| Message ID | 20221027045157.23325-5-hayashi.kunihiko@socionext.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add UniPhier boards support | expand |
On Thu, Oct 27, 2022, at 06:51, Kunihiko Hayashi wrote: > Initial version of devicetree sources for NX1 SoC and boards. > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Can you add more information here? When new SoCs get added, I usually provide more than this in my own pull requests sending the patches to Linus, so please add some background here, such as: - is this a new SoC, or or something that has been around for a while and only now gets upstreamed? - What is the target market for this SoC? Are there any products one can buy with it? - What type of CPU cores does it use, or any other noteworthy IP blocks that are relevant for its purpose? > + usb_hsphy0: hs-phy@200 { > + compatible = "socionext,uniphier-nx1-usb3-hsphy"; > + reg = <0x200 0x10>; > + usb_ssphy0: ss-phy@300 { > + compatible = "socionext,uniphier-nx1-usb3-ssphy"; > + reg = <0x300 0x10>; I think these are usually just named 'phy@' instead of 'hs-phy@' > + ranges = > + /* downstream I/O */ > + <0x81000000 0 0x00000000 0x0ffe0000 0 0x00010000>, > + /* non-prefetchable memory */ > + <0x82000000 0 0x20000000 0x04200000 0 0x0bde0000>; 200MB of memory space is rather small, is there no 64-bit range? > + #interrupt-cells = <1>; > + interrupt-names = "dma", "msi"; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ > + <0 0 0 2 &pcie_intc 1>, /* INTB */ > + <0 0 0 3 &pcie_intc 2>, /* INTC */ > + <0 0 0 4 &pcie_intc 3>; /* INTD */ > + phy-names = "pcie-phy"; > + phys = <&pcie_phy>; > + > + pcie_intc: legacy-interrupt-controller { > + interrupt-controller; > + #interrupt-cells = <1>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > + }; > + }; Shouldn't there be an "msi-map" or "msi-parent" property pointing at the GIC? Arnd
Hi Arnd, Thank you for your comment. On 2022/10/27 19:01, Arnd Bergmann wrote: > On Thu, Oct 27, 2022, at 06:51, Kunihiko Hayashi wrote: >> Initial version of devicetree sources for NX1 SoC and boards. >> >> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > > Can you add more information here? When new SoCs get added, I > usually provide more than this in my own pull requests sending > the patches to Linus, so please add some background here, such as: > > - is this a new SoC, or or something that has been around for a while > and only now gets upstreamed? > > - What is the target market for this SoC? Are there any products > one can buy with it? > > - What type of CPU cores does it use, or any other noteworthy > IP blocks that are relevant for its purpose? This advice is good for me. I'll add some background for this SoC to the commit. >> + usb_hsphy0: hs-phy@200 { >> + compatible = > "socionext,uniphier-nx1-usb3-hsphy"; >> + reg = <0x200 0x10>; > >> + usb_ssphy0: ss-phy@300 { >> + compatible = > "socionext,uniphier-nx1-usb3-ssphy"; >> + reg = <0x300 0x10>; > > I think these are usually just named 'phy@' instead of 'hs-phy@' I see. Since it was adapted to other SoCs, I'll rename the node as well in another patch. >> + ranges = >> + /* downstream I/O */ >> + <0x81000000 0 0x00000000 0x0ffe0000 0 > 0x00010000>, >> + /* non-prefetchable memory */ >> + <0x82000000 0 0x20000000 0x04200000 0 > 0x0bde0000>; > > 200MB of memory space is rather small, is there no 64-bit range? Unfortunately, this SoC has only 190MB of PCIe memory space. >> + #interrupt-cells = <1>; >> + interrupt-names = "dma", "msi"; >> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-map-mask = <0 0 0 7>; >> + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ >> + <0 0 0 2 &pcie_intc 1>, /* INTB */ >> + <0 0 0 3 &pcie_intc 2>, /* INTC */ >> + <0 0 0 4 &pcie_intc 3>; /* INTD */ >> + phy-names = "pcie-phy"; >> + phys = <&pcie_phy>; >> + >> + pcie_intc: legacy-interrupt-controller { >> + interrupt-controller; >> + #interrupt-cells = <1>; >> + interrupt-parent = <&gic>; >> + interrupts = <GIC_SPI 86 > IRQ_TYPE_LEVEL_HIGH>; >> + }; >> + }; > > Shouldn't there be an "msi-map" or "msi-parent" property pointing at > the GIC? Since Designware PCIe receives an interrupt from GIC with interrupt-name "msi" and passes the interrupt to the linear irq domain corresponding to MSI, I think there is neither "msi-map" nor "msi-parent" properties. Thank you, --- Best Regards Kunihiko Hayashi
On Thu, Oct 27, 2022, at 13:19, Kunihiko Hayashi wrote: > On 2022/10/27 19:01, Arnd Bergmann wrote: >> On Thu, Oct 27, 2022, at 06:51, Kunihiko Hayashi wrote: >>> + #interrupt-cells = <1>; >>> + interrupt-names = "dma", "msi"; >>> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, >>> + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; >>> + interrupt-map-mask = <0 0 0 7>; >>> + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ >>> + <0 0 0 2 &pcie_intc 1>, /* INTB */ >>> + <0 0 0 3 &pcie_intc 2>, /* INTC */ >>> + <0 0 0 4 &pcie_intc 3>; /* INTD */ >>> + phy-names = "pcie-phy"; >>> + phys = <&pcie_phy>; >>> + >>> + pcie_intc: legacy-interrupt-controller { >>> + interrupt-controller; >>> + #interrupt-cells = <1>; >>> + interrupt-parent = <&gic>; >>> + interrupts = <GIC_SPI 86 >> IRQ_TYPE_LEVEL_HIGH>; >>> + }; >>> + }; >> >> Shouldn't there be an "msi-map" or "msi-parent" property pointing at >> the GIC? > > Since Designware PCIe receives an interrupt from GIC with interrupt-name "msi" > and passes the interrupt to the linear irq domain corresponding to MSI, > I think there is neither "msi-map" nor "msi-parent" properties. Usually, you have the choice to use either the built-in MSI logic of the PCIe controller, or the one built into the GIC itself, assuming you have a modern enough GIC implemetation. Using the GIC is preferred here, because otherwise you lose all the benefits that MSIs offer, regarding latency and CPU affinity. Arnd
On 2022/10/27 20:28, Arnd Bergmann wrote: > On Thu, Oct 27, 2022, at 13:19, Kunihiko Hayashi wrote: >> On 2022/10/27 19:01, Arnd Bergmann wrote: >>> On Thu, Oct 27, 2022, at 06:51, Kunihiko Hayashi wrote: > >>>> + #interrupt-cells = <1>; >>>> + interrupt-names = "dma", "msi"; >>>> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, >>>> + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; >>>> + interrupt-map-mask = <0 0 0 7>; >>>> + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ >>>> + <0 0 0 2 &pcie_intc 1>, /* INTB */ >>>> + <0 0 0 3 &pcie_intc 2>, /* INTC */ >>>> + <0 0 0 4 &pcie_intc 3>; /* INTD */ >>>> + phy-names = "pcie-phy"; >>>> + phys = <&pcie_phy>; >>>> + >>>> + pcie_intc: legacy-interrupt-controller { >>>> + interrupt-controller; >>>> + #interrupt-cells = <1>; >>>> + interrupt-parent = <&gic>; >>>> + interrupts = <GIC_SPI 86 >>> IRQ_TYPE_LEVEL_HIGH>; >>>> + }; >>>> + }; >>> >>> Shouldn't there be an "msi-map" or "msi-parent" property pointing at >>> the GIC? >> >> Since Designware PCIe receives an interrupt from GIC with interrupt-name > "msi" >> and passes the interrupt to the linear irq domain corresponding to MSI, >> I think there is neither "msi-map" nor "msi-parent" properties. > > Usually, you have the choice to use either the built-in > MSI logic of the PCIe controller, or the one built into the > GIC itself, assuming you have a modern enough GIC implemetation. I recognize ITS built into GICv3 can perform the parent of MSI. > Using the GIC is preferred here, because otherwise you lose > all the benefits that MSIs offer, regarding latency and CPU > affinity. I understand, however, unfortunately GIC-ITS (or something alternative) isn't supported in this SoC, so I think it is difficult to use the GIC itself as msi-parent. Thank you, --- Best Regards Kunihiko Hayashi
