@@ -155,12 +155,15 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
mode->hsync_start - 1);
rcar_du_crtc_write(rcrtc, HCR, mode->htotal - 1);
- rcar_du_crtc_write(rcrtc, VDSR, mode->vtotal - mode->vsync_end - 2);
- rcar_du_crtc_write(rcrtc, VDER, mode->vtotal - mode->vsync_end +
- mode->vdisplay - 2);
- rcar_du_crtc_write(rcrtc, VSPR, mode->vtotal - mode->vsync_end +
- mode->vsync_start - 1);
- rcar_du_crtc_write(rcrtc, VCR, mode->vtotal - 1);
+ rcar_du_crtc_write(rcrtc, VDSR, mode->crtc_vtotal -
+ mode->crtc_vsync_end - 2);
+ rcar_du_crtc_write(rcrtc, VDER, mode->crtc_vtotal -
+ mode->crtc_vsync_end +
+ mode->crtc_vdisplay - 2);
+ rcar_du_crtc_write(rcrtc, VSPR, mode->crtc_vtotal -
+ mode->crtc_vsync_end +
+ mode->crtc_vsync_start - 1);
+ rcar_du_crtc_write(rcrtc, VCR, mode->crtc_vtotal - 1);
rcar_du_crtc_write(rcrtc, DESR, mode->htotal - mode->hsync_start);
rcar_du_crtc_write(rcrtc, DEWR, mode->hdisplay);
@@ -256,6 +259,7 @@ void rcar_du_crtc_update_planes(struct drm_crtc *crtc)
static void rcar_du_crtc_start(struct rcar_du_crtc *rcrtc)
{
struct drm_crtc *crtc = &rcrtc->crtc;
+ bool interlaced;
unsigned int i;
if (rcrtc->started)
@@ -291,7 +295,10 @@ static void rcar_du_crtc_start(struct rcar_du_crtc *rcrtc)
* sync mode (with the HSYNC and VSYNC signals configured as outputs and
* actively driven).
*/
- rcar_du_crtc_clr_set(rcrtc, DSYSR, DSYSR_TVM_MASK, DSYSR_TVM_MASTER);
+ interlaced = rcrtc->crtc.mode.flags & DRM_MODE_FLAG_INTERLACE;
+ rcar_du_crtc_clr_set(rcrtc, DSYSR, DSYSR_TVM_MASK | DSYSR_SCM_MASK,
+ (interlaced ? DSYSR_SCM_INT_VIDEO : 0) |
+ DSYSR_TVM_MASTER);
rcar_du_group_start_stop(rcrtc->group, true);
@@ -528,7 +535,7 @@ static irqreturn_t rcar_du_crtc_irq(int irq, void *arg)
status = rcar_du_crtc_read(rcrtc, DSSR);
rcar_du_crtc_write(rcrtc, DSRCR, status & DSRCR_MASK);
- if (status & DSSR_VBK) {
+ if (status & DSSR_FRM) {
drm_handle_vblank(rcrtc->crtc.dev, rcrtc->index);
rcar_du_crtc_finish_page_flip(rcrtc);
ret = IRQ_HANDLED;
@@ -95,6 +95,7 @@ int rcar_du_hdmi_connector_init(struct rcar_du_device *rcdu,
connector = &rcon->connector;
connector->display_info.width_mm = 0;
connector->display_info.height_mm = 0;
+ connector->interlace_allowed = true;
connector->polled = DRM_CONNECTOR_POLL_HPD;
ret = drm_connector_init(rcdu->ddev, connector, &connector_funcs,
@@ -104,14 +104,22 @@ void rcar_du_plane_update_base(struct rcar_du_plane *plane)
{
struct rcar_du_group *rgrp = plane->group;
unsigned int index = plane->hwindex;
+ bool interlaced;
u32 mwr;
- /* Memory pitch (expressed in pixels) */
+ interlaced = plane->crtc->mode.flags & DRM_MODE_FLAG_INTERLACE;
+
+ /* Memory pitch (expressed in pixels). Must be doubled for interlaced
+ * operation with 32bpp formats.
+ */
if (plane->format->planes == 2)
mwr = plane->pitch;
else
mwr = plane->pitch * 8 / plane->format->bpp;
+ if (interlaced && plane->format->bpp == 32)
+ mwr *= 2;
+
rcar_du_plane_write(rgrp, index, PnMWR, mwr);
/* The Y position is expressed in raster line units and must be doubled
@@ -119,12 +127,16 @@ void rcar_du_plane_update_base(struct rcar_du_plane *plane)
* doubling the Y position is found in the R8A7779 datasheet, but the
* rule seems to apply there as well.
*
+ * Despite not being documented, doubling seem not to be needed when
+ * operating in interlaced mode.
+ *
* Similarly, for the second plane, NV12 and NV21 formats seem to
- * require a halved Y position value.
+ * require a halved Y position value, in both progressive and interlaced
+ * modes.
*/
rcar_du_plane_write(rgrp, index, PnSPXR, plane->src_x);
rcar_du_plane_write(rgrp, index, PnSPYR, plane->src_y *
- (plane->format->bpp == 32 ? 2 : 1));
+ (!interlaced && plane->format->bpp == 32 ? 2 : 1));
rcar_du_plane_write(rgrp, index, PnDSA0R, plane->dma[0]);
if (plane->format->planes == 2) {
@@ -34,6 +34,7 @@
#define DSYSR_SCM_INT_NONE (0 << 4)
#define DSYSR_SCM_INT_SYNC (2 << 4)
#define DSYSR_SCM_INT_VIDEO (3 << 4)
+#define DSYSR_SCM_MASK (3 << 4)
#define DSMR 0x00004
#define DSMR_VSPM (1 << 28)
@@ -64,6 +64,7 @@ int rcar_du_vga_connector_init(struct rcar_du_device *rcdu,
connector = &rcon->connector;
connector->display_info.width_mm = 0;
connector->display_info.height_mm = 0;
+ connector->interlace_allowed = true;
ret = drm_connector_init(rcdu->ddev, connector, &connector_funcs,
DRM_MODE_CONNECTOR_VGA);
Accept interlaced modes on the VGA and HDMI connectors and configure the hardware accordingly. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> --- drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 23 +++++++++++++++-------- drivers/gpu/drm/rcar-du/rcar_du_hdmicon.c | 1 + drivers/gpu/drm/rcar-du/rcar_du_plane.c | 18 +++++++++++++++--- drivers/gpu/drm/rcar-du/rcar_du_regs.h | 1 + drivers/gpu/drm/rcar-du/rcar_du_vgacon.c | 1 + 5 files changed, 33 insertions(+), 11 deletions(-)