diff mbox series

[6/7] mpi3mr: nvme pass-through support

Message ID 20210921184600.64427-7-kashyap.desai@broadcom.com (mailing list archive)
State New
Headers show
Series adding application support | expand

Commit Message

Kashyap Desai Sept. 21, 2021, 6:45 p.m. UTC
This patch adds support in the mpi3mr drive for management applications to
send an MPI3 EncapsulatedNVMe passthru commands to the NVMe devices
attached to the avenger series of tri-mode controller. Since the NVMe
drives are exposed as SCSI drives by the controller the standard NVMe
applications cannot be used to interact with the drives and the command
sets supported is also limited by the controller firmware. Special
handling is required for MPI3 EncapsulatedNVMe passthru commands for
PRP/SGL setup in the commands hence the additional changes.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>

Cc: sathya.prakash@broadcom.com
---
 drivers/scsi/mpi3mr/mpi3mr.h     |   8 +
 drivers/scsi/mpi3mr/mpi3mr_app.c | 346 ++++++++++++++++++++++++++++++-
 drivers/scsi/mpi3mr/mpi3mr_app.h |  27 +++
 3 files changed, 380 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/drivers/scsi/mpi3mr/mpi3mr.h b/drivers/scsi/mpi3mr/mpi3mr.h
index 6108fe562bed..289aaaec7ee2 100644
--- a/drivers/scsi/mpi3mr/mpi3mr.h
+++ b/drivers/scsi/mpi3mr/mpi3mr.h
@@ -45,6 +45,7 @@ 
 #include "mpi/mpi30_init.h"
 #include "mpi/mpi30_ioc.h"
 #include "mpi/mpi30_sas.h"
+#include "mpi/mpi30_pci.h"
 #include "mpi3mr_debug.h"
 
 /* Global list and lock for storing multiple adapters managed by the driver */
@@ -699,6 +700,9 @@  struct scmd_priv {
  * @block_ioctls: Block IOCTL flag
  * @reset_mutex: Controller reset mutex
  * @reset_waitq: Controller reset  wait queue
+ * @prp_list_virt: NVMe encapsulated PRP list virtual base
+ * @prp_list_virt_dma: NVMe encapsulated PRP list DMA
+ * @prp_sz: NVME encapsulated PRP list size
  * @diagsave_timeout: Diagnostic information save timeout
  * @logging_level: Controller debug logging level
  * @flush_io_count: I/O count to flush after reset
@@ -840,6 +844,10 @@  struct mpi3mr_ioc {
 	struct mutex reset_mutex;
 	wait_queue_head_t reset_waitq;
 
+	void *prp_list_virt;
+	dma_addr_t prp_list_virt_dma;
+	u32 prp_sz;
+
 	u16 diagsave_timeout;
 	int logging_level;
 	u16 flush_io_count;
diff --git a/drivers/scsi/mpi3mr/mpi3mr_app.c b/drivers/scsi/mpi3mr/mpi3mr_app.c
index f8e7d2713fe4..0ecdf02c10c5 100644
--- a/drivers/scsi/mpi3mr/mpi3mr_app.c
+++ b/drivers/scsi/mpi3mr/mpi3mr_app.c
@@ -591,6 +591,315 @@  static void mpi3mr_ioctl_build_sgl(u8 *mpi_req, uint32_t sgl_offset,
 	}
 }
 
