@@ -37,6 +37,7 @@ Required properties:
- Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
- Tegra210: "nvidia,tegra210-xusb-padctl"
- Tegra186: "nvidia,tegra186-xusb-padctl"
+ - Tegra194: "nvidia,tegra194-xusb-padctl"
- reg: Physical base address and length of the controller's registers.
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must include the following entries:
@@ -62,6 +63,10 @@ For Tegra186:
- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
+For Tegra194:
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+ 3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
Pad nodes:
==========
@@ -154,6 +159,11 @@ For Tegra210, the list of valid PHY nodes is given below:
- sata: sata-0
- functions: "usb3-ss", "sata"
+For Tegra194, the list of valid PHY nodes is given below:
+- usb2: usb2-0, usb2-1, usb2-2, usb2-3
+ - functions: "xusb"
+- usb3: usb3-0, usb3-1, usb3-2, usb3-3
+ - functions: "xusb"
Port nodes:
===========
@@ -221,6 +231,9 @@ Optional properties:
is internal. In the absence of this property the port is considered to be
external.
+- nvidia,disable-gen2: A boolean property whose presence determines that a port
+ should be limited to USB 3.1 Gen 1. This property is only for Tegra194.
+
For Tegra124 and Tegra132, the XUSB pad controller exposes the following
ports:
- 3x USB2: usb2-0, usb2-1, usb2-2
@@ -233,6 +246,9 @@ For Tegra210, the XUSB pad controller exposes the following ports:
- 2x HSIC: hsic-0, hsic-1
- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
+For Tegra194, the XUSB pad controller exposes the following ports:
+- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
+- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
Examples:
=========
Extend the bindings to cover the set of features found in Tegra194. Note that, technically, there are four more supplies connected to the XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL) , but the power sequencing requirements of Tegra194 require these to be under the control of the PMIC. Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it is possible for some platforms have long signal trace that could not provide sufficient electrical environment for Gen 2 speed. To deal with this, a new device node property "nvidia,disable-gen2" was added to Tegra194 that be used to specifically disable Gen 2 speed for a particular USB 3.0 port so that the port can be limited to Gen 1 speed and avoid the instability. Signed-off-by: JC Kuo <jckuo@nvidia.com> --- Changes in v3: none Changes in v2: - fix a typo .../bindings/phy/nvidia,tegra124-xusb-padctl.txt | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)