| Message ID | 1662480933-12326-3-git-send-email-quic_kriskura@quicinc.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | df2217ff17a8207295e77ec12a858545633bf4cb |
| Headers | show |
| Series | Add QCOM SNPS PHY overriding params support | expand |
On Tue, Sep 06, 2022 at 09:45:32PM +0530, Krishna Kurapati wrote: > Add support for overriding electrical signal tuning parameters for > SNPS HS Phy. > Reviewed-by: Bjorn Andersson <andersson@kernel.org> Regards, Bjorn > Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 255 +++++++++++++++++++++++++- > 1 file changed, 253 insertions(+), 2 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c > index 5d20378..2502294 100644 > --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c > +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c > @@ -52,6 +52,12 @@ > #define USB2_SUSPEND_N BIT(2) > #define USB2_SUSPEND_N_SEL BIT(3) > > +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0 (0x6c) > +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1 (0x70) > +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2 (0x74) > +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3 (0x78) > +#define PARAM_OVRD_MASK 0xFF > + > #define USB2_PHY_USB_PHY_CFG0 (0x94) > #define UTMI_PHY_DATAPATH_CTRL_OVERRIDE_EN BIT(0) > #define UTMI_PHY_CMN_CTRL_OVERRIDE_EN BIT(1) > @@ -60,12 +66,47 @@ > #define REFCLK_SEL_MASK GENMASK(1, 0) > #define REFCLK_SEL_DEFAULT (0x2 << 0) > > +#define HS_DISCONNECT_MASK GENMASK(2, 0) > +#define SQUELCH_DETECTOR_MASK GENMASK(7, 5) > + > +#define HS_AMPLITUDE_MASK GENMASK(3, 0) > +#define PREEMPHASIS_DURATION_MASK BIT(5) > +#define PREEMPHASIS_AMPLITUDE_MASK GENMASK(7, 6) > + > +#define HS_RISE_FALL_MASK GENMASK(1, 0) > +#define HS_CROSSOVER_VOLTAGE_MASK GENMASK(3, 2) > +#define HS_OUTPUT_IMPEDANCE_MASK GENMASK(5, 4) > + > +#define LS_FS_OUTPUT_IMPEDANCE_MASK GENMASK(3, 0) > + > static const char * const qcom_snps_hsphy_vreg_names[] = { > "vdda-pll", "vdda33", "vdda18", > }; > > #define SNPS_HS_NUM_VREGS ARRAY_SIZE(qcom_snps_hsphy_vreg_names) > > +struct override_param { > + s32 value; > + u8 reg_val; > +}; > + > +struct override_param_map { > + const char *prop_name; > + const struct override_param *param_table; > + u8 table_size; > + u8 reg_offset; > + u8 param_mask; > +}; > + > +struct phy_override_seq { > + bool need_update; > + u8 offset; > + u8 value; > + u8 mask; > +}; > + > +#define NUM_HSPHY_TUNING_PARAMS (9) > + > /** > * struct qcom_snps_hsphy - snps hs phy attributes > * > @@ -91,6 +132,7 @@ struct qcom_snps_hsphy { > > bool phy_initialized; > enum phy_mode mode; > + struct phy_override_seq update_seq_cfg[NUM_HSPHY_TUNING_PARAMS]; > }; > > static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, > @@ -173,10 +215,158 @@ static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode, > return 0; > } > > +static const struct override_param hs_disconnect_sc7280[] = { > + { -272, 0 }, > + { 0, 1 }, > + { 317, 2 }, > + { 630, 3 }, > + { 973, 4 }, > + { 1332, 5 }, > + { 1743, 6 }, > + { 2156, 7 }, > +}; > + > +static const struct override_param squelch_det_threshold_sc7280[] = { > + { -2090, 7 }, > + { -1560, 6 }, > + { -1030, 5 }, > + { -530, 4 }, > + { 0, 3 }, > + { 530, 2 }, > + { 1060, 1 }, > + { 1590, 0 }, > +}; > + > +static const struct override_param hs_amplitude_sc7280[] = { > + { -660, 0 }, > + { -440, 1 }, > + { -220, 2 }, > + { 0, 3 }, > + { 230, 4 }, > + { 440, 5 }, > + { 650, 6 }, > + { 890, 7 }, > + { 1110, 8 }, > + { 1330, 9 }, > + { 1560, 10 }, > + { 1780, 11 }, > + { 2000, 12 }, > + { 2220, 13 }, > + { 2430, 14 }, > + { 2670, 15 }, > +}; > + > +static