+/**
+ * mpi3mr_get_nvme_data_fmt - returns the NVMe data format
+ * @nvme_encap_request: NVMe encapsulated MPI request
+ *
+ * This function returns the type of the data format specified
+ * in user provided NVMe command in NVMe encapsulated request.
+ *
+ * Return: Data format of the NVMe command (PRP/SGL etc)
+ */
+static u8 mpi3mr_get_nvme_data_fmt(
+	struct mpi3_nvme_encapsulated_request *nvme_encap_request)
+{
+	return (u8)((nvme_encap_request->command[0] & 0xc000) >> 14);
+}
+
+/**
+ * mpi3mr_build_nvme_sgl - SGL constructor for NVME
+ *				   encapsulated request
+ * @mrioc: Adapter instance reference
+ * @nvme_encap_request: NVMe encapsulated MPI request
+ * @dma_buffers: DMA address of the buffers to be placed in sgl
+ * @bufcnt: Number of DMA buffers
+ *
+ * This function places the DMA address of the given buffers in
+ * proper format as SGEs in the given NVMe encapsulated request.
+ *
+ * Return: 0 on success, -1 on failure
+ */
+static int mpi3mr_build_nvme_sgl(struct mpi3mr_ioc *mrioc,
+	struct mpi3_nvme_encapsulated_request *nvme_encap_request,
+	struct mpi3mr_buf_map *dma_buffers, u8 bufcnt)
+{
+	struct mpi3mr_nvme_pt_sge *nvme_sgl;
+	u64 sgl_ptr, sgemod_mask, sgemod_val;
+	u8 count;
+	size_t length = 0;
+	struct mpi3mr_buf_map *dma_buff = dma_buffers;
+
+	/*
+	 * Not all commands require a data transfer. If no data, just return
+	 * without constructing any sgl.
+	 */
+	for (count = 0; count < bufcnt; count++, dma_buff++) {
+		if ((dma_buff->data_dir == DMA_TO_DEVICE) ||
+		    (dma_buff->data_dir == DMA_FROM_DEVICE)) {
+			sgl_ptr = (u64)dma_buff->kern_buf_dma;
+			length = dma_buff->kern_buf_len;
+			break;
+		}
+	}
+	if (!length)
+		return 0;
+
+	sgemod_mask = ((u64)((mrioc->facts.sge_mod_mask) <<
+				mrioc->facts.sge_mod_shift) << 32);
+	sgemod_val = ((u64)(mrioc->facts.sge_mod_value) <<
+				mrioc->facts.sge_mod_shift) << 32;
+
+	if (sgl_ptr & sgemod_mask) {
+		dbgprint(mrioc,
+		    "%s: SGL address collides with SGE modifier\n",
+		    __func__);
+		return -1;
+	}
+
+	sgl_ptr &= ~sgemod_mask;
+	sgl_ptr |= sgemod_val;
+	nvme_sgl = (struct mpi3mr_nvme_pt_sge *)
+	    ((u8 *)(nvme_encap_request->command) + MPI3MR_NVME_CMD_SGL_OFFSET);
+	memset(nvme_sgl, 0, sizeof(struct mpi3mr_nvme_pt_sge));
+	nvme_sgl->base_addr = sgl_ptr;
+	nvme_sgl->length = length;
+
+	return 0;
+}
+
+/**
+ * mpi3mr_build_nvme_prp - PRP constructor for NVME
+ *			       encapsulated request
+ * @mrioc: Adapter instance reference
+ * @nvme_encap_request: NVMe encapsulated MPI request
+ * @dma_buffers: DMA address of the buffers to be placed in SGL
+ * @bufcnt: Number of DMA buffers
+ *
+ * This function places the DMA address of the given buffers in
+ * proper format as PRP entries in the given NVMe encapsulated
+ * request.
+ *
+ * Return: 0 on success, -1 on failure
+ */
+static int mpi3mr_build_nvme_prp(struct mpi3mr_ioc *mrioc,
+		struct mpi3_nvme_encapsulated_request *nvme_encap_request,
+		struct mpi3mr_buf_map *dma_buffers, u8 bufcnt)
+{
+	int prp_size = MPI3MR_NVME_PRP_SIZE;
+	__le64 *prp_entry, *prp1_entry, *prp2_entry, *prp_page;
+	dma_addr_t prp_entry_dma, prp_page_dma, dma_addr;
+	u32 offset, entry_len, dev_pgsz, page_mask_result, page_mask;
+	size_t length = 0;
+	u8 count;
+	struct mpi3mr_buf_map *dma_buff;
+	struct mpi3mr_tgt_dev *tgtdev;
+	u64 sgemod_mask, sgemod_val;
+	u16 dev_handle;
+
+	dma_buff = dma_buffers;
+	dev_handle = nvme_encap_request->dev_handle;
+
+	/*
+	 * Not all commands require a data transfer. If no data, just return
+	 * without constructing any PRP.
+	 */
+	for (count = 0; count < bufcnt; count++, dma_buff++) {
+		if ((dma_buff->data_dir == DMA_TO_DEVICE) ||
+		    (dma_buff->data_dir == DMA_FROM_DEVICE)) {
+			dma_addr = dma_buff->kern_buf_dma;
+			length = dma_buff->kern_buf_len;
+			break;
+		}
+	}
+	if (!length)
+		return 0;
+
+	tgtdev = mpi3mr_get_tgtdev_by_handle(mrioc, dev_handle);
+	if (!tgtdev) {
+		dbgprint(mrioc, "%s: invalid device handle 0x%04x\n",
+			__func__, dev_handle);
+		return -1;
+	}
+	if (tgtdev->dev_spec.pcie_inf.pgsz == 0) {
+		dbgprint(mrioc,
+		    "%s: NVME device page size is zero for handle 0x%04x\n",
+		    __func__, dev_handle);
+		mpi3mr_tgtdev_put(tgtdev);
+		return -1;
+	}
+	dev_pgsz = 1 << (tgtdev->dev_spec.pcie_inf.pgsz);
+	mpi3mr_tgtdev_put(tgtdev);
+
+	mrioc->prp_sz = 0;
+	mrioc->prp_list_virt = dma_alloc_coherent(&mrioc->pdev->dev,
+					dev_pgsz,
+					&mrioc->prp_list_virt_dma,
+					GFP_KERNEL);
+
+	if (!mrioc->prp_list_virt)
+		return -1;
+
+	mrioc->prp_sz = dev_pgsz;
+	/*
+	 * Set pointers to PRP1 and PRP2, which are in the NVMe command.
+	 * PRP1 is located at a 24 byte offset from the start of the NVMe
+	 * command.  Then set the current PRP entry pointer to PRP1.
+	 */
+	prp1_entry = (__le64 *)((u8 *)(nvme_encap_request->command) +
+						MPI3MR_NVME_CMD_PRP1_OFFSET);
+	prp2_entry = (__le64 *)((u8 *)(nvme_encap_request->command) +
