[v6,0/5] add Tegra194 XUSB host and pad controller support

Message

JC Kuo Feb. 12, 2020, 6:11 a.m. UTC

v6:
  phy: tegra: xusb: Protect Tegra186 soc with config
   - no change

  phy: tegra: xusb: Add Tegra194 support
   - no change

  dt-bindings: phy: tegra: Add Tegra194 support
   - no change

  arm64: tegra: Add XUSB and pad controller on Tegra194
   - rebased

  arm64: tegra: Enable XUSB host in P2972-0000 board
   - re-use "maximum-speed" instead of adding "nvidia,disable-gen2"

v5:
  phy: tegra: xusb: Protect Tegra186 soc with config
   - no change

  phy: tegra: xusb: Add Tegra194 support
   - re-use "maximum-speed" instead of adding "nvidia,disable-gen2"

  dt-bindings: phy: tegra: Add Tegra194 support
   - re-use "maximum-speed" instead of adding "nvidia,disable-gen2"

  arm64: tegra: Add XUSB and pad controller on Tegra194
   - no change

  arm64: tegra: Enable XUSB host in P2972-0000 board
   - no change

v3:
  add change log to cover latter

v2:
  xhci: tegra: Parameterize mailbox register addresses
   - no change

  usb: host: xhci-tegra: Add Tegra194 XHCI support
   - no change

  phy: tegra: xusb: Protect Tegra186 soc with config
   - new patch to protect Tegra186 soc data with config

  phy: tegra: xusb: Add Tegra194 support
   - removed unnecessary #if/#endif pairs
   - introduce new soc->supports_gen2 flag which indicate whether or not 
     a soc supports USB 3.1 Gen 2 speed

  dt-bindings: phy: tegra: Add Tegra194 support
   - fix a typo

  arm64: tegra: Add XUSB and pad controller on Tegra194
   - renamed xhci@3610000 with usb@3610000
   - moved padctl@3520000 and usb@3610000 inside /cbb
   - cleaned up "clocks" property of usb@3610000 node
   - added blanks lines to visually separate blocks

  arm64: tegra: Enable XUSB host in P2972-0000 board
   - use capitalization of regulator names
   - fix gpio property of VDD_5V_SATA regulator


JC Kuo (5):
  phy: tegra: xusb: Protect Tegra186 soc with config
  phy: tegra: xusb: Add Tegra194 support
  dt-bindings: phy: tegra: Add Tegra194 support
  arm64: tegra: Add XUSB and pad controller on Tegra194
  arm64: tegra: Enable XUSB host in P2972-0000 board

 .../phy/nvidia,tegra124-xusb-padctl.txt       |  18 +++
 .../arm64/boot/dts/nvidia/tegra194-p2888.dtsi |  36 ++++-
 .../boot/dts/nvidia/tegra194-p2972-0000.dts   |  63 ++++++++
 arch/arm64/boot/dts/nvidia/tegra194.dtsi      | 139 +++++++++++++++++
 drivers/phy/tegra/Makefile                    |   1 +
 drivers/phy/tegra/xusb-tegra186.c             | 143 +++++++++++++-----
 drivers/phy/tegra/xusb.c                      |  17 +++
 drivers/phy/tegra/xusb.h                      |   5 +
 8 files changed, 387 insertions(+), 35 deletions(-)