| Message ID | 1540661892-189850-1-git-send-email-george.cherian@cavium.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | xhci: Add quirk to workaround the errata seen on Cavium Thunder-X2 Soc | expand |
On Sat, 27 Oct 2018, Cherian, George wrote: > Implement workaround for ThunderX2 Errata-129 (documented in > CN99XX Known Issues" available at Cavium support site). > As per ThunderX2errata-129, USB-2.0 device may come up as USB-1.0 > If a connection to a USB-1.0 device is followed by another connection > to a USB-2.0 device, the link will come up as USB-1.0 for the USB-2.0 > device. > > Resolution: Reset the PHY after the USB1.0 device is disconnected. > The PHY reset sequence is done using private registers in XHCI register > space. After the PHY is reset we check for the PLL lock status and retry > the operation if it fails. From our tests, retrying 4 times is sufficient. > > Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround > in handle_xhci_port_status(). Minor nitpick (for both the patch description and the code comments): USB 1.0 was never widely adopted and is not used any more. The earliest vesion of USB currently used in supported devices is USB 1.1. Likewise, there are a few devices around that support USB 2.1, not USB 2.0, but they are presumably also subject to the problem described above. I suggest you change the description and the comments to refer to USB 1 and USB 2 instead of USB 1.0 and USB 2.0, as the latter are too restrictive and misleading. Alan Stern
Hi Alan, Thanks for the review. I will update the patch accordingly and send out v2. On 10/28/2018 10:48 PM, Alan Stern wrote: > > On Sat, 27 Oct 2018, Cherian, George wrote: > >> Implement workaround for ThunderX2 Errata-129 (documented in >> CN99XX Known Issues" available at Cavium support site). >> As per ThunderX2errata-129, USB-2.0 device may come up as USB-1.0 >> If a connection to a USB-1.0 device is followed by another connection >> to a USB-2.0 device, the link will come up as USB-1.0 for the USB-2.0 >> device. >> >> Resolution: Reset the PHY after the USB1.0 device is disconnected. >> The PHY reset sequence is done using private registers in XHCI register >> space. After the PHY is reset we check for the PLL lock status and retry >> the operation if it fails. From our tests, retrying 4 times is sufficient. >> >> Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround >> in handle_xhci_port_status(). > > Minor nitpick (for both the patch description and the code comments): > > USB 1.0 was never widely adopted and is not used any more. The > earliest vesion of USB currently used in supported devices is USB 1.1. > Likewise, there are a few devices around that support USB 2.1, not > USB 2.0, but they are presumably also subject to the problem described > above. > > I suggest you change the description and the comments to refer to USB 1 > and USB 2 instead of USB 1.0 and USB 2.0, as the latter are too > restrictive and misleading. > > Alan Stern > Regards, -George
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 51dd8e0..334c009 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -231,6 +231,11 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) if (pdev->vendor == PCI_VENDOR_ID_TI && pdev->device == 0x8241) xhci->quirks |= XHCI_LIMIT_ENDPOINT_INTERVAL_7; + if ((pdev->vendor == PCI_VENDOR_ID_BROADCOM || + pdev->vendor == PCI_VENDOR_ID_CAVIUM) && + pdev->device == 0x9026) + xhci->quirks |= XHCI_RESET_PLL_ON_DISCONNECT; + if (xhci->quirks & XHCI_RESET_ON_RESUME) xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, "QUIRK: Resetting on resume"); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index f0a99aa..f342cbd 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1517,6 +1517,35 @@ static void handle_device_notification(struct xhci_hcd *xhci, usb_wakeup_notification(udev->parent, udev->portnum); } +/* + * Quirk hanlder for errata seen on Cavium ThunderX2 processor XHCI + * Controller. + * As per ThunderX2errata-129 USB2.0 device may come up as USB1.0 + * If a connection to a USB1.0 device is followed by another connection + * to a USB2.0 device. + * + * Reset the PHY after the USB device is disconnected if device speed + * is less than HCD_USB3. + * Retry the reset sequence max of 4 times checking the PLL lock status. + * + */ +static void xhci_handle_tx2_wrapper_reset(struct xhci_hcd *xhci) +{ + struct usb_hcd *hcd = xhci_to_hcd(xhci); + u32 pll_lock_check; + u32 retry_count = 4; + + do { + /* Assert PHY reset */ + writel(0x6F, hcd->regs + 0x1048); + udelay(10); + /* De-assert the PHY reset */ + writel(0x7F, hcd->regs + 0x1048); + udelay(200); + pll_lock_check = readl(hcd->regs + 0x1070); + } while (!(pll_lock_check & 0x1) && --retry_count); +} + static void handle_port_status(struct xhci_hcd *xhci, union xhci_trb *event) { @@ -1642,8 +1671,12 @@ static void handle_port_status(struct xhci_hcd *xhci, goto cleanup; } - if (hcd->speed < HCD_USB3) + if (hcd->speed < HCD_USB3) { xhci_test_and_clear_bit(xhci, port, PORT_PLC); + if ((portsc & PORT_CSC) && !(portsc & 0x1) && + (xhci->quirks & XHCI_RESET_PLL_ON_DISCONNECT)) + xhci_handle_tx2_wrapper_reset(xhci); + } cleanup: /* Update event ring dequeue pointer before dropping the lock */ diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 6230a57..004b832 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1846,6 +1846,7 @@ struct xhci_hcd { #define XHCI_SUSPEND_DELAY BIT_ULL(30) #define XHCI_INTEL_USB_ROLE_SW BIT_ULL(31) #define XHCI_ZERO_64B_REGS BIT_ULL(32) +#define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(33) unsigned int num_active_eps; unsigned int limit_active_eps;
Implement workaround for ThunderX2 Errata-129 (documented in CN99XX Known Issues" available at Cavium support site). As per ThunderX2errata-129, USB-2.0 device may come up as USB-1.0 If a connection to a USB-1.0 device is followed by another connection to a USB-2.0 device, the link will come up as USB-1.0 for the USB-2.0 device. Resolution: Reset the PHY after the USB1.0 device is disconnected. The PHY reset sequence is done using private registers in XHCI register space. After the PHY is reset we check for the PLL lock status and retry the operation if it fails. From our tests, retrying 4 times is sufficient. Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround in handle_xhci_port_status(). Signed-off-by: George Cherian <george.cherian@cavium.com> --- drivers/usb/host/xhci-pci.c | 5 +++++ drivers/usb/host/xhci-ring.c | 35 ++++++++++++++++++++++++++++++++++- drivers/usb/host/xhci.h | 1 + 3 files changed, 40 insertions(+), 1 deletion(-)