+						MPI3MR_NVME_CMD_PRP2_OFFSET);
+	prp_entry = prp1_entry;
+	/*
+	 * For the PRP entries, use the specially allocated buffer of
+	 * contiguous memory.
+	 */
+	prp_page = (__le64 *)mrioc->prp_list_virt;
+	prp_page_dma = mrioc->prp_list_virt_dma;
+
+	/*
+	 * Check if we are within 1 entry of a page boundary we don't
+	 * want our first entry to be a PRP List entry.
+	 */
+	page_mask = dev_pgsz - 1;
+	page_mask_result = (uintptr_t)((u8 *)prp_page + prp_size) & page_mask;
+	if (!page_mask_result) {
+		ioc_err(mrioc, "%s: PRP page is not page aligned\n", __func__);
+		goto err_out;
+	}
+
+	/*
+	 * Set PRP physical pointer, which initially points to the current PRP
+	 * DMA memory page.
+	 */
+	prp_entry_dma = prp_page_dma;
+	sgemod_mask = ((u64)((mrioc->facts.sge_mod_mask) <<
+				mrioc->facts.sge_mod_shift) << 32);
+	sgemod_val = ((u64)(mrioc->facts.sge_mod_value) <<
+				mrioc->facts.sge_mod_shift) << 32;
+
+	/* Loop while the length is not zero. */
+	while (length) {
+		page_mask_result = (prp_entry_dma + prp_size) & page_mask;
+		if (!page_mask_result && (length >  dev_pgsz)) {
+			dbgprint(mrioc,
+			    "%s: single PRP page is not sufficient\n",
+			    __func__);
+			goto err_out;
+		}
+
+		/* Need to handle if entry will be part of a page. */
+		offset = dma_addr & page_mask;
+		entry_len = dev_pgsz - offset;
+
+		if (prp_entry == prp1_entry) {
+			/*
+			 * Must fill in the first PRP pointer (PRP1) before
+			 * moving on.
+			 */
+			*prp1_entry = cpu_to_le64(dma_addr);
+			if (*prp1_entry & sgemod_mask) {
+				dbgprint(mrioc,
+				    "%s: PRP1 address collides with SGE modifier\n",
+				    __func__);
+				goto err_out;
+			}
+			*prp1_entry &= ~sgemod_mask;
+			*prp1_entry |= sgemod_val;
+
+			/*
+			 * Now point to the second PRP entry within the
+			 * command (PRP2).
+			 */
+			prp_entry = prp2_entry;
+		} else if (prp_entry == prp2_entry) {
+			/*
+			 * Should the PRP2 entry be a PRP List pointer or just
+			 * a regular PRP pointer?  If there is more than one
+			 * more page of data, must use a PRP List pointer.
+			 */
+			if (length > dev_pgsz) {
+				/*
+				 * PRP2 will contain a PRP List pointer because
+				 * more PRP's are needed with this command. The
+				 * list will start at the beginning of the
+				 * contiguous buffer.
+				 */
+				*prp2_entry = cpu_to_le64(prp_entry_dma);
+				if (*prp2_entry & sgemod_mask) {
+					dbgprint(mrioc,
+					    "%s: PRP list address collides with SGE modifier\n",
+					    __func__);
+					goto err_out;
+				}
+				*prp2_entry &= ~sgemod_mask;
+				*prp2_entry |= sgemod_val;
+
+				/*
+				 * The next PRP Entry will be the start of the
+				 * first PRP List.
+				 */
+				prp_entry = prp_page;
+				continue;
+			} else {
+				/*
+				 * After this, the PRP Entries are complete.
+				 * This command uses 2 PRP's and no PRP list.
+				 */
+				*prp2_entry = cpu_to_le64(dma_addr);
+				if (*prp2_entry & sgemod_mask) {
+					dbgprint(mrioc,
+					    "%s: PRP2 collides with SGE modifier\n",
+					    __func__);
+					goto err_out;
+				}
+				*prp2_entry &= ~sgemod_mask;
+				*prp2_entry |= sgemod_val;
+			}
+		} else {
+			/*
+			 * Put entry in list and bump the addresses.
+			 *
+			 * After PRP1 and PRP2 are filled in, this will fill in
+			 * all remaining PRP entries in a PRP List, one per
+			 * each time through the loop.
+			 */
+			*prp_entry = cpu_to_le64(dma_addr);
+			if (*prp1_entry & sgemod_mask) {
+				dbgprint(mrioc,
+				    "%s: PRP address collides with SGE modifier\n",
+				    __func__);
+				goto err_out;
+			}
+			*prp_entry &= ~sgemod_mask;
+			*prp_entry |= sgemod_val;
+			prp_entry++;
+			prp_entry_dma++;
+		}
+
+		/*
+		 * Bump the phys address of the command's data buffer by the
+		 * entry_len.
+		 */
+		dma_addr += entry_len;
+
+		/* decrement length accounting for last partial page. */
+		if (entry_len > length)
+			length = 0;
+		else
+			length -= entry_len;
+	}
+	return 0;
+err_out:
+	if (mrioc->prp_list_virt) {
+		dma_free_coherent(&mrioc->pdev->dev, mrioc->prp_sz,
+		    mrioc->prp_list_virt, mrioc->prp_list_virt_dma);
+		mrioc->prp_list_virt = NULL;
+	}
+	return -1;
+}
+
+
 /**
  * mpi3mr_ioctl_process_mpt_cmds - MPI Pass through IOCTL handler
  * @mrioc: Adapter instance reference
@@ -622,7 +931,7 @@  static long mpi3mr_ioctl_process_mpt_cmds(struct file *file,
 	struct mpi3_status_reply_descriptor *status_desc;
 	struct mpi3mr_ioctl_reply_buf *ioctl_reply_buf = NULL;
 	u8 *mpi_req = NULL, *sense_buff_k = NULL;
-	u8 count, bufcnt, din_cnt = 0, dout_cnt = 0;
+	u8 count, bufcnt, din_cnt = 0, dout_cnt = 0, nvme_fmt;
 	u8 erb_offset = 0xFF, reply_offset = 0xFF, sg_entries = 0;
 	bool invalid_be = false, is_rmcb = false, is_rmrb = false;
 	u32 tmplen;
@@ -809,6 +1118,35 @@  static long mpi3mr_ioctl_process_mpt_cmds(struct file *file,
 		goto out;
 	}
 
