new file mode 100644
@@ -0,0 +1 @@
+obj-y += setup.o
new file mode 100644
@@ -0,0 +1,317 @@
+/*
+ * linux/arch/sh/kernel/setup_sh2007.c
+ *
+ * Copyright (C) 2003,2004 SUGIOKA Toshinobu
+ * Ported to Linux 2.6.34 by Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/ide.h>
+#include <linux/mm.h>
+#include <linux/dma-mapping.h>
+#include <linux/vmalloc.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/smsc911x.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+
+#include <asm/io.h>
+#include <asm/machvec.h>
+#include <asm/rtc.h>
+#include <asm/cacheflush.h>
+#include <asm/addrspace.h>
+
+#include "../../drivers/pci/pci-sh7780.h"
+
+#define INTEVT 0xff000028
+#define CPUOPM 0xff2f0000
+#define IRMCR 0xff000078
+#define CS5BCR 0xff802050
+#define CS5WCR 0xff802058
+#define CS5PCR 0xff802070
+
+#define BUS_SZ8 1
+#define BUS_SZ16 2
+#define BUS_SZ32 3
+
+#define PCMCIA_IODYN 1
+#define PCMCIA_ATA 0
+#define PCMCIA_IO8 2
+#define PCMCIA_IO16 3
+#define PCMCIA_COMM8 4
+#define PCMCIA_COMM16 5
+#define PCMCIA_ATTR8 6
+#define PCMCIA_ATTR16 7
+
+#define TYPE_SRAM 0
+#define TYPE_PCMCIA 4
+
+/* write-read/write-write delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWW5 0
+#define IWW6 3
+/* different area, read-write delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRWD5 2
+#define IWRWD6 2
+/* same area, read-write delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRWS5 2
+#define IWRWS6 2
+/* different area, read-read delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRRD5 2
+#define IWRRD6 2
+/* same area, read-read delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRRS5 0
+#define IWRRS6 2
+/* burst count (0-3:4,8,16,32) */
+#define BST5 0
+#define BST6 0
+/* bus size */
+#define SZ5 BUS_SZ16
+#define SZ6 BUS_SZ16
+/* RD hold for SRAM (0-1:0,1) */
+#define RDSPL5 0
+#define RDSPL6 0
+/* Burst pitch (0-7:0,1,2,3,4,5,6,7) */
+#define BW5 0
+#define BW6 0
+/* Multiplex (0-1:0,1) */
+#define MPX5 0
+#define MPX6 0
+/* device type */
+#define TYPE5 TYPE_PCMCIA
+#define TYPE6 TYPE_PCMCIA
+/* address setup before assert CSn for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define ADS5 0
+#define ADS6 0
+/* address hold after negate CSn for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define ADH5 0
+#define ADH6 0
+/* CSn assert to RD assert delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define RDS5 0
+#define RDS6 0
+/* RD negate to CSn negate delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define RDH5 0
+#define RDH6 0
+/* CSn assert to WE assert delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define WTS5 0
+#define WTS6 0
+/* WE negate to CSn negate delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define WTH5 0
+#define WTH6 0
+/* BS hold (0-1:1,2) */
+#define BSH5 0
+#define BSH6 0
+/* wait cycle (0-15:0,1,2,3,4,5,6,7,8,9,11,13,15,17,21,25) */
+#define IW5 6 /* 60ns PIO mode 4 */
+#define IW6 15 /* 250ns */
+
+#define SAA5 PCMCIA_IODYN /* IDE area b4000000-b5ffffff */
+#define SAB5 PCMCIA_IODYN /* CF area b6000000-b7ffffff */
+#define PCWA5 0 /* additional wait A (0-3:0,15,30,50) */
+#define PCWB5 0 /* additional wait B (0-3:0,15,30,50) */
+/* wait B (0-15:0,1,2,3,4,5,6,7,8,9,11,13,15,17,21,25) */
+#define PCIW5 12
+/* Address->OE/WE assert delay A (0-7:0,1,2,3,6,9,12,15) */
+#define TEDA5 2
+/* Address->OE/WE assert delay B (0-7:0,1,2,3,6,9,12,15) */
+#define TEDB5 4
+/* OE/WE negate->Address delay A (0-7:0,1,2,3,6,9,12,15) */
+#define TEHA5 2
+/* OE/WE negate->Address delay B (0-7:0,1,2,3,6,9,12,15) */
+#define TEHB5 3
+
+#define CS5BCR_D ((IWW5<<28)|(IWRWD5<<24)|(IWRWS5<<20)| \
+ (IWRRD5<<16)|(IWRRS5<<12)|(BST5<<10)| \
+ (SZ5<<8)|(RDSPL5<<7)|(BW5<<4)|(MPX5<<3)|TYPE5)
+#define CS5WCR_D ((ADS5<<28)|(ADH5<<24)|(RDS5<<20)| \
+ (RDH5<<16)|(WTS5<<12)|(WTH5<<8)|(BSH5<<4)|IW5)
+#define CS5PCR_D ((SAA5<<28)|(SAB5<<24)|(PCWA5<<22)| \
+ (PCWB5<<20)|(PCIW5<<16)|(TEDA5<<12)| \
+ (TEDB5<<8)|(TEHA5<<4)|TEHB5)
+
+#define SMC0_BASE 0xb0800000 /* eth0 */
