@@ -1297,7 +1297,23 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
wIndex, link_state);
goto error;
}
+
+ if (link_state == USB_SS_PORT_LS_U0) {
+ if ((temp & PORT_PLS_MASK) == XDEV_U0)
+ break;
+
+ reinit_completion(&bus_state->link_change_done[wIndex]);
+ xhci_set_link_state(xhci, ports[wIndex], USB_SS_PORT_LS_U0);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ if (!wait_for_completion_timeout(&bus_state->link_change_done[wIndex], msecs_to_jiffies(100)))
+ xhci_dbg(xhci, "missing U0 port change event for port %d-%d\n", hcd->self.busnum, wIndex + 1);
+ spin_lock_irqsave(&xhci->lock, flags);
+ temp = readl(ports[wIndex]->addr);
+ break;
+ }
+
if (link_state == USB_SS_PORT_LS_U3) {
+ int retries = 10;
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (slot_id) {
@@ -1308,26 +1324,18 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
}
- }
-
- xhci_set_link_state(xhci, ports[wIndex], link_state);
-
- spin_unlock_irqrestore(&xhci->lock, flags);
- if (link_state == USB_SS_PORT_LS_U3) {
- int retries = 10;
-
+ xhci_set_link_state(xhci, ports[wIndex], USB_SS_PORT_LS_U3);
+ spin_unlock_irqrestore(&xhci->lock, flags);
while (retries--) {
msleep(10); /* wait device to enter */
temp = readl(ports[wIndex]->addr);
if ((temp & PORT_PLS_MASK) == XDEV_U3)
break;
}
- }
- spin_lock_irqsave(&xhci->lock, flags);
-
- temp = readl(ports[wIndex]->addr);
- if (link_state == USB_SS_PORT_LS_U3)
+ spin_lock_irqsave(&xhci->lock, flags);
+ temp = readl(ports[wIndex]->addr);
bus_state->suspended_ports |= 1 << wIndex;
+ }
break;
case USB_PORT_FEAT_POWER:
/*
@@ -2531,6 +2531,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
xhci->usb3_rhub.bus_state.resume_done[i] = 0;
/* Only the USB 2.0 completions will ever be used. */
init_completion(&xhci->usb2_rhub.bus_state.rexit_done[i]);
+ init_completion(&xhci->usb2_rhub.bus_state.link_change_done[i]);
+ init_completion(&xhci->usb3_rhub.bus_state.link_change_done[i]);
}
if (scratchpad_alloc(xhci, flags))
@@ -1677,6 +1677,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
(portsc & PORT_PLS_MASK) == XDEV_U1 ||
(portsc & PORT_PLS_MASK) == XDEV_U2)) {
xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
+ complete(&bus_state->link_change_done[hcd_portnum]);
/* We've just brought the device into U0/1/2 through either the
* Resume state after a device remote wakeup, or through the
* U3Exit state after a host-initiated resume. If it's a device
@@ -1694,6 +1694,7 @@ struct xhci_bus_state {
/* Which ports are waiting on RExit to U0 transition. */
unsigned long rexit_ports;
struct completion rexit_done[USB_MAXCHILDREN];
+ struct completion link_change_done[USB_MAXCHILDREN];
};
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition time. The 20ms is not enough for some devices. Intead of polling PLS or PLC, we can facilitate the port change event to know that the link transits to U0 is completed. While at it, seperate U0 and U3 case Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> --- drivers/usb/host/xhci-hub.c | 34 +++++++++++++++++++++------------- drivers/usb/host/xhci-mem.c | 2 ++ drivers/usb/host/xhci-ring.c | 1 + drivers/usb/host/xhci.h | 1 + 4 files changed, 25 insertions(+), 13 deletions(-)