+	if (mpi_header->function == MPI3_FUNCTION_NVME_ENCAPSULATED) {
+		nvme_fmt = mpi3mr_get_nvme_data_fmt(
+			(struct mpi3_nvme_encapsulated_request *)mpi_req);
+		if (nvme_fmt == MPI3MR_NVME_DATA_FORMAT_PRP) {
+			if (mpi3mr_build_nvme_prp(mrioc,
+			    (struct mpi3_nvme_encapsulated_request *)mpi_req,
+			    dma_buffers, bufcnt)) {
+				rval = -ENOMEM;
+				mutex_unlock(&mrioc->ioctl_cmds.mutex);
+				goto out;
+			}
+		} else if (nvme_fmt == MPI3MR_NVME_DATA_FORMAT_SGL1 ||
+			nvme_fmt == MPI3MR_NVME_DATA_FORMAT_SGL2) {
+			if (mpi3mr_build_nvme_sgl(mrioc,
+			    (struct mpi3_nvme_encapsulated_request *)mpi_req,
+			    dma_buffers, bufcnt)) {
+				rval = -EINVAL;
+				mutex_unlock(&mrioc->ioctl_cmds.mutex);
+				goto out;
+			}
+		} else {
+			dbgprint(mrioc,
+			    "%s:invalid NVMe command format\n", __func__);
+			rval = -EINVAL;
+			mutex_unlock(&mrioc->ioctl_cmds.mutex);
+			goto out;
+		}
+	}
+
 	mrioc->ioctl_cmds.state = MPI3MR_CMD_PENDING;
 	mrioc->ioctl_cmds.is_waiting = 1;
 	mrioc->ioctl_cmds.callback = NULL;
@@ -834,6 +1172,12 @@  static long mpi3mr_ioctl_process_mpt_cmds(struct file *file,
 		goto out_unlock;
 	}
 