const struct override_param preemphasis_duration_sc7280[] = { > + { 10000, 1 }, > + { 20000, 0 }, > +}; > + > +static const struct override_param preemphasis_amplitude_sc7280[] = { > + { 10000, 1 }, > + { 20000, 2 }, > + { 30000, 3 }, > + { 40000, 0 }, > +}; > + > +static const struct override_param hs_rise_fall_time_sc7280[] = { > + { -4100, 3 }, > + { 0, 2 }, > + { 2810, 1 }, > + { 5430, 0 }, > +}; > + > +static const struct override_param hs_crossover_voltage_sc7280[] = { > + { -31000, 1 }, > + { 0, 3 }, > + { 28000, 2 }, > +}; > + > +static const struct override_param hs_output_impedance_sc7280[] = { > + { -2300000, 3 }, > + { 0, 2 }, > + { 2600000, 1 }, > + { 6100000, 0 }, > +}; > + > +static const struct override_param ls_fs_output_impedance_sc7280[] = { > + { -1053, 15 }, > + { -557, 7 }, > + { 0, 3 }, > + { 612, 1 }, > + { 1310, 0 }, > +}; > + > +static const struct override_param_map sc7280_snps_7nm_phy[] = { > + { > + "qcom,hs-disconnect-bp", > + hs_disconnect_sc7280, > + ARRAY_SIZE(hs_disconnect_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0, > + HS_DISCONNECT_MASK > + }, > + { > + "qcom,squelch-detector-bp", > + squelch_det_threshold_sc7280, > + ARRAY_SIZE(squelch_det_threshold_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0, > + SQUELCH_DETECTOR_MASK > + }, > + { > + "qcom,hs-amplitude-bp", > + hs_amplitude_sc7280, > + ARRAY_SIZE(hs_amplitude_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1, > + HS_AMPLITUDE_MASK > + }, > + { > + "qcom,pre-emphasis-duration-bp", > + preemphasis_duration_sc7280, > + ARRAY_SIZE(preemphasis_duration_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1, > + PREEMPHASIS_DURATION_MASK, > + }, > + { > + "qcom,pre-emphasis-amplitude-bp", > + preemphasis_amplitude_sc7280, > + ARRAY_SIZE(preemphasis_amplitude_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1, > + PREEMPHASIS_AMPLITUDE_MASK, > + }, > + { > + "qcom,hs-rise-fall-time-bp", > + hs_rise_fall_time_sc7280, > + ARRAY_SIZE(hs_rise_fall_time_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2, > + HS_RISE_FALL_MASK > + }, > + { > + "qcom,hs-crossover-voltage-microvolt", > + hs_crossover_voltage_sc7280, > + ARRAY_SIZE(hs_crossover_voltage_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2, > + HS_CROSSOVER_VOLTAGE_MASK > + }, > + { > + "qcom,hs-output-impedance-micro-ohms", > + hs_output_impedance_sc7280, > + ARRAY_SIZE(hs_output_impedance_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2, > + HS_OUTPUT_IMPEDANCE_MASK, > + }, > + { > + "qcom,ls-fs-output-impedance-bp", > + ls_fs_output_impedance_sc7280, > + ARRAY_SIZE(ls_fs_output_impedance_sc7280), > + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3, > + LS_FS_OUTPUT_IMPEDANCE_MASK, > + }, > + {}, > +}; > + > static int qcom_snps_hsphy_init(struct phy *phy) > { > struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy); > - int ret; > + int ret, i; > > dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__); > > @@ -223,6 +413,14 @@ static int qcom_snps_hsphy_init(struct phy *phy) > qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1, > VBUSVLDEXT0, VBUSVLDEXT0); > > + for (i = 0; i < ARRAY_SIZE(hsphy->update_seq_cfg); i++) { > + if (hsphy->update_seq_cfg[i].need_update) > + qcom_snps_hsphy_write_mask(hsphy->base, > + hsphy->update_seq_cfg[i].offset, > + hsphy->update_seq_cfg[i].mask, > + hsphy->update_seq_cfg[i].value); > + } > + > qcom_snps_hsphy_write_mask(hsphy->base, > USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2, > VREGBYPASS, VREGBYPASS); > @@ -280,7 +478,10 @@ static const struct phy_ops qcom_snps_hsphy_gen_ops = { > static const struct of_device_id qcom_snps_hsphy_of_match_table[] = { > { .compatible = "qcom,sm8150-usb-hs-phy", }, > { .compatible = "qcom,usb-snps-hs-5nm-phy", }, > - { .compatible = "qcom,usb-snps-hs-7nm-phy", }, > + { > + .compatible = "qcom,usb-snps-hs-7nm-phy", > + .data = &sc7280_snps_7nm_phy, > + }, > { .compatible = "qcom,usb-snps-femto-v2-phy", }, > { } > }; > @@ -291,6 +492,55 @@ static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = { > qcom_snps_hsphy_runtime_resume, NULL) > }; > > +static void qcom_snps_hsphy_override_param_update_val( > + const struct override_param_map map, > + s32 dt_val, struct phy_override_seq *seq_entry) > +{ > + int i; > + > + /* > + * Param table for each param is in increasing order > + * of dt values. We need to iterate over the list to > + * select the entry that matches the dt value and pick > + * up the corresponding register value. > + */ > + for (i = 0; i < map.table_size - 1; i++) { > + if (map.param_table[i].value == dt_val) > + break; > + } > + > + seq_entry->need_update = true; > + seq_entry->offset = map.reg_offset; > + seq_entry->mask = map.param_mask; > + seq_entry->value = map.param_table[i].reg_val << __ffs(map.param_mask); > +} > + > +static void qcom_snps_hsphy_read_override_param_seq(struct device *dev) > +{ > + struct device_node *node = dev->of_node; > + s32 val; > + int ret, i; > + struct qcom_snps_hsphy *hsphy; > + const struct override_param_map *cfg = of_device_get_match_data(dev); > + > + if (!cfg) > + return; > + > + hsphy = dev_get_drvdata(dev); > + > + for (i = 0; cfg[i].prop_name != NULL; i++) { > + ret = of_property_read_s32(node, cfg[i].prop_name, &val); > + if (ret) > + continue; > + > + qcom_snps_hsphy_override_param_update_val(cfg[i], val, > + &hsphy->update_seq_cfg[i]); > + dev_dbg(&hsphy->phy->dev, "Read param: %s dt_val: %d reg_val: 0x%x\n", > + cfg[i].prop_name, val, hsphy->update_seq_cfg[i].value); > + > + } > +} > + > static int qcom_snps_hsphy_probe(struct platform_device *pdev) > { > struct device *dev = &pdev->dev; > @@ -352,6 +602,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) > > dev_set_drvdata(dev, hsphy); > phy_set_drvdata(generic_phy, hsphy); > + qcom_snps_hsphy_read_override_param_seq(dev); > > phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); > if (!IS_ERR(phy_provider)) > -- > 2.7.4 >
diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c index 5d20378..2502294 100644 --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c @@ -52,6 +52,12 @@ #define USB2_SUSPEND_N BIT(2) #define USB2_SUSPEND_N_SEL BIT(3) +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0 (0x6c) +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1 (0x70) +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2 (0x74) +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3 (0x78) +#define PARAM_OVRD_MASK 0xFF + #define USB2_PHY_USB_PHY_CFG0 (0x94) #define UTMI_PHY_DATAPATH_CTRL_OVERRIDE_EN BIT(0) #define UTMI_PHY_CMN_CTRL_OVERRIDE_EN BIT(1) @@ -60,12 +66,47 @@ #define REFCLK_SEL_MASK GENMASK(1, 0) #define REFCLK_SEL_DEFAULT (0x2 << 0) +#define HS_DISCONNECT_MASK GENMASK(2, 0) +#define SQUELCH_DETECTOR_MASK GENMASK(7, 5) + +#define HS_AMPLITUDE_MASK GENMASK(3, 0) +#define PREEMPHASIS_DURATION_MASK BIT(5) +#define PREEMPHASIS_AMPLITUDE_MASK GENMASK(7, 6) + +#define HS_RISE_FALL_MASK GENMASK(1, 0) +#define HS_CROSSOVER_VOLTAGE_MASK GENMASK(3, 2) +#define HS_OUTPUT_IMPEDANCE_MASK GENMASK(5, 4) + +#define LS_FS_OUTPUT_IMPEDANCE_MASK GENMASK(3, 0) + static const char * const qcom_snps_hsphy_vreg_names[] = { "vdda-pll", "vdda33", "vdda18", }; #define