multi = dmult;
- cnt++;
-
- /* q_mode is only used for auto_imax */
- if (phba->sli.sli_flag & LPFC_SLI_USE_EQDR) {
- /* Use EQ Delay Register method for q_mode */
-
- /* Convert for EQ Delay register */
- val = phba->cfg_fcp_imax;
- if (val) {
- /* First, interrupts per sec per EQ */
- val = phba->cfg_fcp_imax / phba->cfg_irq_chann;
-
- /* us delay between each interrupt */
- val = LPFC_SEC_TO_USEC / val;
- }
- eq->q_mode = val;
- } else {
- eq->q_mode = imax;
- }
- if (cnt >= numq)
+ if (++cnt >= numq)
break;
}
eq_delay->u.request.num_eq = cnt;
@@ -14525,10 +14546,9 @@ lpfc_modify_hba_eq_delay(struct lpfc_hba *phba, uint32_t startq,
"2512 MODIFY_EQ_DELAY mailbox failed with "
"status x%x add_status x%x, mbx status x%x\n",
shdr_status, shdr_add_status, rc);
- status = -ENXIO;
}
mempool_free(mbox, phba->mbox_mem_pool);
- return status;
+ return;
}
/**
@@ -956,8 +956,8 @@ struct lpfc_queue *lpfc_sli4_queue_alloc(struct lpfc_hba *, uint32_t,
uint32_t, uint32_t);
void lpfc_sli4_queue_free(struct lpfc_queue *);
int lpfc_eq_create(struct lpfc_hba *, struct lpfc_queue *, uint32_t);
-int lpfc_modify_hba_eq_delay(struct lpfc_hba *phba, uint32_t startq,
- uint32_t numq, uint32_t imax);
+void lpfc_modify_hba_eq_delay(struct lpfc_hba *phba, uint32_t startq,
+ uint32_t numq, uint32_t usdelay);
int lpfc_cq_create(struct lpfc_hba *, struct lpfc_queue *,
struct lpfc_queue *, uint32_t, uint32_t);
int lpfc_cq_create_set(struct lpfc_hba *phba, struct lpfc_queue **cqp,