+	if (mrioc->prp_list_virt) {
+		dma_free_coherent(&mrioc->pdev->dev, mrioc->prp_sz,
+		    mrioc->prp_list_virt, mrioc->prp_list_virt_dma);
+		mrioc->prp_list_virt = NULL;
+	}
+
 	if ((mrioc->ioctl_cmds.ioc_status & MPI3_IOCSTATUS_STATUS_MASK)
 	     != MPI3_IOCSTATUS_SUCCESS) {
 		dbgprint(mrioc,
diff --git a/drivers/scsi/mpi3mr/mpi3mr_app.h b/drivers/scsi/mpi3mr/mpi3mr_app.h
index ec714d210b9e..65ad2f9f3fbe 100644
--- a/drivers/scsi/mpi3mr/mpi3mr_app.h
+++ b/drivers/scsi/mpi3mr/mpi3mr_app.h
@@ -108,6 +108,33 @@  struct mpi3mr_adp_info {
 	struct mpi3_driver_info_layout driver_info;
 };
 
+/* Encapsulated NVMe command definitions */
+#define	MPI3MR_NVME_PRP_SIZE		8 /* PRP size */
+#define	MPI3MR_NVME_CMD_PRP1_OFFSET	24 /* PRP1 offset in NVMe cmd */
+#define	MPI3MR_NVME_CMD_PRP2_OFFSET	32 /* PRP2 offset in NVMe cmd */
+#define	MPI3MR_NVME_CMD_SGL_OFFSET	24 /* SGL offset in NVMe cmd */
+#define MPI3MR_NVME_DATA_FORMAT_PRP	0
+#define MPI3MR_NVME_DATA_FORMAT_SGL1	1
+#define MPI3MR_NVME_DATA_FORMAT_SGL2	2
+
+/**
+ * struct mpi3mr_nvme_pt_sge -  Structure to store SGEs for NVMe
+ * Encapsulated commands.
+ *
+ * @base_addr: Physical address
+ * @length: SGE length
+ * @rsvd: Reserved
+ * @rsvd1: Reserved
+ * @sgl_type: sgl type
+ */
+struct mpi3mr_nvme_pt_sge {
+	u64 base_addr;
+	u32 length;
+	u16 rsvd;
+	u8 rsvd1;
+	u8 sgl_type;
+};
+
 /**
  * struct mpi3mr_buf_map -  local structure to
  * track kernel and user buffers associated with an IOCTL