@@ -33,6 +33,15 @@ config PHY_MVEBU_A3700_COMPHY
shared serdes PHYs on Marvell Armada 3700. Its serdes lanes can be
used by various controllers: Ethernet, SATA, USB3, PCIe.
+config PHY_MVEBU_A3700_UTMI
+ tristate "Marvell A3700 UTMI driver"
+ depends on ARCH_MVEBU || COMPILE_TEST
+ depends on OF
+ default y
+ select GENERIC_PHY
+ help
+ Enable this to support Marvell A3700 UTMI PHY driver.
+
config PHY_MVEBU_CP110_COMPHY
tristate "Marvell CP110 comphy driver"
depends on ARCH_MVEBU || COMPILE_TEST
@@ -3,6 +3,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY) += phy-armada375-usb2.o
obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o
obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o
obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY) += phy-mvebu-a3700-comphy.o
+obj-$(CONFIG_PHY_MVEBU_A3700_UTMI) += phy-mvebu-a3700-utmi.o
obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY) += phy-mvebu-cp110-comphy.o
obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
obj-$(CONFIG_PHY_PXA_28NM_HSIC) += phy-pxa-28nm-hsic.o
new file mode 100644
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell
+ *
+ * Authors:
+ * Igal Liberman <igall@marvell.com>
+ * Miquèl Raynal <miquel.raynal@bootlin.com>
+ *
+ * Marvell A3700 UTMI PHY driver
+ */
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* Armada 3700 UTMI PHY registers */
+#define USB2_PHY_PLL_CTRL_REG0 0x0
+#define PLL_REF_DIV_OFF 0
+#define PLL_REF_DIV_MASK GENMASK(6, 0)
+#define PLL_REF_DIV_5 5
+#define PLL_FB_DIV_OFF 16
+#define PLL_FB_DIV_MASK GENMASK(24, 16)
+#define PLL_FB_DIV_96 96
+#define PLL_SEL_LPFR_OFF 28
+#define PLL_SEL_LPFR_MASK GENMASK(29, 28)
+#define PLL_READY BIT(31)
+#define USB2_PHY_CAL_CTRL 0x8
+#define PHY_PLLCAL_DONE BIT(31)
+#define PHY_IMPCAL_DONE BIT(23)
+#define USB2_RX_CHAN_CTRL1 0x18
+#define USB2PHY_SQCAL_DONE BIT(31)
+#define USB2_PHY_OTG_CTRL 0x34
+#define PHY_PU_OTG BIT(4)
+#define USB2_PHY_CHRGR_DETECT 0x38
+#define PHY_CDP_EN BIT(2)
+#define PHY_DCP_EN BIT(3)
+#define PHY_PD_EN BIT(4)
+#define PHY_PU_CHRG_DTC BIT(5)
+#define PHY_CDP_DM_AUTO BIT(7)
+#define PHY_ENSWITCH_DP BIT(12)
+#define PHY_ENSWITCH_DM BIT(13)
+
+/* Armada 3700 USB miscellaneous registers */
+#define USB2_PHY_CTRL(usb32) (usb32 ? 0x20 : 0x4)
+#define RB_USB2PHY_PU BIT(0)
+#define USB2_DP_PULLDN_DEV_MODE BIT(5)
+#define USB2_DM_PULLDN_DEV_MODE BIT(6)
+#define RB_USB2PHY_SUSPM(usb32) (usb32 ? BIT(14) : BIT(7))
+
+#define PLL_LOCK_DELAY_US 10000
+#define PLL_LOCK_TIMEOUT_US 1000000
+
+/**
+ * struct mvebu_a3700_utmi_caps - PHY capabilities
+ *
+ * @usb32: Flag indicating which PHY is in use (impacts the register map):
+ * - The UTMI PHY wired to the USB3/USB2 controller (otg)
+ * - The UTMI PHY wired to the USB2 controller (host only)
+ * @ops: PHY operations
+ */
+struct mvebu_a3700_utmi_caps {
+ int usb32;
+ const struct phy_ops *ops;
+};
+
+/**
+ * struct mvebu_a3700_utmi - PHY driver data
+ *
+ * @regs: PHY registers
+ * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
+ * @caps: PHY capabilities
+ * @phy: PHY handle
+ */
+struct mvebu_a3700_utmi {
+ void __iomem *regs;
+ struct regmap *usb_misc;
+ const struct mvebu_a3700_utmi_caps *caps;
+ struct phy *phy;
+};
+
+static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
+{
+ struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
+ struct device *dev = &phy->dev;
+ int usb32 = utmi->caps->usb32;
+ int ret = 0;
+ u32 reg;
+
+ /*
+ * Setup PLL. 40MHz clock used to be the default, being 25MHz now.
