@@ -66,9 +66,7 @@ int hcd_buffer_create(struct usb_hcd *hcd)
char name[16];
int i, size;
- if (hcd->localmem_pool ||
- !IS_ENABLED(CONFIG_HAS_DMA) ||
- !is_device_dma_capable(hcd->self.sysdev))
+ if (hcd->localmem_pool || !hcd_uses_dma(hcd))
return 0;
for (i = 0; i < HCD_BUFFER_POOLS; i++) {
@@ -129,8 +127,7 @@ void *hcd_buffer_alloc(
return gen_pool_dma_alloc(hcd->localmem_pool, size, dma);
/* some USB hosts just use PIO */
- if (!IS_ENABLED(CONFIG_HAS_DMA) ||
- !is_device_dma_capable(bus->sysdev)) {
+ if (!hcd_uses_dma(hcd)) {
*dma = ~(dma_addr_t) 0;
return kmalloc(size, mem_flags);
}
@@ -160,8 +157,7 @@ void hcd_buffer_free(
return;
}
- if (!IS_ENABLED(CONFIG_HAS_DMA) ||
- !is_device_dma_capable(bus->sysdev)) {
+ if (!hcd_uses_dma(hcd)) {
kfree(addr);
return;
}
@@ -1412,7 +1412,7 @@ int usb_hcd_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb,
if (usb_endpoint_xfer_control(&urb->ep->desc)) {
if (hcd->self.uses_pio_for_control)
return ret;
- if (IS_ENABLED(CONFIG_HAS_DMA) && hcd->self.uses_dma) {
+ if (hcd_uses_dma(hcd)) {
if (is_vmalloc_addr(urb->setup_packet)) {
WARN_ONCE(1, "setup packet is not dma capable\n");
return -EAGAIN;
@@ -1446,7 +1446,7 @@ int usb_hcd_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb,
dir = usb_urb_dir_in(urb) ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
if (urb->transfer_buffer_length != 0
&& !(urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP)) {
- if (IS_ENABLED(CONFIG_HAS_DMA) && hcd->self.uses_dma) {
+ if (hcd_uses_dma(hcd)) {
if (urb->num_sgs) {
int n;
@@ -4608,7 +4608,7 @@ static int _dwc2_hcd_urb_enqueue(struct usb_hcd *hcd, struct urb *urb,
buf = urb->transfer_buffer;
- if (hcd->self.uses_dma) {
+ if (hcd_uses_dma(hcd)) {
if (!buf && (urb->transfer_dma & 3)) {
dev_err(hsotg->dev,
"%s: unaligned transfer with no transfer_buffer",
@@ -1457,7 +1457,7 @@ typedef void (*usb_complete_t)(struct urb *);
* field rather than determining a dma address themselves.
*
* Note that transfer_buffer must still be set if the controller
- * does not support DMA (as indicated by bus.uses_dma) and when talking
+ * does not support DMA (as indicated by hcd_uses_dma()) and when talking
* to root hub. If you have to trasfer between highmem zone and the device
* on such controller, create a bounce buffer or bail out with an error.
* If transfer_buffer cannot be set (is in highmem) and the controller is DMA
@@ -422,6 +422,9 @@ static inline bool hcd_periodic_completion_in_progress(struct usb_hcd *hcd,
return hcd->high_prio_bh.completing_ep == ep;
}
+#define hcd_uses_dma(hcd) \
+ (IS_ENABLED(CONFIG_HAS_DMA) && (hcd)->self.uses_dma)
+
extern int usb_hcd_link_urb_to_ep(struct usb_hcd *hcd, struct urb *urb);
extern int usb_hcd_check_unlink_urb(struct usb_hcd *hcd, struct urb *urb,
int status);
The USB buffer allocation code is the only place in the usb core (and in fact the whole kernel) that uses is_device_dma_capable, while the URB mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer allocation to use the uses_dma flag used by the rest of the USB code, and create a helper in hcd.h that checks this flag as well as the CONFIG_HAS_DMA to simplify the caller a bit. Signed-off-by: Christoph Hellwig <hch@lst.de> --- drivers/usb/core/buffer.c | 10 +++------- drivers/usb/core/hcd.c | 4 ++-- drivers/usb/dwc2/hcd.c | 2 +- include/linux/usb.h | 2 +- include/linux/usb/hcd.h | 3 +++ 5 files changed, 10 insertions(+), 11 deletions(-)