@@ -11356,6 +11356,13 @@ S: Maintained
F: Documentation/devicetree/bindings/usb/usb251xb.txt
F: drivers/usb/misc/usb251xb.c
+MICROCHIP USB253X DRIVER
+M: Christian Eggers <ceggers@arri.de>
+L: linux-usb@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/usb/usb253x.yaml
+F: drivers/usb/misc/usb253x.c
+
MICROCHIP USBA UDC DRIVER
M: Cristian Birsan <cristian.birsan@microchip.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -242,6 +242,16 @@ config USB_HUB_USB251XB
parameters may be set in devicetree or platform data.
Say Y or M here if you need to configure such a device via SMBus.
+config USB_HUB_USB253X
+ tristate "USB253X Hub Controller Configuration Driver"
+ depends on I2C
+ select REGMAP
+ help
+ This option enables support for configuration via I2C bus of the
+ Microchip USB253x/xi USB 2.0 Hub Controller series.
+ Configuration parameters may be set in devicetree or platform data.
+ Say Y or M here if you need to configure such a device via I2C.
+
config USB_HSIC_USB3503
tristate "USB3503 HSIC to USB20 Driver"
depends on I2C
@@ -25,6 +25,7 @@ obj-$(CONFIG_USB_USS720) += uss720.o
obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o
obj-$(CONFIG_USB_YUREX) += yurex.o
obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o
+obj-$(CONFIG_USB_HUB_USB253X) += usb253x.o
obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o
obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o
obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o
new file mode 100644
@@ -0,0 +1,834 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for Microchip USB253x USB 2.0 Hi-Speed Hub Controller
+ * Configuration via I2C.
+ *
+ * Copyright (c) 2020 ARRI Lighting
+ *
+ * This work is based on the USB251xb driver by Richard Leitner.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/nls.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+/* Internal Register Set Addresses acc. to DS00001801C */
+#define USB253X_ADDR_VENDOR_ID 0x3000
+#define USB253X_ADDR_PRODUCT_ID 0x3002
+#define USB253X_ADDR_DEVICE_ID 0x3004
+#define USB253X_ADDR_HUB_CFG 0x3006
+#define USB253X_HUB_CFG3_PRTMAP_EN BIT(3)
+#define USB253X_HUB_CFG3_STRING_EN BIT(0)
+#define USB253X_ADDR_NON_REMOVABLE_DEVICES 0x3009
+#define USB253X_ADDR_PORT_DISABLE_SELF 0x300A
+#define USB253X_ADDR_PORT_DISABLE_BUS 0x300B
+#define USB253X_ADDR_POWER_ON_TIME 0x3010
+#define USB253X_ADDR_LANGUAGE_ID 0x3011
+#define USB253X_ADDR_MANUFACTURER_STRING_LEN 0x3013
+#define USB253X_ADDR_PRODUCT_STRING_LEN 0x3014
+#define USB253X_ADDR_SERIAL_STRING_LEN 0x3015
+#define USB253X_ADDR_STRINGS 0x3016
+#define USB253X_STRINGS_BUFSIZE 93 /* chars (UTF16) */
+#define USB253X_ADDR_HUB_CTRL_REMAP 0x30FD
+#define USB253X_ADDR_USB2_HUB_CTRL 0x3104
+#define USB253X_USB2_HUB_CTRL_LPM_DISABLE BIT(1)
+#define USB253X_ADDR_INTERNAL_PORT 0x4130
+#define USB253X_INTERNAL_PORT_PORT_ENUM_DEFAULT 0b00
+#define USB253X_INTERNAL_PORT_PORT_ENUM_ALWAYS_ENABLE 0b01
+#define USB253X_INTERNAL_PORT_PORT_ENUM_ALWAYS_DISABLE 0b10
+
+#define DRIVER_NAME "usb253x"
+
+
+struct usb253x {
+ struct device *dev;
+ struct i2c_client *i2c;
+ struct regulator *vdd;
+ struct regmap *regmap;
+ u8 skip_config;
+ struct gpio_desc *gpio_reset;
+};
+
+#ifdef CONFIG_GPIOLIB
+static int usb253x_check_dev_children(struct device *dev, void *child)
+{
+ if (dev->type == &i2c_adapter_type) {
+ return device_for_each_child(dev, child,
+ usb253x_check_dev_children);
+ }
+
+ return (dev == child);
+}
+
+static int usb253x_check_gpio_chip(struct usb253x *hub)
+{
+ struct gpio_chip *gc = gpiod_to_chip(hub->gpio_reset);
+ struct i2c_adapter *adap = hub->i2c->adapter;
+ int ret;
+
+ if (!hub->gpio_reset)
+ return 0;
+
+ if (!gc)
+ return -EINVAL;
+
+ ret = usb253x_check_dev_children(&adap->dev, gc->parent);
+ if (ret) {