+#define SMC1_BASE 0xb0900000 /* eth1 */
+#define CF_BASE 0xb6100000 /* Compact Flash (I/O area) */
+#define IDE_BASE 0xb4000000 /* IDE */
+#define PC104_IO_BASE 0xb8000000
+#define PC104_MEM_BASE 0xba000000
+#define SMC_IO_SIZE 0x100
+
+#define CF_OFFSET 0x1f0
+#define IDE_OFFSET 0x170
+
+struct smsc911x_platform_config smc911x_info = {
+ .flags = SMSC911X_USE_32BIT,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
+};
+
+static struct resource smsc9118_0_resources[] = {
+ [0] = {
+ .start = SMC0_BASE,
+ .end = SMC0_BASE + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = evt2irq(0x240),
+ .end = evt2irq(0x240),
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct resource smsc9118_1_resources[] = {
+ [0] = {
+ .start = SMC1_BASE,
+ .end = SMC1_BASE + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = evt2irq(0x280),
+ .end = evt2irq(0x280),
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device smsc9118_0_device = {
+ .name = "smsc911x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smsc9118_0_resources),
+ .resource = smsc9118_0_resources,
+ .dev = {
+ .platform_data = &smc911x_info,
+ },
+};
+
+static struct platform_device smsc9118_1_device = {
+ .name = "smsc911x",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(smsc9118_1_resources),
+ .resource = smsc9118_1_resources,
+ .dev = {
+ .platform_data = &smc911x_info,
+ },
+};
+
+static struct resource cf_resources[] = {
+ [0] = {
+ .start = CF_BASE + CF_OFFSET,
+ .end = CF_BASE + CF_OFFSET + 0x0f,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CF_BASE + CF_OFFSET + 0x206,
+ .end = CF_BASE + CF_OFFSET + 0x20f,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = evt2irq(0x2c0),
+ .end = evt2irq(0x2c0),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct pata_platform_info cf_info = {
+};
+
+static struct platform_device cf_device = {
+ .name = "pata_platform",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(cf_resources),
+ .resource = cf_resources,
+ .dev = {
+ .platform_data = &cf_info,
+ },
+};
+
+/*
+ * FIXME:
+ * I cannot test IDE of SH-2007.
+ * If you have SH-2007 and can test IDE,
+ * please define IDE_TESTED as 1.
+ *
+ * And if your SH-2007 can treat IDE disk well,
+ * please email to mitake@dcl.info.waseda.ac.jp and linux-sh@vger.kernel.org
+ */
+
+#define IDE_TESTED 0
+#if IDE_TESTED
+static struct resource ide_resources[] = {
+ [0] = {
+ .start = IDE_BASE + IDE_OFFSET,
+ .end = IDE_BASE + IDE_OFFSET + 0x0f,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IDE_BASE + IDE_OFFSET + 0x206,
+ .end = IDE_BASE + IDE_OFFSET + 0x20f,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = evt2irq(0x300),
+ .end = evt2irq(0x300),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+
+static struct pata_platform_info ide_info = {
+};
+
+static struct platform_device ide_device = {
+ .name = "pata_platform",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(ide_resources),
+ .resource = ide_resources,
+ .dev = {
+ .platform_data = &ide_info,
+ },
+};
+#endif
+
+static struct platform_device *sh2007_devices[] __initdata = {
+ &smsc9118_0_device,
+ &smsc9118_1_device,
+ &cf_device,
+#if IDE_TESTED
+ &ide_device,
+#endif
+};
+
+static int __init sh2007_io_init(void)
+{
+ platform_add_devices(sh2007_devices, ARRAY_SIZE(sh2007_devices));
+ return 0;
+}
+subsys_initcall(sh2007_io_init);
+
+static void __init sh2007_init_irq(void)
+{
+ plat_irq_setup_pins(IRQ_MODE_IRQ);
+}
+
+/*
+ * Initialize the board
+ */
+static void __init sh2007_setup(char **cmdline_p)
+{
+ printk(KERN_INFO "SH-2007 Setup...");
+
+ /* setup wait control registers for area 5 */
+ __raw_writel(CS5BCR_D, CS5BCR);
+ __raw_writel(CS5WCR_D, CS5WCR);
+ __raw_writel(CS5PCR_D, CS5PCR);
+
+ printk(KERN_INFO " done.\n");
+}
+
+/*
+ * The Machine Vector
+ */
+struct sh_machine_vector mv_sh2007 __initmv = {
+ .mv_setup = sh2007_setup,
+ .mv_name = "sh2007",
+ .mv_init_irq = sh2007_init_irq,
+};
@@ -60,3 +60,4 @@ ESPT SH_ESPT
POLARIS SH_POLARIS
KFR2R09 SH_KFR2R09
ECOVEC SH_ECOVEC
+SH2007 SH_SH2007