SNPS_HS_NUM_VREGS ARRAY_SIZE(qcom_snps_hsphy_vreg_names) +struct override_param { + s32 value; + u8 reg_val; +}; + +struct override_param_map { + const char *prop_name; + const struct override_param *param_table; + u8 table_size; + u8 reg_offset; + u8 param_mask; +}; + +struct phy_override_seq { + bool need_update; + u8 offset; + u8 value; + u8 mask; +}; + +#define NUM_HSPHY_TUNING_PARAMS (9) + /** * struct qcom_snps_hsphy - snps hs phy attributes * @@ -91,6 +132,7 @@ struct qcom_snps_hsphy { bool phy_initialized; enum phy_mode mode; + struct phy_override_seq update_seq_cfg[NUM_HSPHY_TUNING_PARAMS]; }; static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, @@ -173,10 +215,158 @@ static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode, return 0; } +static const struct override_param hs_disconnect_sc7280[] = { + { -272, 0 }, + { 0, 1 }, + { 317, 2 }, + { 630, 3 }, + { 973, 4 }, + { 1332, 5 }, + { 1743, 6 }, + { 2156, 7 }, +}; + +static const struct override_param squelch_det_threshold_sc7280[] = { + { -2090, 7 }, + { -1560, 6 }, + { -1030, 5 }, + { -530, 4 }, + { 0, 3 }, + { 530, 2 }, + { 1060, 1 }, + { 1590, 0 }, +}; + +static const struct override_param hs_amplitude_sc7280[] = { + { -660, 0 }, + { -440, 1 }, + { -220, 2 }, + { 0, 3 }, + { 230, 4 }, + { 440, 5 }, + { 650, 6 }, + { 890, 7 }, + { 1110, 8 }, + { 1330, 9 }, + { 1560, 10 }, + { 1780, 11 }, + { 2000, 12 }, + { 2220, 13 }, + { 2430, 14 }, + { 2670, 15 }, +}; + +static const struct override_param preemphasis_duration_sc7280[] = { + { 10000, 1 }, + { 20000, 0 }, +}; + +static const struct override_param preemphasis_amplitude_sc7280[] = { + { 10000, 1 }, + { 20000, 2 }, + { 30000, 3 }, + { 40000, 0 }, +}; + +static const struct override_param hs_rise_fall_time_sc7280[] = { + { -4100, 3 }, + { 0, 2 }, + { 2810, 1 }, + { 5430, 0 }, +}; + +static const struct override_param hs_crossover_voltage_sc7280[] = { + { -31000, 1 }, + { 0, 3 }, + { 28000, 2 }, +}; + +static const struct override_param hs_output_impedance_sc7280[] = { + { -2300000, 3 }, + { 0, 2 }, + { 2600000, 1 }, + { 6100000, 0 }, +}; + +static const struct override_param ls_fs_output_impedance_sc7280[] = { + { -1053, 15 }, + { -557, 7 }, + { 0, 3 }, + { 612, 1 }, + { 1310, 0 }, +}; + +static const struct override_param_map sc7280_snps_7nm_phy[] = { + { + "qcom,hs-disconnect-bp", + hs_disconnect_sc7280, + ARRAY_SIZE(hs_disconnect_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0, + HS_DISCONNECT_MASK + }, + { + "qcom,squelch-detector-bp", + squelch_det_threshold_sc7280, + ARRAY_SIZE(squelch_det_threshold_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0, + SQUELCH_DETECTOR_MASK + }, + { + "qcom,hs-amplitude-bp", + hs_amplitude_sc7280, + ARRAY_SIZE(hs_amplitude_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1, + HS_AMPLITUDE_MASK + }, + { + "qcom,pre-emphasis-duration-bp", + preemphasis_duration_sc7280, + ARRAY_SIZE(preemphasis_duration_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1, + PREEMPHASIS_DURATION_MASK, + }, + { + "qcom,pre-emphasis-amplitude-bp", + preemphasis_amplitude_sc7280, + ARRAY_SIZE(preemphasis_amplitude_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1, + PREEMPHASIS_AMPLITUDE_MASK, + }, + { + "qcom,hs-rise-fall-time-bp", + hs_rise_fall_time_sc7280, + ARRAY_SIZE(hs_rise_fall_time_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2, + HS_RISE_FALL_MASK + }, + { + "qcom,hs-crossover-voltage-microvolt", + hs_crossover_voltage_sc7280, + ARRAY_SIZE(hs_crossover_voltage_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2, + HS_CROSSOVER_VOLTAGE_MASK + }, + { + "qcom,hs-output-impedance-micro-ohms", + hs_output_impedance_sc7280, + ARRAY_SIZE(hs_output_impedance_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2, + HS_OUTPUT_IMPEDANCE_MASK, + }, + { + "qcom,ls-fs-output-impedance-bp", + ls_fs_output_impedance_sc7280, + ARRAY_SIZE(ls_fs_output_impedance_sc7280), + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3, + LS_FS_OUTPUT_IMPEDANCE_MASK, + }, + {}, +}; + static int qcom_snps_hsphy_init(struct phy *phy) { struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy); - int ret; + int ret, i; dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__); @@ -223,6 +413,14 @@ static int qcom_snps_hsphy_init(struct phy *phy) qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1, VBUSVLDEXT0, VBUSVLDEXT0); + for (i = 0; i < ARRAY_SIZE(hsphy->update_seq_cfg); i++) { + if (hsphy->update_seq_cfg[i].need_update) + qcom_snps_hsphy_write_mask(hsphy->base, + hsphy->update_seq_cfg[i].offset, + hsphy->update_seq_cfg[i].mask, + hsphy->update_seq_cfg[i].value); + } + qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2, VREGBYPASS, VREGBYPASS); @@ -280,7 +478,10 @@ static const struct phy_ops qcom_snps_hsphy_gen_ops = { static const struct of_device_id qcom_snps_hsphy_of_match_table[] = { { .compatible = "qcom,sm8150-usb-hs-phy", }, { .compatible = "qcom,usb-snps-hs-5nm-phy", }, - { .compatible = "qcom,usb-snps-hs-7nm-phy", }, + { + .compatible = "qcom,usb-snps-hs-7nm-phy", + .data = &sc7280_snps_7nm_phy, + }, { .compatible = "qcom,usb-snps-femto-v2-phy", }, { } }; @@ -291,6 +492,55 @@ static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = { qcom_snps_hsphy_runtime_resume, NULL) }; +static void qcom_snps_hsphy_override_param_update_val( + const struct override_param_map map, + s32 dt_val, struct phy_override_seq *seq_entry) +{ + int i; + + /* + * Param table for each param is in increasing order + * of dt values. We need to iterate over the list to + * select the entry that matches the dt value and pick + * up the corresponding register value. + */ + for (i = 0; i < map.table_size - 1; i++) { + if (map.param_table[i].value == dt_val) + break; + } + + seq_entry->need_update = true; + seq_entry->offset = map.reg_offset; + seq_entry->mask = map.param_mask; + seq_entry->value = map.param_table[i].reg_val << __ffs(map.param_mask); +} + +static void qcom_snps_hsphy_read_override_param_seq(struct device *dev) +{ + struct device_node *node = dev->of_node; + s32 val; + int ret, i; + struct qcom_snps_hsphy *hsphy; + const struct override_param_map *cfg = of_device_get_match_data(dev); + + if (!cfg) + return; + + hsphy = dev_get_drvdata(dev); + + for (i = 0; cfg[i].prop_name != NULL; i++) { + ret = of_property_read_s32(node, cfg[i].prop_name, &val); + if (ret) + continue; + + qcom_snps_hsphy_override_param_update_val(cfg[i], val, + &hsphy->update_seq_cfg[i]); + dev_dbg(&hsphy->phy->dev, "Read param: %s dt_val: %d reg_val: 0x%x\n", + cfg[i].prop_name, val, hsphy->update_seq_cfg[i].value); + + } +} + static int qcom_snps_hsphy_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -352,6 +602,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) dev_set_drvdata(dev, hsphy); phy_set_drvdata(generic_phy, hsphy); + qcom_snps_hsphy_read_override_param_seq(dev); phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); if (!IS_ERR(phy_provider))
Add support for overriding electrical signal tuning parameters for SNPS HS Phy. Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> --- drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 255 +++++++++++++++++++++++++- 1 file changed, 253 insertions(+), 2 deletions(-)