diff mbox series

scsi: megaraid: Fix uninitialized mbox in mega_cmd_done

Message ID 20230531133259.55619-1-mheyne@amazon.de (mailing list archive)
State Changes Requested
Headers show
Series scsi: megaraid: Fix uninitialized mbox in mega_cmd_done | expand

Commit Message

Maximilian Heyne May 31, 2023, 1:32 p.m. UTC
This is similar to commit 7a2ae008a53c ("scsi: megaraid: Fix
mega_cmd_done() CMDID_INT_CMDS"). When cmdid == CMDID_INT_CMDS and
status != 0 then mbox is still NULL but is dereferenced below.

This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.

Fixes: 0f2bb84d2a68 ("[SCSI] megaraid: simplify internal command handling")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
---
Note: I have only compile tested this commit. Haven't tried reproducing it.

 drivers/scsi/megaraid.c | 1 +
 1 file changed, 1 insertion(+)

Comments

Martin K. Petersen May 31, 2023, 10:38 p.m. UTC | #1
Hi Maximilian!

> This is similar to commit 7a2ae008a53c ("scsi: megaraid: Fix
> mega_cmd_done() CMDID_INT_CMDS").

That's supposed to be commit 75cb113cd43f, right?

> When cmdid == CMDID_INT_CMDS and status != 0 then mbox is still NULL
> but is dereferenced below.

Is this actually a valid scenario, though? The mbox is only dereferenced
if there is status returned from an attached device. And I am guessing
that a controller-internal command does not talk to any attached device.
Thus status should always be 0 for CMDID_INT_CMDS. I don't have the
megaraid firmware manual so this is pure guesswork on my part. But you
would think we would have come across an invalid deref since the
original 2014 commit made the offending change.
Maximilian Heyne June 1, 2023, 7:23 a.m. UTC | #2
On Wed, May 31, 2023 at 06:38:12PM -0400, Martin K. Petersen wrote:
> Hi Maximilian!

Hi Martin,

thanks for your response.

> 
> > This is similar to commit 7a2ae008a53c ("scsi: megaraid: Fix
> > mega_cmd_done() CMDID_INT_CMDS").
> 
> That's supposed to be commit 75cb113cd43f, right?

Sorry, yes I meant this commit. I accidentally got the commit id form the 5.4
backport.

> 
> > When cmdid == CMDID_INT_CMDS and status != 0 then mbox is still NULL
> > but is dereferenced below.
> 
> Is this actually a valid scenario, though? The mbox is only dereferenced
> if there is status returned from an attached device. And I am guessing
> that a controller-internal command does not talk to any attached device.
> Thus status should always be 0 for CMDID_INT_CMDS. I don't have the
> megaraid firmware manual so this is pure guesswork on my part. But you
> would think we would have come across an invalid deref since the
> original 2014 commit made the offending change.
> 

This could indeed be the case. I only found this because it was reported by
static code analysis. However, by reading the code it's not obvious that this is
how it works. Should we therefore skip the whole status checking switch for
internal commands to make it more clear? For example, by a goto to the end of
the loop when the scb gets freed or just adding the scb free, list removal
and a continue?




Amazon Development Center Germany GmbH
Krausenstr. 38
10117 Berlin
Geschaeftsfuehrung: Christian Schlaeger, Jonathan Weiss
Eingetragen am Amtsgericht Charlottenburg unter HRB 149173 B
Sitz: Berlin
Ust-ID: DE 289 237 879
diff mbox series

Patch

diff --git a/drivers/scsi/megaraid.c b/drivers/scsi/megaraid.c
index e92f1a73cc9b..4dfe8865a18a 100644
--- a/drivers/scsi/megaraid.c
+++ b/drivers/scsi/megaraid.c
@@ -1442,6 +1442,7 @@  mega_cmd_done(adapter_t *adapter, u8 completed[], int nstatus, int status)
 		if (cmdid == CMDID_INT_CMDS) {
 			scb = &adapter->int_scb;
 			cmd = scb->cmd;
+			mbox = (mbox_t *)scb->raw_mbox;
 
 			list_del_init(&scb->list);
 			scb->state = SCB_FREE;