On Thu, Oct 27, 2022, at 13:58, Kunihiko Hayashi wrote: > On 2022/10/27 20:28, Arnd Bergmann wrote: >> Using the GIC is preferred here, because otherwise you lose >> all the benefits that MSIs offer, regarding latency and CPU >> affinity. > > I understand, however, unfortunately GIC-ITS (or something alternative) > isn't supported in this SoC, so I think it is difficult to use the GIC > itself as msi-parent. Ok, got it. arnd
On 27/10/2022 00:51, Kunihiko Hayashi wrote: > Initial version of devicetree sources for NX1 SoC and boards. > Thank you for your patch. There is something to discuss/improve. > diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi > new file mode 100644 > index 000000000000..e401763de86e > --- /dev/null > +++ b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi > @@ -0,0 +1,704 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +// > +// Device Tree Source for UniPhier NX1 SoC > +// > +// Copyright (C) 2021 Socionext Inc. > +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/gpio/uniphier-gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/thermal/thermal.h> > + > +/ { > + compatible = "socionext,uniphier-nx1"; > + #address-cells = <2>; > + #size-cells = <2>; > + interrupt-parent = <&gic>; > + > + cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + cpu-map { > + cluster0 { > + core0 { > + cpu = <&cpu0>; > + }; > + core1 { > + cpu = <&cpu1>; > + }; > + core2 { > + cpu = <&cpu2>; > + }; > + core3 { > + cpu = <&cpu3>; > + }; > + }; > + }; > + > + cpu0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0 0x000>; > + clocks = <&sys_clk 33>; > + enable-method = "psci"; > + next-level-cache = <&l2>; > + operating-points-v2 = <&cluster0_opp>; > + #cooling-cells = <2>; > + }; > + > + cpu1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0 0x001>; > + clocks = <&sys_clk 33>; > + enable-method = "psci"; > + next-level-cache = <&l2>; > + operating-points-v2 = <&cluster0_opp>; > + #cooling-cells = <2>; > + }; > + > + cpu2: cpu@2 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0 0x002>; > + clocks = <&sys_clk 33>; > + enable-method = "psci"; > + next-level-cache = <&l2>; > + operating-points-v2 = <&cluster0_opp>; > + #cooling-cells = <2>; > + }; > + > + cpu3: cpu@3 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0 0x003>; > + clocks = <&sys_clk 33>; > + enable-method = "psci"; > + next-level-cache = <&l2>; > + operating-points-v2 = <&cluster0_opp>; > + #cooling-cells = <2>; > + }; > + > + l2: l2-cache { > + compatible = "cache"; > + }; > + }; > + > + cluster0_opp: opp-table { > + compatible = "operating-points-v2"; > + opp-shared; > + > + opp-78125000 { > + opp-hz = /bits/ 64 <78125000>; > + clock-latency-ns = <300>; > + }; > + opp-156250000 { > + opp-hz = /bits/ 64 <156250000>; > + clock-latency-ns = <300>; > + }; > + opp-312500000 { > + opp-hz = /bits/ 64 <312500000>; > + clock-latency-ns = <300>; > + }; > + opp-625000000 { > + opp-hz = /bits/ 64 <625000000>; > + clock-latency-ns = <300>; > + }; > + opp-1250000000 { > + opp-hz = /bits/ 64 <1250000000>; > + clock-latency-ns = <300>; > + }; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + clocks { > + refclk: ref { Generic node name, so at least "clock" prefix or suffix. > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <25000000>; Are you sure the clock is a property of a SoC? IOW, it is physically on the SoC? If not, define entire clock or its frequency by boards. > + }; > + }; > + > + emmc_pwrseq: emmc-pwrseq { > + compatible = "mmc-pwrseq-emmc"; > + reset-gpios = <&gpio UNIPHIER_GPIO_PORT(3, 0) GPIO_ACTIVE_LOW>; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + thermal-zones { > + cpu-thermal { > + polling-delay-passive = <250>; /* 250ms */ > + polling-delay = <1000>; /* 1000ms */ > + thermal-sensors = <&pvtctl>; > + > + trips { > + cpu_crit: cpu-crit { > + temperature = <120000>; /* 120C */ > + hysteresis = <2000>; > + type = "critical"; > + }; > + cpu_alert: cpu-alert { > + temperature = <110000>; /* 110C */ > + hysteresis = <2000>; > + type = "passive"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&cpu_alert>; > + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + secure-memory@21000000 { > + reg = <0x0 0x21000000 0x0 0x01000000>; > + no-map; > + }; > + }; > + > + soc@0 { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0 0 0xffffffff>; > + > + sysctrl: sysctrl@11840000 { Node name: system-controller or syscon > + compatible = "socionext,uniphier-nx1-sysctrl", This looks undocumented. Did you run `make dtbs_check`? > + "simple-mfd", "syscon"; > + reg = <0x11840000 0x10000>; > + > + sys_clk: clock { Node name: clock-controller > + compatible = "socionext,uniphier-nx1-clock"; > + #clock-cells = <1>; > + }; > + > + sys_rst: reset { reset-controller > + compatible = "socionext,uniphier-nx1-reset"; > + #reset-cells = <1>; > + }; > + > + watchdog { > + compatible = "socionext,uniphier-wdt"; > + }; > + > + pvtctl: thermal-sensor { > + compatible = "socionext,uniphier-nx1-thermal"; > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; > + #thermal-sensor-cells = <0>; > + socionext,tmod-calibration = <0x0f22 0x68ee>; > + }; > + }; > + > + spi0: spi@14006000 { > + compatible = "socionext,uniphier-scssi"; > + status = "disabled"; > + reg = <0x14006000 0x100>; Reg is second property. Status goes last. The same in other nodes. > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi0>; > + clocks = <&peri_clk 11>; > + resets = <&peri_rst 11>; > + }; > + > + spi1: spi@14006100 { > + compatible = "socionext,uniphier-scssi"; > + status = "disabled"; > + reg = <0x14006100 0x100>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi1>; > + clocks = <&peri_clk 12>; > + resets = <&peri_rst 12>; > + }; > + > + serial0: serial@14006800 { > + compatible = "socionext,uniphier-uart"; > + status = "disabled"; > + reg = <0x14006800 0x40>; > + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart0>; > + clocks = <&peri_clk 0>; > + resets = <&peri_rst 0>; > + }; > + > + serial1: serial@14006900 { > + compatible = "socionext,uniphier-uart"; > + status = "disabled"; > + reg = <0x14006900 0x40>; > + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + clocks = <&peri_clk 1>; > + resets = <&peri_rst 1>; > + }; > + > + serial2: serial@14006a00 { > + compatible = "socionext,uniphier-uart"; > + status = "disabled"; > + reg = <0x14006a00 0x40>; > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + clocks = <&peri_clk 2>; > + resets = <&peri_rst 2>; > + }; > + > + serial3: serial@14006b00 { > + compatible = "socionext,uniphier-uart"; > + status = "disabled"; > + reg = <0x14006b00 0x40>; > + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + clocks = <&peri_clk 3>; > + resets = <&peri_rst 3>; > + }; > + > + gpio: gpio@14007000 { > + compatible = "socionext,uniphier-gpio"; > + reg = <0x14007000 0x200>; > + interrupt-parent = <&aidet>; > + interrupt-controller; > + #interrupt-cells = <2>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pinctrl 0 0 0>, > + <&pinctrl 49 0 0>, > + <&pinctrl 53 0 0>, > + <&pinctrl 96 0 0>, > + <&pinctrl 120 0 0>; > + gpio-ranges-group-names = "gpio_range0", > + "gpio_range1", > + "gpio_range2", > + "gpio_range3", > + "gpio_range4"; > + ngpios = <126>; > + socionext,interrupt-ranges = <0 48 6>; > + }; > + > + eth: ethernet@15000000 { > + compatible = "socionext,uniphier-nx1-ave4"; > + status = "disabled"; > + reg = <0x15000000 0x8500>; > + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ether_rgmii>; > + clock-names = "ether"; > + clocks = <&sys_clk 6>; > + reset-names = "ether"; > + resets = <&sys_rst 6>; > + phy-mode = "rgmii-id"; > + local-mac-address = [00 00 00 00 00 00]; > + socionext,syscon-phy-mode = <&soc_glue 0>; > + > + mdio: mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > + usb: usb@15a00000 { > + compatible = "socionext,uniphier-dwc3", "snps,dwc3"; > + status = "disabled"; > + reg = <0x15a00000 0xcd00>; > + interrupt-names = "host"; > + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>; > + clock-names = "ref", "bus_early", "suspend"; > + clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>; > + resets = <&usb_rst 15>; > + phys = <&usb_hsphy0>, <&usb_hsphy1>, > + <&usb_ssphy0>, <&usb_ssphy1>; > + dr_mode = "host"; > + }; > + > + usb-controller@15b00000 { > + compatible = "socionext,uniphier-nx1-dwc3-glue", Undocumented compatible. > + "simple-mfd"; Missing reg. Did you run `make dtbs_check`? Did you actually check it with dtc? > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0x15b00000 0x400>; > + > + usb_rst: reset@0 { reset-controller > + compatible = "socionext,uniphier-nx1-usb3-reset"; > + reg = <0x0 0x4>; > + #reset-cells = <1>; > + clock-names = "link"; > + clocks = <&sys_clk 12>; > + reset-names = "link"; > + resets = <&sys_rst 12>; > + }; > + > + usb_vbus0: regulator@100 { > + compatible = "socionext,uniphier-nx1-usb3-regulator"; > + reg = <0x100 0x10>; > + clock-names = "link"; > + clocks = <&sys_clk 12>; > + reset-names = "link"; > + resets = <&sys_rst 12>; > + }; > + > + usb_vbus1: regulator@110 { > + compatible = "socionext,uniphier-nx1-usb3-regulator"; > + reg = <0x110 0x10>; > + clock-names = "link"; > + clocks = <&sys_clk 12>; > + reset-names = "link"; > + resets = <&sys_rst 12>; > + }; > + > + usb_hsphy0: hs-phy@200 { Node name: phy The same in all other places. It can be also usb-phy and few others mentioned iin DT spec: https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > + compatible = "socionext,uniphier-nx1-usb3-hsphy"; > + reg = <0x200 0x10>; > + #phy-cells = <0>; > + clock-names = "link", "phy", "phy-ext"; > + clocks = <&sys_clk 12>, <&sys_clk 16>, > + <&sys_clk 13>; > + reset-names = "link", "phy"; > + resets = <&sys_rst 12>, <&sys_rst 16>; > + vbus-supply = <&usb_vbus0>; > + }; > + > + usb_hsphy1: hs-phy@210 { > + compatible = "socionext,uniphier-nx1-usb3-hsphy"; > + reg = <0x210 0x10>; > + #phy-cells = <0>; > + clock-names = "link", "phy", "phy-ext"; > + clocks = <&sys_clk 12>, <&sys_clk 16>, > + <&sys_clk 13>; > + reset-names = "link", "phy"; > + resets = <&sys_rst 12>, <&sys_rst 16>; > + vbus-supply = <&usb_vbus1>; > + }; > + > + usb_ssphy0: ss-phy@300 { > + compatible = "socionext,uniphier-nx1-usb3-ssphy"; > + reg = <0x300 0x10>; > + #phy-cells = <0>; > + clock-names = "link", "phy", "phy-ext"; > + clocks = <&sys_clk 12>, <&sys_clk 17>, > + <&sys_clk 13>; > + reset-names = "link", "phy"; > + resets = <&sys_rst 12>, <&sys_rst 17>; > + vbus-supply = <&usb_vbus0>; > + }; > + > + usb_ssphy1: ss-phy@310 { > + compatible = "socionext,uniphier-nx1-usb3-ssphy"; > + reg = <0x310 0x10>; > + #phy-cells = <0>; > + clock-names = "link", "phy", "phy-ext"; > + clocks = <&sys_clk 12>, <&sys_clk 18>, > + <&sys_clk 13>; > + reset-names = "link", "phy"; > + resets = <&sys_rst 12>, <&sys_rst 18>; > + vbus-supply = <&usb_vbus1>; > + }; > + }; > + > + pcie: pcie@16000000 { > + compatible = "socionext,uniphier-pcie"; > + status = "disabled"; > + reg-names = "dbi", "link", "config", "atu"; > + reg = <0x16000000 0x1000>, <0x179a0000 0x10000>, > + <0x0fff0000 0x10000>, <0x16300000 0x1000>; > + #address-cells = <3>; > + #size-cells = <2>; > + clocks = <&sys_clk 24>; > + resets = <&sys_rst 24>; > + num-lanes = <2>; > + num-viewport = <1>; > + bus-range = <0x0 0xff>; > + device_type = "pci"; > + ranges = > + /* downstream I/O */ > + <0x81000000 0 0x00000000 0x0ffe0000 0 0x00010000>, > + /* non-prefetchable memory */ > + <0x82000000 0 0x20000000 0x04200000 0 0x0bde0000>; > + #interrupt-cells = <1>; > + interrupt-names = "dma", "msi"; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ > + <0 0 0 2 &pcie_intc 1>, /* INTB */ > + <0 0 0 3 &pcie_intc 2>, /* INTC */ > + <0 0 0 4 &pcie_intc 3>; /* INTD */ > + phy-names = "pcie-phy"; > + phys = <&pcie_phy>; > + > + pcie_intc: legacy-interrupt-controller { > + interrupt-controller; > + #interrupt-cells = <1>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > + }; > + }; > + > + pcie_ep: pcie-ep@16000000 { > + compatible = "socionext,uniphier-nx1-pcie-ep"; > + status = "disabled"; > + reg-names = "dbi", "dbi2", "link", "addr_space", "atu"; > + reg = <0x16000000 0x1000>, <0x16100000 0x1000>, > + <0x179a0000 0x10000>, <0x04200000 0xbe00000>, > + <0x16300000 0x1000>; > + clock-names = "link"; > + clocks = <&sys_clk 24>; > + reset-names = "link"; > + resets = <&sys_rst 24>; > + num-ib-windows = <16>; > + num-ob-windows = <16>; > + num-lanes = <2>; > + phy-names = "pcie-phy"; > + phys = <&pcie_phy>; > + }; > + > + pcie_phy: phy@179b8000 { > + compatible = "socionext,uniphier-nx1-pcie-phy"; > + reg = <0x179b8000 0x4000>; > + #phy-cells = <0>; > + clock-names = "link"; > + clocks = <&sys_clk 24>; > + reset-names = "link"; > + resets = <&sys_rst 24>; > + socionext,syscon = <&sysctrl>; > + }; > + > + i2c0: i2c@18780000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18780000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c0>; > + clocks = <&peri_clk 4>; > + resets = <&peri_rst 4>; > + clock-frequency = <400000>; > + }; > + > + i2c1: i2c@18781000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18781000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + clocks = <&peri_clk 5>; > + resets = <&peri_rst 5>; > + clock-frequency = <400000>; > + }; > + > + i2c2: i2c@18782000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18782000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + clocks = <&peri_clk 6>; > + resets = <&peri_rst 6>; > + clock-frequency = <400000>; > + }; > + > + i2c3: i2c@18783000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18783000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + clocks = <&peri_clk 7>; > + resets = <&peri_rst 7>; > + clock-frequency = <400000>; > + }; > + > + i2c4: i2c@18784000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18784000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c4>; > + clocks = <&peri_clk 8>; > + resets = <&peri_rst 8>; > + clock-frequency = <100000>; > + }; > + > + i2c5: i2c@18785000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18785000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c5>; > + clocks = <&peri_clk 9>; > + resets = <&peri_rst 9>; > + clock-frequency = <100000>; > + }; > + > + i2c6: i2c@18786000 { > + compatible = "socionext,uniphier-fi2c"; > + status = "disabled"; > + reg = <0x18786000 0x80>; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c6>; > + clocks = <&peri_clk 10>; > + resets = <&peri_rst 10>; > + clock-frequency = <100000>; > + }; > + > + sdctrl@19810000 { Same comment as before... > + compatible = "socionext,uniphier-nx1-sdctrl", Same problem as before... > + "simple-mfd", "syscon"; > + reg = <0x19810000 0x400>; > + > + sd_clk: clock { > + compatible = "socionext,uniphier-nx1-sd-clock"; > + #clock-cells = <1>; > + }; > + > + sd_rst: reset { > + compatible = "socionext,uniphier-nx1-sd-reset"; > + #reset-cells = <1>; > + }; > + }; > + > + perictrl@19820000 { > + compatible = "socionext,uniphier-nx1-perictrl", Also undocumented. > + "simple-mfd", "syscon"; > + reg = <0x19820000 0x200>; > + > + peri_clk: clock { clock-controller > + compatible = "socionext,uniphier-nx1-peri-clock"; > + #clock-cells = <1>; > + }; > + > + peri_rst: reset { reset-controller > + compatible = "socionext,uniphier-nx1-peri-reset"; > + #reset-cells = <1>; > + }; > + }; > + > + emmc: mmc@1a000000 { > + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; > + reg = <0x1a000000 0x400>; > + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_emmc>; > + clocks = <&sys_clk 4>; > + resets = <&sys_rst 4>; > + bus-width = <8>; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + mmc-pwrseq = <&emmc_pwrseq>; > + cdns,phy-input-delay-legacy = <9>; > + cdns,phy-input-delay-mmc-highspeed = <2>; > + cdns,phy-input-delay-mmc-ddr = <3>; > + cdns,phy-dll-delay-sdclk = <21>; > + cdns,phy-dll-delay-sdclk-hsmmc = <21>; > + }; > + > + sd: mmc@1a400000 { > + compatible = "socionext,uniphier-sd-v3.1.1"; > + status = "disabled"; > + reg = <0x1a400000 0x800>; > + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sd>; > + clocks = <&sd_clk 0>; > + reset-names = "host"; > + resets = <&sd_rst 0>; > + bus-width = <4>; > + cap-sd-highspeed; > + }; > + > + soc_glue: soc-glue@1f800000 { > + compatible = "socionext,uniphier-nx1-soc-glue", I am not going to check... > + "simple-mfd", "syscon"; > + reg = <0x1f800000 0x2000>; > + > + pinctrl: pinctrl { > + compatible = "socionext,uniphier-nx1-pinctrl"; > + }; > + }; > + > + soc-glue@1f900000 { > + compatible = "socionext,uniphier-nx1-soc-glue-debug", Hm... > + "simple-mfd"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0x1f900000 0x2000>; > + }; > + > + xdmac: dma-controller@1fa10000 { > + compatible = "socionext,uniphier-xdmac"; > + reg = <0x1fa10000 0x5300>; > + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; > + dma-channels = <16>; > + #dma-cells = <2>; > + }; > + > + aidet: aidet@1fb20000 { Node names should be generic. https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > + compatible = "socionext,uniphier-nx1-aidet"; > + reg = <0x1fb20000 0x200>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; Best regards, Krzysztof
Hi Krzysztof, Sorry for late and thank you for reviewing. On 2022/10/27 22:36, Krzysztof Kozlowski wrote: > On 27/10/2022 00:51, Kunihiko Hayashi wrote: >> Initial version of devicetree sources for NX1 SoC and boards. >> > > Thank you for your patch. There is something to discuss/improve. > >> diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi >> b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi >> new file mode 100644 >> index 000000000000..e401763de86e >> --- /dev/null >> +++ b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi (snip) >> + clocks { >> + refclk: ref { > > Generic node name, so at least "clock" prefix or suffix. I see. I'll change the node name with "clock". >> + compatible = "fixed-clock"; >> + #clock-cells = <0>; >> + clock-frequency = <25000000>; > > Are you sure the clock is a property of a SoC? IOW, it is physically on > the SoC? If not, define entire clock or its frequency by boards. Indeed. This shows an external oscillator outside of a SoC. I'll consider to define the node or the property by board devicetree. >> + }; >> + }; >> + >> + emmc_pwrseq: emmc-pwrseq { >> + compatible = "mmc-pwrseq-emmc"; >> + reset-gpios = <&gpio UNIPHIER_GPIO_PORT(3, 0) GPIO_ACTIVE_LOW>; >> + }; >> + >> + timer { >> + compatible = "arm,armv8-timer"; >> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; >> + }; >> + >> + thermal-zones { >> + cpu-thermal { >> + polling-delay-passive = <250>; /* 250ms */ >> + polling-delay = <1000>; /* 1000ms */ >> + thermal-sensors = <&pvtctl>; >> + >> + trips { >> + cpu_crit: cpu-crit { >> + temperature = <120000>; /* 120C */ >> + hysteresis = <2000>; >> + type = "critical"; >> + }; >> + cpu_alert: cpu-alert { >> + temperature = <110000>; /* 110C */ >> + hysteresis = <2000>; >> + type = "passive"; >> + }; >> + }; >> + >> + cooling-maps { >> + map0 { >> + trip = <&cpu_alert>; >> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, >> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, >> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, >> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; >> + }; >> + }; >> + }; >> + }; >> + >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + secure-memory@21000000 { >> + reg = <0x0 0x21000000 0x0 0x01000000>; >> + no-map; >> + }; >> + }; >> + >> + soc@0 { >> + compatible = "simple-bus"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0 0 0xffffffff>; >> + >> + sysctrl: sysctrl@11840000 { > > Node name: system-controller or syscon I see. I'll rename it to a generic name. And also other system controller nodes in the same way. > >> + compatible = "socionext,uniphier-nx1-sysctrl", > > This looks undocumented. > > Did you run `make dtbs_check`? I've done it, however, I missed the dt-binding document for the system controller. I'll need to add a system controller's document before this patch. >> + "simple-mfd", "syscon"; >> + reg = <0x11840000 0x10000>; >> + >> + sys_clk: clock { > > Node name: clock-controller Need to rename to a generic name in the same way. After this as well. >> + compatible = "socionext,uniphier-nx1-clock"; >> + #clock-cells = <1>; >> + }; >> + >> + sys_rst: reset { > > reset-controller > >> + compatible = "socionext,uniphier-nx1-reset"; >> + #reset-cells = <1>; >> + }; >> + >> + watchdog { >> + compatible = "socionext,uniphier-wdt"; >> + }; >> + >> + pvtctl: thermal-sensor { >> + compatible = "socionext,uniphier-nx1-thermal"; >> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; >> + #thermal-sensor-cells = <0>; >> + socionext,tmod-calibration = <0x0f22 0x68ee>; >> + }; >> + }; >> + >> + spi0: spi@14006000 { >> + compatible = "socionext,uniphier-scssi"; >> + status = "disabled"; >> + reg = <0x14006000 0x100>; > > Reg is second property. Status goes last. The same in other nodes. Hmm, I've put "status" here according to the existing (uniphier's) DT policy and this should rewrite the policy. Is there documentation somewhere that recommends the order? Or, should I refer to previous comments? >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_spi0>; >> + clocks = <&peri_clk 11>; >> + resets = <&peri_rst 11>; >> + }; >> + >> + spi1: spi@14006100 { >> + compatible = "socionext,uniphier-scssi"; >> + status = "disabled"; >> + reg = <0x14006100 0x100>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_spi1>; >> + clocks = <&peri_clk 12>; >> + resets = <&peri_rst 12>; >> + }; >> + >> + serial0: serial@14006800 { >> + compatible = "socionext,uniphier-uart"; >> + status = "disabled"; >> + reg = <0x14006800 0x40>; >> + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_uart0>; >> + clocks = <&peri_clk 0>; >> + resets = <&peri_rst 0>; >> + }; >> + >> + serial1: serial@14006900 { >> + compatible = "socionext,uniphier-uart"; >> + status = "disabled"; >> + reg = <0x14006900 0x40>; >> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_uart1>; >> + clocks = <&peri_clk 1>; >> + resets = <&peri_rst 1>; >> + }; >> + >> + serial2: serial@14006a00 { >> + compatible = "socionext,uniphier-uart"; >> + status = "disabled"; >> + reg = <0x14006a00 0x40>; >> + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_uart2>; >> + clocks = <&peri_clk 2>; >> + resets = <&peri_rst 2>; >> + }; >> + >> + serial3: serial@14006b00 { >> + compatible = "socionext,uniphier-uart"; >> + status = "disabled"; >> + reg = <0x14006b00 0x40>; >> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_uart3>; >> + clocks = <&peri_clk 3>; >> + resets = <&peri_rst 3>; >> + }; >> + >> + gpio: gpio@14007000 { >> + compatible = "socionext,uniphier-gpio"; >> + reg = <0x14007000 0x200>; >> + interrupt-parent = <&aidet>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + gpio-ranges = <&pinctrl 0 0 0>, >> + <&pinctrl 49 0 0>, >> + <&pinctrl 53 0 0>, >> + <&pinctrl 96 0 0>, >> + <&pinctrl 120 0 0>; >> + gpio-ranges-group-names = "gpio_range0", >> + "gpio_range1", >> + "gpio_range2", >> + "gpio_range3", >> + "gpio_range4"; >> + ngpios = <126>; >> + socionext,interrupt-ranges = <0 48 6>; >> + }; >> + >> + eth: ethernet@15000000 { >> + compatible = "socionext,uniphier-nx1-ave4"; >> + status = "disabled"; >> + reg = <0x15000000 0x8500>; >> + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_ether_rgmii>; >> + clock-names = "ether"; >> + clocks = <&sys_clk 6>; >> + reset-names = "ether"; >> + resets = <&sys_rst 6>; >> + phy-mode = "rgmii-id"; >> + local-mac-address = [00 00 00 00 00 00]; >> + socionext,syscon-phy-mode = <&soc_glue 0>; >> + >> + mdio: mdio { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> + usb: usb@15a00000 { >> + compatible = "socionext,uniphier-dwc3", "snps,dwc3"; >> + status = "disabled"; >> + reg = <0x15a00000 0xcd00>; >> + interrupt-names = "host"; >> + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>; >> + clock-names = "ref", "bus_early", "suspend"; >> + clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>; >> + resets = <&usb_rst 15>; >> + phys = <&usb_hsphy0>, <&usb_hsphy1>, >> + <&usb_ssphy0>, <&usb_ssphy1>; >> + dr_mode = "host"; >> + }; >> + >> + usb-controller@15b00000 { >> + compatible = "socionext,uniphier-nx1-dwc3-glue", > > Undocumented compatible. > >> + "simple-mfd"; > > > Missing reg. Did you run `make dtbs_check`? Did you actually check it > with dtc? I missed it and will add it. >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0x15b00000 0x400>; >> + >> + usb_rst: reset@0 { > > reset-controller > >> + compatible = "socionext,uniphier-nx1-usb3-reset"; >> + reg = <0x0 0x4>; >> + #reset-cells = <1>; >> + clock-names = "link"; >> + clocks = <&sys_clk 12>; >> + reset-names = "link"; >> + resets = <&sys_rst 12>; >> + }; >> + >> + usb_vbus0: regulator@100 { >> + compatible = "socionext,uniphier-nx1-usb3-regulator"; >> + reg = <0x100 0x10>; >> + clock-names = "link"; >> + clocks = <&sys_clk 12>; >> + reset-names = "link"; >> + resets = <&sys_rst 12>; >> + }; >> + >> + usb_vbus1: regulator@110 { >> + compatible = "socionext,uniphier-nx1-usb3-regulator"; >> + reg = <0x110 0x10>; >> + clock-names = "link"; >> + clocks = <&sys_clk 12>; >> + reset-names = "link"; >> + resets = <&sys_rst 12>; >> + }; >> + >> + usb_hsphy0: hs-phy@200 { > > Node name: phy > > The same in all other places. It can be also usb-phy and few others > mentioned iin DT spec: > https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation I see. I'll replace the node name with "phy". >> + compatible = "socionext,uniphier-nx1-usb3-hsphy"; >> + reg = <0x200 0x10>; >> + #phy-cells = <0>; >> + clock-names = "link", "phy", "phy-ext"; >> + clocks = <&sys_clk 12>, <&sys_clk 16>, >> + <&sys_clk 13>; >> + reset-names = "link", "phy"; >> + resets = <&sys_rst 12>, <&sys_rst 16>; >> + vbus-supply = <&usb_vbus0>; >> + }; >> + >> + usb_hsphy1: hs-phy@210 { >> + compatible = "socionext,uniphier-nx1-usb3-hsphy"; >> + reg = <0x210 0x10>; >> + #phy-cells = <0>; >> + clock-names = "link", "phy", "phy-ext"; >> + clocks = <&sys_clk 12>, <&sys_clk 16>, >> + <&sys_clk 13>; >> + reset-names = "link", "phy"; >> + resets = <&sys_rst 12>, <&sys_rst 16>; >> + vbus-supply = <&usb_vbus1>; >> + }; >> + >> + usb_ssphy0: ss-phy@300 { >> + compatible = "socionext,uniphier-nx1-usb3-ssphy"; >> + reg = <0x300 0x10>; >> + #phy-cells = <0>; >> + clock-names = "link", "phy", "phy-ext"; >> + clocks = <&sys_clk 12>, <&sys_clk 17>, >> + <&sys_clk 13>; >> + reset-names = "link", "phy"; >> + resets = <&sys_rst 12>, <&sys_rst 17>; >> + vbus-supply = <&usb_vbus0>; >> + }; >> + >> + usb_ssphy1: ss-phy@310 { >> + compatible = "socionext,uniphier-nx1-usb3-ssphy"; >> + reg = <0x310 0x10>; >> + #phy-cells = <0>; >> + clock-names = "link", "phy", "phy-ext"; >> + clocks = <&sys_clk 12>, <&sys_clk 18>, >> + <&sys_clk 13>; >> + reset-names = "link", "phy"; >> + resets = <&sys_rst 12>, <&sys_rst 18>; >> + vbus-supply = <&usb_vbus1>; >> + }; >> + }; >> + >> + pcie: pcie@16000000 { >> + compatible = "socionext,uniphier-pcie"; >> + status = "disabled"; >> + reg-names = "dbi", "link", "config", "atu"; >> + reg = <0x16000000 0x1000>, <0x179a0000 0x10000>, >> + <0x0fff0000 0x10000>, <0x16300000 0x1000>; >> + #address-cells = <3>; >> + #size-cells = <2>; >> + clocks = <&sys_clk 24>; >> + resets = <&sys_rst 24>; >> + num-lanes = <2>; >> + num-viewport = <1>; >> + bus-range = <0x0 0xff>; >> + device_type = "pci"; >> + ranges = >> + /* downstream I/O */ >> + <0x81000000 0 0x00000000 0x0ffe0000 0 0x00010000>, >> + /* non-prefetchable memory */ >> + <0x82000000 0 0x20000000 0x04200000 0 0x0bde0000>; >> + #interrupt-cells = <1>; >> + interrupt-names = "dma", "msi"; >> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-map-mask = <0 0 0 7>; >> + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ >> + <0 0 0 2 &pcie_intc 1>, /* INTB */ >> + <0 0 0 3 &pcie_intc 2>, /* INTC */ >> + <0 0 0 4 &pcie_intc 3>; /* INTD */ >> + phy-names = "pcie-phy"; >> + phys = <&pcie_phy>; >> + >> + pcie_intc: legacy-interrupt-controller { >> + interrupt-controller; >> + #interrupt-cells = <1>; >> + interrupt-parent = <&gic>; >> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; >> + }; >> + }; >> + >> + pcie_ep: pcie-ep@16000000 { >> + compatible = "socionext,uniphier-nx1-pcie-ep"; >> + status = "disabled"; >> + reg-names = "dbi", "dbi2", "link", "addr_space", "atu"; >> + reg = <0x16000000 0x1000>, <0x16100000 0x1000>, >> + <0x179a0000 0x10000>, <0x04200000 0xbe00000>, >> + <0x16300000 0x1000>; >> + clock-names = "link"; >> + clocks = <&sys_clk 24>; >> + reset-names = "link"; >> + resets = <&sys_rst 24>; >> + num-ib-windows = <16>; >> + num-ob-windows = <16>; >> + num-lanes = <2>; >> + phy-names = "pcie-phy"; >> + phys = <&pcie_phy>; >> + }; >> + >> + pcie_phy: phy@179b8000 { >> + compatible = "socionext,uniphier-nx1-pcie-phy"; >> + reg = <0x179b8000 0x4000>; >> + #phy-cells = <0>; >> + clock-names = "link"; >> + clocks = <&sys_clk 24>; >> + reset-names = "link"; >> + resets = <&sys_rst 24>; >> + socionext,syscon = <&sysctrl>; >> + }; >> + >> + i2c0: i2c@18780000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18780000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c0>; >> + clocks = <&peri_clk 4>; >> + resets = <&peri_rst 4>; >> + clock-frequency = <400000>; >> + }; >> + >> + i2c1: i2c@18781000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18781000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c1>; >> + clocks = <&peri_clk 5>; >> + resets = <&peri_rst 5>; >> + clock-frequency = <400000>; >> + }; >> + >> + i2c2: i2c@18782000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18782000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c2>; >> + clocks = <&peri_clk 6>; >> + resets = <&peri_rst 6>; >> + clock-frequency = <400000>; >> + }; >> + >> + i2c3: i2c@18783000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18783000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c3>; >> + clocks = <&peri_clk 7>; >> + resets = <&peri_rst 7>; >> + clock-frequency = <400000>; >> + }; >> + >> + i2c4: i2c@18784000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18784000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c4>; >> + clocks = <&peri_clk 8>; >> + resets = <&peri_rst 8>; >> + clock-frequency = <100000>; >> + }; >> + >> + i2c5: i2c@18785000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18785000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c5>; >> + clocks = <&peri_clk 9>; >> + resets = <&peri_rst 9>; >> + clock-frequency = <100000>; >> + }; >> + >> + i2c6: i2c@18786000 { >> + compatible = "socionext,uniphier-fi2c"; >> + status = "disabled"; >> + reg = <0x18786000 0x80>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_i2c6>; >> + clocks = <&peri_clk 10>; >> + resets = <&peri_rst 10>; >> + clock-frequency = <100000>; >> + }; >> + >> + sdctrl@19810000 { > > Same comment as before... > >> + compatible = "socionext,uniphier-nx1-sdctrl", > > Same problem as before... > >> + "simple-mfd", "syscon"; >> + reg = <0x19810000 0x400>; >> + >> + sd_clk: clock { >> + compatible = "socionext,uniphier-nx1-sd-clock"; >> + #clock-cells = <1>; >> + }; >> + >> + sd_rst: reset { >> + compatible = "socionext,uniphier-nx1-sd-reset"; >> + #reset-cells = <1>; >> + }; >> + }; >> + >> + perictrl@19820000 { >> + compatible = "socionext,uniphier-nx1-perictrl", > > Also undocumented. > >> + "simple-mfd", "syscon"; >> + reg = <0x19820000 0x200>; >> + >> + peri_clk: clock { > > clock-controller > >> + compatible = "socionext,uniphier-nx1-peri-clock"; >> + #clock-cells = <1>; >> + }; >> + >> + peri_rst: reset { > > reset-controller > >> + compatible = "socionext,uniphier-nx1-peri-reset"; >> + #reset-cells = <1>; >> + }; >> + }; >> + >> + emmc: mmc@1a000000 { >> + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; >> + reg = <0x1a000000 0x400>; >> + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_emmc>; >> + clocks = <&sys_clk 4>; >> + resets = <&sys_rst 4>; >> + bus-width = <8>; >> + mmc-ddr-1_8v; >> + mmc-hs200-1_8v; >> + mmc-pwrseq = <&emmc_pwrseq>; >> + cdns,phy-input-delay-legacy = <9>; >> + cdns,phy-input-delay-mmc-highspeed = <2>; >> + cdns,phy-input-delay-mmc-ddr = <3>; >> + cdns,phy-dll-delay-sdclk = <21>; >> + cdns,phy-dll-delay-sdclk-hsmmc = <21>; >> + }; >> + >> + sd: mmc@1a400000 { >> + compatible = "socionext,uniphier-sd-v3.1.1"; >> + status = "disabled"; >> + reg = <0x1a400000 0x800>; >> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_sd>; >> + clocks = <&sd_clk 0>; >> + reset-names = "host"; >> + resets = <&sd_rst 0>; >> + bus-width = <4>; >> + cap-sd-highspeed; >> + }; >> + >> + soc_glue: soc-glue@1f800000 { >> + compatible = "socionext,uniphier-nx1-soc-glue", > > I am not going to check... > >> + "simple-mfd", "syscon"; >> + reg = <0x1f800000 0x2000>; >> + >> + pinctrl: pinctrl { >> + compatible = "socionext,uniphier-nx1-pinctrl"; >> + }; >> + }; >> + >> + soc-glue@1f900000 { >> + compatible = "socionext,uniphier-nx1-soc-glue-debug", > > Hm... > >> + "simple-mfd"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0x1f900000 0x2000>; >> + }; >> + >> + xdmac: dma-controller@1fa10000 { >> + compatible = "socionext,uniphier-xdmac"; >> + reg = <0x1fa10000 0x5300>; >> + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; >> + dma-channels = <16>; >> + #dma-cells = <2>; >> + }; >> + >> + aidet: aidet@1fb20000 { > > Node names should be generic. > https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation I forgot to rename it and will rename to "interrupt-controller". > >> + compatible = "socionext,uniphier-nx1-aidet"; >> + reg = <0x1fb20000 0x200>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + }; Thank you, --- Best Regards Kunihiko Hayashi
On 01/11/2022 05:02, Kunihiko Hayashi wrote: > Hi Krzysztof, > >>> + compatible = "socionext,uniphier-nx1-clock"; >>> + #clock-cells = <1>; >>> + }; >>> + >>> + sys_rst: reset { >> >> reset-controller >> >>> + compatible = "socionext,uniphier-nx1-reset"; >>> + #reset-cells = <1>; >>> + }; >>> + >>> + watchdog { >>> + compatible = "socionext,uniphier-wdt"; >>> + }; >>> + >>> + pvtctl: thermal-sensor { >>> + compatible = "socionext,uniphier-nx1-thermal"; >>> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; >>> + #thermal-sensor-cells = <0>; >>> + socionext,tmod-calibration = <0x0f22 0x68ee>; >>> + }; >>> + }; >>> + >>> + spi0: spi@14006000 { >>> + compatible = "socionext,uniphier-scssi"; >>> + status = "disabled"; >>> + reg = <0x14006000 0x100>; >> >> Reg is second property. Status goes last. The same in other nodes. > > Hmm, I've put "status" here according to the existing (uniphier's) DT policy > and this should rewrite the policy. Is there documentation somewhere that > recommends the order? Or, should I refer to previous comments? Hm, your decision (as arch maintainer) is then preferred, not mine. Although it is quite unusual to find status, not reg, as the second property. compatible followed by reg is not documented anywhere, it's just the most used style. And actually most sensible as it answers to questions from highest importance to lowest: 1. What is this device? compatible 2. Where is it? Does it match unit address? reg 3. all other properties 4. Is it off or on? status as optional property Best regards, Krzysztof
On 2022/11/03 1:48, Krzysztof Kozlowski wrote: > On 01/11/2022 05:02, Kunihiko Hayashi wrote: >> Hi Krzysztof, >> > > >>>> + compatible = "socionext,uniphier-nx1-clock"; >>>> + #clock-cells = <1>; >>>> + }; >>>> + >>>> + sys_rst: reset { >>> >>> reset-controller >>> >>>> + compatible = "socionext,uniphier-nx1-reset"; >>>> + #reset-cells = <1>; >>>> + }; >>>> + >>>> + watchdog { >>>> + compatible = "socionext,uniphier-wdt"; >>>> + }; >>>> + >>>> + pvtctl: thermal-sensor { >>>> + compatible = "socionext,uniphier-nx1-thermal"; >>>> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; >>>> + #thermal-sensor-cells = <0>; >>>> + socionext,tmod-calibration = <0x0f22 0x68ee>; >>>> + }; >>>> + }; >>>> + >>>> + spi0: spi@14006000 { >>>> + compatible = "socionext,uniphier-scssi"; >>>> + status = "disabled"; >>>> + reg = <0x14006000 0x100>; >>> >>> Reg is second property. Status goes last. The same in other nodes. >> >> Hmm, I've put "status" here according to the existing (uniphier's) DT >> policy >> and this should rewrite the policy. Is there documentation somewhere that >> recommends the order? Or, should I refer to previous comments? > > Hm, your decision (as arch maintainer) is then preferred, not mine. > Although it is quite unusual to find status, not reg, as the second > property. Okay, however, if there are no examples where the second is "status", I think it is better to follow the many descriptions for new additions. > compatible followed by reg is not documented anywhere, it's just the > most used style. And actually most sensible as it answers to questions > from highest importance to lowest: > 1. What is this device? compatible > 2. Where is it? Does it match unit address? reg > 3. all other properties > 4. Is it off or on? status as optional property I think it is reasonable to arrange the properties in order of importance. I'll put "reg" second in this addition in the next. Thank you, --- Best Regards Kunihiko Hayashi
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile index 33989a9643ac..0f198888484a 100644 --- a/arch/arm64/boot/dts/socionext/Makefile +++ b/arch/arm64/boot/dts/socionext/Makefile @@ -5,6 +5,9 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ld20-akebi96.dtb \ uniphier-ld20-global.dtb \ uniphier-ld20-ref.dtb \ + uniphier-nx1-evb.dtb \ + uniphier-nx1-ref.dtb \ + uniphier-nx1-som.dtb \ uniphier-pxs3-ref.dtb \ uniphier-pxs3-ref-gadget0.dtb \ uniphier-pxs3-ref-gadget1.dtb diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts b/arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts new file mode 100644 index 000000000000..dfdb39b68d44 --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts @@ -0,0 +1,83 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier NX1 Evaluation Board +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +/dts-v1/; +#include "uniphier-nx1.dtsi" + +/ { + model = "UniPhier NX1 Evaluation Board"; + compatible = "socionext,uniphier-nx1-evb", "socionext,uniphier-nx1"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + spi0 = &spi0; + ethernet = ð + }; + + memory@20000000 { + device_type = "memory"; + reg = <0 0x20000000 1 0x00000000>; + }; +}; + +&serial0 { + status = "okay"; +}; + +&serial1 { + status = "okay"; +}; + +&serial2 { + status = "okay"; +}; + +&serial3 { + status = "okay"; +}; + +&spi0 { + status = "okay"; +}; + +ð { + status = "okay"; + phy-handle = <ðphy>; +}; + +&mdio { + ethphy: ethphy@0 { + reg = <0>; + }; +}; + +&usb { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&sd { + status = "okay"; +}; + +&pinctrl_sd { + sd { + pins = "SDCLK", "SDCMD", "SDDAT0", + "SDDAT1", "SDDAT2", "SDDAT3"; + bias-pull-up; + }; +}; diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts new file mode 100644 index 000000000000..7c373eba7a81 --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts @@ -0,0 +1,109 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier NX1 Reference Board +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +/dts-v1/; +#include "uniphier-nx1-som.dts" + +/ { + model = "UniPhier NX1 Reference Board"; + compatible = "socionext,uniphier-nx1-ref", "socionext,uniphier-nx1"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + spi0 = &spi0; + spi1 = &spi1; + ethernet = ð + }; + + leds { + compatible = "gpio-leds"; + led0 { + label = "user0"; + gpios = <&pca9536 0 GPIO_ACTIVE_LOW>; + }; + + led1 { + label = "user1"; + gpios = <&pca9536 1 GPIO_ACTIVE_LOW>; + }; + + led2 { + label = "user2"; + gpios = <&pca9536 2 GPIO_ACTIVE_LOW>; + }; + + led3 { + label = "user3"; + gpios = <&pca9536 3 GPIO_ACTIVE_LOW>; + }; + }; + +}; + +&serial1 { + status = "okay"; +}; + +&serial2 { + status = "okay"; +}; + +&spi0 { + status = "okay"; +}; + +&spi1 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + pca9536: gpio@41 { + compatible = "ti,pca9536"; + reg = <0x41>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +ð { + status = "okay"; + phy-handle = <ðphy>; +}; + +&mdio { + ethphy: ethernet-phy@0 { + reg = <0>; + }; +}; + +&usb { + status = "okay"; +}; + +&pcie_ep { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts b/arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts new file mode 100644 index 000000000000..af7b9671dd2c --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts @@ -0,0 +1,50 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier NX1 SOM Board +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +/dts-v1/; +#include "uniphier-nx1.dtsi" + +/ { + model = "UniPhier NX1 SOM Board"; + compatible = "socionext,uniphier-nx1-som", "socionext,uniphier-nx1"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + serial0 = &serial0; + i2c1 = &i2c1; + }; + + memory@20000000 { + device_type = "memory"; + reg = <0 0x20000000 1 0x00000000>; + }; +}; + +&serial0 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + eeprom@50 { + compatible = "st,24c64", "atmel,24c64"; + reg = <0x50>; + pagesize = <32>; + }; +}; + +&emmc { + status = "okay"; +}; + +&sd { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi new file mode 100644 index 000000000000..e401763de86e --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi @@ -0,0 +1,704 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier NX1 SoC +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/gpio/uniphier-gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "socionext,uniphier-nx1"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&gic>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0 0x000>; + clocks = <&sys_clk 33>; + enable-method = "psci"; + next-level-cache = <&l2>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0 0x001>; + clocks = <&sys_clk 33>; + enable-method = "psci"; + next-level-cache = <&l2>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0 0x002>; + clocks = <&sys_clk 33>; + enable-method = "psci"; + next-level-cache = <&l2>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0 0x003>; + clocks = <&sys_clk 33>; + enable-method = "psci"; + next-level-cache = <&l2>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + }; + + l2: l2-cache { + compatible = "cache"; + }; + }; + + cluster0_opp: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-78125000 { + opp-hz = /bits/ 64 <78125000>; + clock-latency-ns = <300>; + }; + opp-156250000 { + opp-hz = /bits/ 64 <156250000>; + clock-latency-ns = <300>; + }; + opp-312500000 { + opp-hz = /bits/ 64 <312500000>; + clock-latency-ns = <300>; + }; + opp-625000000 { + opp-hz = /bits/ 64 <625000000>; + clock-latency-ns = <300>; + }; + opp-1250000000 { + opp-hz = /bits/ 64 <1250000000>; + clock-latency-ns = <300>; + }; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + clocks { + refclk: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio UNIPHIER_GPIO_PORT(3, 0) GPIO_ACTIVE_LOW>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>; + }; + + thermal-zones { + cpu-thermal { + polling-delay-passive = <250>; /* 250ms */ + polling-delay = <1000>; /* 1000ms */ + thermal-sensors = <&pvtctl>; + + trips { + cpu_crit: cpu-crit { + temperature = <120000>; /* 120C */ + hysteresis = <2000>; + type = "critical"; + }; + cpu_alert: cpu-alert { + temperature = <110000>; /* 110C */ + hysteresis = <2000>; + type = "passive"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure-memory@21000000 { + reg = <0x0 0x21000000 0x0 0x01000000>; + no-map; + }; + }; + + soc@0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + + sysctrl: sysctrl@11840000 { + compatible = "socionext,uniphier-nx1-sysctrl", + "simple-mfd", "syscon"; + reg = <0x11840000 0x10000>; + + sys_clk: clock { + compatible = "socionext,uniphier-nx1-clock"; + #clock-cells = <1>; + }; + + sys_rst: reset { + compatible = "socionext,uniphier-nx1-reset"; + #reset-cells = <1>; + }; + + watchdog { + compatible = "socionext,uniphier-wdt"; + }; + + pvtctl: thermal-sensor { + compatible = "socionext,uniphier-nx1-thermal"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + #thermal-sensor-cells = <0>; + socionext,tmod-calibration = <0x0f22 0x68ee>; + }; + }; + + spi0: spi@14006000 { + compatible = "socionext,uniphier-scssi"; + status = "disabled"; + reg = <0x14006000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0>; + clocks = <&peri_clk 11>; + resets = <&peri_rst 11>; + }; + + spi1: spi@14006100 { + compatible = "socionext,uniphier-scssi"; + status = "disabled"; + reg = <0x14006100 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + clocks = <&peri_clk 12>; + resets = <&peri_rst 12>; + }; + + serial0: serial@14006800 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x14006800 0x40>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + clocks = <&peri_clk 0>; + resets = <&peri_rst 0>; + }; + + serial1: serial@14006900 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x14006900 0x40>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + clocks = <&peri_clk 1>; + resets = <&peri_rst 1>; + }; + + serial2: serial@14006a00 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x14006a00 0x40>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + clocks = <&peri_clk 2>; + resets = <&peri_rst 2>; + }; + + serial3: serial@14006b00 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x14006b00 0x40>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + clocks = <&peri_clk 3>; + resets = <&peri_rst 3>; + }; + + gpio: gpio@14007000 { + compatible = "socionext,uniphier-gpio"; + reg = <0x14007000 0x200>; + interrupt-parent = <&aidet>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 0 0>, + <&pinctrl 49 0 0>, + <&pinctrl 53 0 0>, + <&pinctrl 96 0 0>, + <&pinctrl 120 0 0>; + gpio-ranges-group-names = "gpio_range0", + "gpio_range1", + "gpio_range2", + "gpio_range3", + "gpio_range4"; + ngpios = <126>; + socionext,interrupt-ranges = <0 48 6>; + }; + + eth: ethernet@15000000 { + compatible = "socionext,uniphier-nx1-ave4"; + status = "disabled"; + reg = <0x15000000 0x8500>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ether_rgmii>; + clock-names = "ether"; + clocks = <&sys_clk 6>; + reset-names = "ether"; + resets = <&sys_rst 6>; + phy-mode = "rgmii-id"; + local-mac-address = [00 00 00 00 00 00]; + socionext,syscon-phy-mode = <&soc_glue 0>; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + usb: usb@15a00000 { + compatible = "socionext,uniphier-dwc3", "snps,dwc3"; + status = "disabled"; + reg = <0x15a00000 0xcd00>; + interrupt-names = "host"; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>; + clock-names = "ref", "bus_early", "suspend"; + clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>; + resets = <&usb_rst 15>; + phys = <&usb_hsphy0>, <&usb_hsphy1>, + <&usb_ssphy0>, <&usb_ssphy1>; + dr_mode = "host"; + }; + + usb-controller@15b00000 { + compatible = "socionext,uniphier-nx1-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x15b00000 0x400>; + + usb_rst: reset@0 { + compatible = "socionext,uniphier-nx1-usb3-reset"; + reg = <0x0 0x4>; + #reset-cells = <1>; + clock-names = "link"; + clocks = <&sys_clk 12>; + reset-names = "link"; + resets = <&sys_rst 12>; + }; + + usb_vbus0: regulator@100 { + compatible = "socionext,uniphier-nx1-usb3-regulator"; + reg = <0x100 0x10>; + clock-names = "link"; + clocks = <&sys_clk 12>; + reset-names = "link"; + resets = <&sys_rst 12>; + }; + + usb_vbus1: regulator@110 { + compatible = "socionext,uniphier-nx1-usb3-regulator"; + reg = <0x110 0x10>; + clock-names = "link"; + clocks = <&sys_clk 12>; + reset-names = "link"; + resets = <&sys_rst 12>; + }; + + usb_hsphy0: hs-phy@200 { + compatible = "socionext,uniphier-nx1-usb3-hsphy"; + reg = <0x200 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy", "phy-ext"; + clocks = <&sys_clk 12>, <&sys_clk 16>, + <&sys_clk 13>; + reset-names = "link", "phy"; + resets = <&sys_rst 12>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + }; + + usb_hsphy1: hs-phy@210 { + compatible = "socionext,uniphier-nx1-usb3-hsphy"; + reg = <0x210 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy", "phy-ext"; + clocks = <&sys_clk 12>, <&sys_clk 16>, + <&sys_clk 13>; + reset-names = "link", "phy"; + resets = <&sys_rst 12>, <&sys_rst 16>; + vbus-supply = <&usb_vbus1>; + }; + + usb_ssphy0: ss-phy@300 { + compatible = "socionext,uniphier-nx1-usb3-ssphy"; + reg = <0x300 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy", "phy-ext"; + clocks = <&sys_clk 12>, <&sys_clk 17>, + <&sys_clk 13>; + reset-names = "link", "phy"; + resets = <&sys_rst 12>, <&sys_rst 17>; + vbus-supply = <&usb_vbus0>; + }; + + usb_ssphy1: ss-phy@310 { + compatible = "socionext,uniphier-nx1-usb3-ssphy"; + reg = <0x310 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy", "phy-ext"; + clocks = <&sys_clk 12>, <&sys_clk 18>, + <&sys_clk 13>; + reset-names = "link", "phy"; + resets = <&sys_rst 12>, <&sys_rst 18>; + vbus-supply = <&usb_vbus1>; + }; + }; + + pcie: pcie@16000000 { + compatible = "socionext,uniphier-pcie"; + status = "disabled"; + reg-names = "dbi", "link", "config", "atu"; + reg = <0x16000000 0x1000>, <0x179a0000 0x10000>, + <0x0fff0000 0x10000>, <0x16300000 0x1000>; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + num-lanes = <2>; + num-viewport = <1>; + bus-range = <0x0 0xff>; + device_type = "pci"; + ranges = + /* downstream I/O */ + <0x81000000 0 0x00000000 0x0ffe0000 0 0x00010000>, + /* non-prefetchable memory */ + <0x82000000 0 0x20000000 0x04200000 0 0x0bde0000>; + #interrupt-cells = <1>; + interrupt-names = "dma", "msi"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ + <0 0 0 2 &pcie_intc 1>, /* INTB */ + <0 0 0 3 &pcie_intc 2>, /* INTC */ + <0 0 0 4 &pcie_intc 3>; /* INTD */ + phy-names = "pcie-phy"; + phys = <&pcie_phy>; + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + pcie_ep: pcie-ep@16000000 { + compatible = "socionext,uniphier-nx1-pcie-ep"; + status = "disabled"; + reg-names = "dbi", "dbi2", "link", "addr_space", "atu"; + reg = <0x16000000 0x1000>, <0x16100000 0x1000>, + <0x179a0000 0x10000>, <0x04200000 0xbe00000>, + <0x16300000 0x1000>; + clock-names = "link"; + clocks = <&sys_clk 24>; + reset-names = "link"; + resets = <&sys_rst 24>; + num-ib-windows = <16>; + num-ob-windows = <16>; + num-lanes = <2>; + phy-names = "pcie-phy"; + phys = <&pcie_phy>; + }; + + pcie_phy: phy@179b8000 { + compatible = "socionext,uniphier-nx1-pcie-phy"; + reg = <0x179b8000 0x4000>; + #phy-cells = <0>; + clock-names = "link"; + clocks = <&sys_clk 24>; + reset-names = "link"; + resets = <&sys_rst 24>; + socionext,syscon = <&sysctrl>; + }; + + i2c0: i2c@18780000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&peri_clk 4>; + resets = <&peri_rst 4>; + clock-frequency = <400000>; + }; + + i2c1: i2c@18781000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18781000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&peri_clk 5>; + resets = <&peri_rst 5>; + clock-frequency = <400000>; + }; + + i2c2: i2c@18782000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18782000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clocks = <&peri_clk 6>; + resets = <&peri_rst 6>; + clock-frequency = <400000>; + }; + + i2c3: i2c@18783000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18783000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&peri_clk 7>; + resets = <&peri_rst 7>; + clock-frequency = <400000>; + }; + + i2c4: i2c@18784000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18784000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + clocks = <&peri_clk 8>; + resets = <&peri_rst 8>; + clock-frequency = <100000>; + }; + + i2c5: i2c@18785000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18785000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c5>; + clocks = <&peri_clk 9>; + resets = <&peri_rst 9>; + clock-frequency = <100000>; + }; + + i2c6: i2c@18786000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x18786000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c6>; + clocks = <&peri_clk 10>; + resets = <&peri_rst 10>; + clock-frequency = <100000>; + }; + + sdctrl@19810000 { + compatible = "socionext,uniphier-nx1-sdctrl", + "simple-mfd", "syscon"; + reg = <0x19810000 0x400>; + + sd_clk: clock { + compatible = "socionext,uniphier-nx1-sd-clock"; + #clock-cells = <1>; + }; + + sd_rst: reset { + compatible = "socionext,uniphier-nx1-sd-reset"; + #reset-cells = <1>; + }; + }; + + perictrl@19820000 { + compatible = "socionext,uniphier-nx1-perictrl", + "simple-mfd", "syscon"; + reg = <0x19820000 0x200>; + + peri_clk: clock { + compatible = "socionext,uniphier-nx1-peri-clock"; + #clock-cells = <1>; + }; + + peri_rst: reset { + compatible = "socionext,uniphier-nx1-peri-reset"; + #reset-cells = <1>; + }; + }; + + emmc: mmc@1a000000 { + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; + reg = <0x1a000000 0x400>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_emmc>; + clocks = <&sys_clk 4>; + resets = <&sys_rst 4>; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-pwrseq = <&emmc_pwrseq>; + cdns,phy-input-delay-legacy = <9>; + cdns,phy-input-delay-mmc-highspeed = <2>; + cdns,phy-input-delay-mmc-ddr = <3>; + cdns,phy-dll-delay-sdclk = <21>; + cdns,phy-dll-delay-sdclk-hsmmc = <21>; + }; + + sd: mmc@1a400000 { + compatible = "socionext,uniphier-sd-v3.1.1"; + status = "disabled"; + reg = <0x1a400000 0x800>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sd>; + clocks = <&sd_clk 0>; + reset-names = "host"; + resets = <&sd_rst 0>; + bus-width = <4>; + cap-sd-highspeed; + }; + + soc_glue: soc-glue@1f800000 { + compatible = "socionext,uniphier-nx1-soc-glue", + "simple-mfd", "syscon"; + reg = <0x1f800000 0x2000>; + + pinctrl: pinctrl { + compatible = "socionext,uniphier-nx1-pinctrl"; + }; + }; + + soc-glue@1f900000 { + compatible = "socionext,uniphier-nx1-soc-glue-debug", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1f900000 0x2000>; + }; + + xdmac: dma-controller@1fa10000 { + compatible = "socionext,uniphier-xdmac"; + reg = <0x1fa10000 0x5300>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + dma-channels = <16>; + #dma-cells = <2>; + }; + + aidet: aidet@1fb20000 { + compatible = "socionext,uniphier-nx1-aidet"; + reg = <0x1fb20000 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gic: interrupt-controller@1fd00000 { + compatible = "arm,gic-v3"; + reg = <0x1fd00000 0x10000>, /* GICD */ + <0x1fd80000 0x80000>; /* GICR */ + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + }; +}; + +#include "uniphier-pinctrl.dtsi"
Initial version of devicetree sources for NX1 SoC and boards. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> --- arch/arm64/boot/dts/socionext/Makefile | 3 + .../boot/dts/socionext/uniphier-nx1-evb.dts | 83 +++ .../boot/dts/socionext/uniphier-nx1-ref.dts | 109 +++ .../boot/dts/socionext/uniphier-nx1-som.dts | 50 ++ .../boot/dts/socionext/uniphier-nx1.dtsi | 704 ++++++++++++++++++ 5 files changed, 949 insertions(+) create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi