new file mode 100644
@@ -0,0 +1,9 @@
+What: /sys/bus/platform/drivers/eud/.../enable
+Date: February 2022
+Contact: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+ The Enable/Disable sysfs interface for Embedded
+ USB Debugger(EUD). This enables and disables the
+ EUD based on a 1 or a 0 value. By enabling EUD,
+ the user is able to activate the mini-usb hub of
+ EUD for debug and trace capabilities.
@@ -137,6 +137,16 @@ config USB_APPLEDISPLAY
Say Y here if you want to control the backlight of Apple Cinema
Displays over USB. This driver provides a sysfs interface.
+config USB_QCOM_EUD
+ tristate "QCOM Embedded USB Debugger(EUD) Driver"
+ select USB_ROLE_SWITCH
+ help
+ This module enables support for Qualcomm Technologies, Inc.
+ Embedded USB Debugger (EUD). The EUD is a control peripheral
+ which reports VBUS attach/detach events and has USB-based
+ debug and trace capabilities. On selecting m, the module name
+ that is built is qcom_eud.ko
+
config APPLE_MFI_FASTCHARGE
tristate "Fast charge control for iOS devices"
select POWER_SUPPLY
@@ -18,6 +18,7 @@ obj-$(CONFIG_USB_ISIGHTFW) += isight_firmware.o
obj-$(CONFIG_USB_LCD) += usblcd.o
obj-$(CONFIG_USB_LD) += ldusb.o
obj-$(CONFIG_USB_LEGOTOWER) += legousbtower.o
+obj-$(CONFIG_USB_QCOM_EUD) += qcom_eud.o
obj-$(CONFIG_USB_TEST) += usbtest.o
obj-$(CONFIG_USB_EHSET_TEST_FIXTURE) += ehset.o
obj-$(CONFIG_USB_TRANCEVIBRATOR) += trancevibrator.o
new file mode 100644
@@ -0,0 +1,251 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015-2021, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/sysfs.h>
+#include <linux/usb/role.h>
+
+#define EUD_REG_INT1_EN_MASK 0x0024
+#define EUD_REG_INT_STATUS_1 0x0044
+#define EUD_REG_CTL_OUT_1 0x0074
+#define EUD_REG_VBUS_INT_CLR 0x0080
+#define EUD_REG_CSR_EUD_EN 0x1014
+#define EUD_REG_SW_ATTACH_DET 0x1018
+#define EUD_REG_EUD_EN2 0x0000
+
+#define EUD_ENABLE BIT(0)
+#define EUD_INT_PET_EUD BIT(0)
+#define EUD_INT_VBUS BIT(2)
+#define EUD_INT_SAFE_MODE BIT(4)
+#define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE)
+
+struct eud_chip {
+ struct device *dev;
+ struct usb_role_switch *role_sw;
+ void __iomem *base;
+ void __iomem *mode_mgr;
+ unsigned int int_status;
+ int irq;
+ bool enabled;
+ bool usb_attached;
+};
+
+static int enable_eud(struct eud_chip *priv)
+{
+ writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN);
+ writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE,
+ priv->base + EUD_REG_INT1_EN_MASK);
+ writel(1, priv->mode_mgr + EUD_REG_EUD_EN2);
+
+ return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE);
+}
+
+static void disable_eud(struct eud_chip *priv)
+{
+ writel(0, priv->base + EUD_REG_CSR_EUD_EN);
+ writel(0, priv->mode_mgr + EUD_REG_EUD_EN2);
+}
+
+static ssize_t enable_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct eud_chip *chip = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%d\n", chip->enabled);
+}
+
+static ssize_t enable_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct eud_chip *chip = dev_get_drvdata(dev);
+ bool enable;
+ int ret;
+
+ if (kstrtobool(buf, &enable))
+ return -EINVAL;
+
+ if (enable) {
+ ret = enable_eud(chip);
+ if (!ret)
+ chip->enabled = enable;
+ else
+ disable_eud(chip);
+ } else {
+ disable_eud(chip);
+ }
+
+ return count;
+}
+
+static DEVICE_ATTR_RW(enable);
+
+static struct attribute *eud_attrs[] = {
+ &dev_attr_enable.attr,
+ NULL,
+};
+ATTRIBUTE_GROUPS(eud);
+
+static void usb_attach_detach(struct eud_chip *chip)
+{
+ u32 reg;
+
+ /* read ctl_out_1[4] to find USB attach or detach event */
+ reg = readl(chip->base + EUD_REG_CTL_OUT_1);
+ chip->usb_attached = reg & EUD_INT_SAFE_MODE;
+}
+
+static void pet_eud(struct eud_chip *chip)
+{
+ u32 reg;
+ int ret;
+
+ /* When the EUD_INT_PET_EUD in SW_ATTACH_DET is set, the cable has been
+ * disconnected and we need to detach the pet to check if EUD is in safe
+ * mode before attaching again.
+ */
+ reg = readl(chip->base + EUD_REG_SW_ATTACH_DET);
+ if (reg & EUD_INT_PET_EUD) {
+ /* Detach & Attach pet for EUD */
+ writel(0, chip->base + EUD_REG_SW_ATTACH_DET);
+ /* Delay to make sure detach pet is done before attach pet */
+ ret = readl_poll_timeout(chip->base + EUD_REG_SW_ATTACH_DET,
+ reg, (reg == 0), 1, 100);
+ if (ret) {
+ dev_err(chip->dev, "Detach pet failed\n");
+ return;
+ }
+ }
+ /* Attach pet for EUD */
+ writel(EUD_INT_PET_EUD, chip->base + EUD_REG_SW_ATTACH_DET);
+}
+
+static irqreturn_t handle_eud_irq(int irq, void *data)
+{
+ struct eud_chip *chip = data;
+ u32 reg;
+
+ reg = readl(chip->base + EUD_REG_INT_STATUS_1);
+ switch (reg & EUD_INT_ALL) {
+ case EUD_INT_VBUS:
+ usb_attach_detach(chip);
+ return IRQ_WAKE_THREAD;
+ case EUD_INT_SAFE_MODE:
+ pet_eud(chip);
+ return IRQ_HANDLED;
+ default:
+ return IRQ_NONE;
+ }
+}
+
+static irqreturn_t handle_eud_irq_thread(int irq, void *data)
+{
+ struct eud_chip *chip = data;
+ int ret;
+
+ if (chip->usb_attached)
+ ret = usb_role_switch_set_role(chip->role_sw, USB_ROLE_DEVICE);
+ else
+ ret = usb_role_switch_set_role(chip->role_sw, USB_ROLE_HOST);
+ if (ret)
+ dev_err(chip->dev, "failed to set role switch\n");
+
+ /* set and clear vbus_int_clr[0] to clear interrupt */
+ writel(BIT(0), chip->base + EUD_REG_VBUS_INT_CLR);
+ writel(0, chip->base + EUD_REG_VBUS_INT_CLR);
+
+ return IRQ_HANDLED;
+}
+
+static void eud_role_switch_release(void *data)
+{
+ struct eud_chip *chip = data;
+
+ usb_role_switch_put(chip->role_sw);
+}
+
+static int eud_probe(struct platform_device *pdev)
+{
+ struct eud_chip *chip;
+ int ret;
+
+ chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ chip->dev = &pdev->dev;
+
+ ret = devm_add_action_or_reset(chip->dev, eud_role_switch_release, chip);
+ if (ret)
+ return dev_err_probe(chip->dev, ret,
+ "failed to add role switch release action\n");
+
+ chip->role_sw = usb_role_switch_get(&pdev->dev);
+ if (IS_ERR(chip->role_sw))
+ return dev_err_probe(chip->dev, PTR_ERR(chip->role_sw),
+ "failed to get role switch\n");
+
+ chip->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(chip->base))
+ return PTR_ERR(chip->base);
+
+ chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1);
+ if (IS_ERR(chip->mode_mgr))
+ return PTR_ERR(chip->mode_mgr);
+
+ chip->irq = platform_get_irq(pdev, 0);
+ ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq,
+ handle_eud_irq_thread, IRQF_ONESHOT, NULL, chip);
+ if (ret)
+ return dev_err_probe(chip->dev, ret, "failed to allocate irq\n");
+
+ enable_irq_wake(chip->irq);
+
+ platform_set_drvdata(pdev, chip);
+
+ return 0;
+}
+
+static int eud_remove(struct platform_device *pdev)
+{
+ struct eud_chip *chip = platform_get_drvdata(pdev);
+
+ if (chip->enabled)
+ disable_eud(chip);
+
+ device_init_wakeup(&pdev->dev, false);
+ disable_irq_wake(chip->irq);
+
+ return 0;
+}
+
+static const struct of_device_id eud_dt_match[] = {
+ { .compatible = "qcom,sc7280-eud" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, eud_dt_match);
+
+static struct platform_driver eud_driver = {
+ .probe = eud_probe,
+ .remove = eud_remove,
+ .driver = {
+ .name = "qcom_eud",
+ .dev_groups = eud_groups,
+ .of_match_table = eud_dt_match,
+ },
+};
+module_platform_driver(eud_driver);
+
+MODULE_DESCRIPTION("QTI EUD driver");
+MODULE_LICENSE("GPL v2");
Add support for control peripheral of EUD (Embedded USB Debugger) to listen to events such as USB attach/detach, pet EUD to indicate software is functional.Reusing the platform device kobj, sysfs entry 'enable' is created to enable or disable EUD. To enable the eud the following needs to be done echo 1 > /sys/bus/platform/.../enable To disable eud, following is the command echo 0 > /sys/bus/platform/.../enable Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com> --- Documentation/ABI/testing/sysfs-driver-eud | 9 ++ drivers/usb/misc/Kconfig | 10 ++ drivers/usb/misc/Makefile | 1 + drivers/usb/misc/qcom_eud.c | 251 +++++++++++++++++++++++++++++ 4 files changed, 271 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-eud create mode 100644 drivers/usb/misc/qcom_eud.c -- 2.7.4