+ * See "PLL Settings for Typical REFCLK" table.
+ */
+ reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
+ reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
+ reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF) |
+ (PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
+ writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
+
+ /* Enable PHY pull up and disable USB2 suspend */
+ regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
+ RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
+ RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
+
+ if (usb32) {
+ /* Power up OTG module */
+ reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
+ reg |= PHY_PU_OTG;
+ writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
+
+ /* Disable PHY charger detection */
+ reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
+ reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
+ PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
+ writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
+
+ /* Disable PHY DP/DM pull-down (used for device mode) */
+ regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
+ USB2_DP_PULLDN_DEV_MODE |
+ USB2_DM_PULLDN_DEV_MODE, 0);
+ }
+
+ /* Wait for PLL calibration */
+ ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
+ reg & PHY_PLLCAL_DONE,
+ PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+ if (ret) {
+ dev_err(dev, "Failed to end USB2 PLL calibration\n");
+ return ret;
+ }
+
+ /* Wait for impedance calibration */
+ ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
+ reg & PHY_IMPCAL_DONE,
+ PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+ if (ret) {
+ dev_err(dev, "Failed to end USB2 impedance calibration\n");
+ return ret;
+ }
+
+ /* Wait for squelch calibration */
+ ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
+ reg & USB2PHY_SQCAL_DONE,
+ PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+ if (ret) {
+ dev_err(dev, "Failed to end USB2 unknown calibration\n");
+ return ret;
+ }
+
+ /* Wait for PLL to be locked */
+ ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
+ reg & PLL_READY,
+ PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+ if (ret)
+ dev_err(dev, "Failed to lock USB2 PLL\n");
+
+ return ret;
+}
+
+static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
+{
+ struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
+ int usb32 = utmi->caps->usb32;
+ u32 reg;
+
+ /* Disable PHY pull-up and enable USB2 suspend */
+ reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
+ reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
+ writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
+
+ /* Power down OTG module */
+ if (usb32) {
+ reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
+ reg &= ~PHY_PU_OTG;
+ writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
+ }
+
+ return 0;
+}
+
+static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
+ .power_on = mvebu_a3700_utmi_phy_power_on,
+ .power_off = mvebu_a3700_utmi_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
+ .usb32 = true,
+ .ops = &mvebu_a3700_utmi_phy_ops,
+};
+
+static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
+ .usb32 = false,
+ .ops = &mvebu_a3700_utmi_phy_ops,
+};
+
+static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
+ {
+ .compatible = "marvell,a3700-utmi-otg-phy",
+ .data = &mvebu_a3700_utmi_otg_phy_caps,
+ },
+ {
+ .compatible = "marvell,a3700-utmi-host-phy",
+ .data = &mvebu_a3700_utmi_host_phy_caps,
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
+
+static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct mvebu_a3700_utmi *utmi;
+ struct phy_provider *provider;
+ struct resource *res;
+
+ utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
+ if (!utmi)
+ return -ENOMEM;
+
+ /* Get UTMI memory region */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(dev, "Missing UTMI PHY memory resource\n");
+ return -ENODEV;
+ }
+
+ utmi->regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(utmi->regs))
+ return PTR_ERR(utmi->regs);
+
+ /* Get miscellaneous Host/PHY region */
+ utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "marvell,usb-misc-reg");
+ if (IS_ERR(utmi->usb_misc)) {
+ dev_err(dev,
+ "Missing USB misc purpose system controller\n");
+ return PTR_ERR(utmi->usb_misc);
+ }
+
+ /* Retrieve PHY capabilities */
+ utmi->caps = of_device_get_match_data(dev);
+
+ /* Instantiate the PHY */
+ utmi->phy = devm_phy_create(dev, NULL, utmi->caps->ops);
+ if (IS_ERR(utmi->phy)) {
+ dev_err(dev, "Failed to create the UTMI PHY\n");
+ return PTR_ERR(utmi->phy);
+ }
+
+ phy_set_drvdata(utmi->phy, utmi);
+
+ /* Ensure the PHY is powered off */
+ utmi->caps->ops->power_off(utmi->phy);
+
+ provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(provider);
+}
+
+static struct platform_driver mvebu_a3700_utmi_driver = {
+ .probe = mvebu_a3700_utmi_phy_probe,
+ .driver = {
+ .name = "mvebu-a3700-utmi-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = mvebu_a3700_utmi_of_match,
+ },
+};
+module_platform_driver(mvebu_a3700_utmi_driver);
+
+MODULE_AUTHOR("Igal Liberman <igall@marvell.com>");
+MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
+MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
+MODULE_LICENSE("GPL v2");