+ dev_err(hub->dev, "Reset GPIO chip is at the same i2c-bus\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+#else
+static int usb253x_check_gpio_chip(struct usb253x *hub)
+{
+ return 0;
+}
+#endif
+
+static void usb253x_reset(struct usb253x *hub, int state)
+{
+ if (state) {
+ /* During rising edge of reset, there must be no traffic on the i2c bus */
+ i2c_lock_bus(hub->i2c->adapter, I2C_LOCK_SEGMENT);
+ gpiod_set_value_cansleep(hub->gpio_reset, 1);
+ /* Wait for i2c logic to come up (hub seems to require ~210 ms if
+ * RESET_N pulse was longer than 25 ms)
+ */
+ msleep(250);
+ i2c_unlock_bus(hub->i2c->adapter, I2C_LOCK_SEGMENT);
+ } else {
+ gpiod_set_value_cansleep(hub->gpio_reset, 0);
+ /* minimum reset pulse width from data sheet is 5 us */
+ usleep_range(5, 10);
+ }
+}
+
+static void usb253x_get_ports_field(struct usb253x *hub,
+ const char *prop_name, u8 port_cnt,
+ u8 *fld)
+{
+ struct device *dev = hub->dev;
+ struct property *prop;
+ const __be32 *p;
+ u32 port;
+
+ of_property_for_each_u32(dev->of_node, prop_name, prop, p, port) {
+ if ((port >= 1) && (port <= port_cnt))
+ *fld |= BIT(port);
+ else
+ dev_warn(dev, "port %u doesn't exist\n", port);
+ }
+}
+
+static int usb253x_connect(struct usb253x *hub)
+{
+ struct device *dev = hub->dev;
+ struct device_node *np = dev->of_node;
+ int err;
+ char attach_buffer[3];
+
+ usb253x_reset(hub, 1);
+
+ if (hub->skip_config) {
+ dev_info(dev, "Skip hub configuration, only attach.\n");
+ } else {
+ u16 vendor_id, product_id, device_id, lang_id;
+ u8 hub_cfg[3];
+ u32 property_u32;
+ char const *manufacturer;
+ char const *product;
+ char const *serial;
+ u8 non_rem_dev = 0;
+ u8 port_disable_sp = 0;
+ u8 port_disable_bp = 0;
+ wchar_t strings[USB253X_STRINGS_BUFSIZE];
+ int strings_used = 0;
+ u32 hub_controller_port = 0;
+
+ memset(strings, 0, sizeof(strings));
+
+ if (!of_property_read_u16_array(np, "vendor-id", &vendor_id, 1)) {
+ char buffer[] = { vendor_id >> 8, vendor_id };
+
+ err = regmap_bulk_write(hub->regmap, USB253X_ADDR_VENDOR_ID,
+ buffer, ARRAY_SIZE(buffer));
+ if (err) {
+ dev_err(dev, "Setting vendor id failed: %d\n", err);
+ return err;
+ }
+ }
+
+ if (!of_property_read_u16_array(np, "product-id", &product_id, 1)) {
+ char buffer[] = { product_id >> 8, product_id };
+
+ err = regmap_bulk_write(hub->regmap, USB253X_ADDR_PRODUCT_ID,
+ buffer, ARRAY_SIZE(buffer));
+ if (err) {
+ dev_err(dev, "Setting product id failed: %d\n", err);
+ return err;
+ }
+ }
+
+ if (!of_property_read_u16_array(np, "device-id", &device_id, 1)) {
+ char buffer[] = { device_id >> 8, device_id };
+
+ err = regmap_bulk_write(hub->regmap, USB253X_ADDR_DEVICE_ID,
+ buffer, ARRAY_SIZE(buffer));
+ if (err) {
+ dev_err(dev, "Setting device id failed: %d\n", err);
+ return err;
+ }
+ }
+
+ err = regmap_bulk_read(hub->regmap, USB253X_ADDR_HUB_CFG,
+ hub_cfg, ARRAY_SIZE(hub_cfg));
+ if (err) {
+ dev_err(dev, "Reading hub cfg failed: %d\n", err);
+ return err;
+ }
+
+ if (of_get_property(np, "self-powered", NULL)) {
+ hub_cfg[0] |= BIT(7);
+
+ /* Configure Over-Current sens when self-powered */
+ hub_cfg[0] &= ~BIT(2);
+ if (of_get_property(np, "ganged-sensing", NULL))
+ hub_cfg[0] &= ~BIT(1);
+ else if (of_get_property(np, "individual-sensing", NULL))
+ hub_cfg[0] |= BIT(1);
+ } else if (of_get_property(np, "bus-powered", NULL)) {
+ hub_cfg[0] &= ~BIT(7);
+
+ /* Disable Over-Current sense when bus-powered */
+ hub_cfg[0] |= BIT(2);
+ }
+
+ if (of_get_property(np, "disable-hi-speed", NULL))
+ hub_cfg[0] |= BIT(5);
+
+ if (of_get_property(np, "multi-tt", NULL))
+ hub_cfg[0] |= BIT(4);
+ else if (of_get_property(np, "single-tt", NULL))
+ hub_cfg[0] &= ~BIT(4);
+
+ if (of_get_property(np, "disable-eop", NULL))
+ hub_cfg[0] |= BIT(3);
+
+ if (of_get_property(np, "individual-port-switching", NULL))
+ hub_cfg[0] |= BIT(0);
+ else if (of_get_property(np, "ganged-port-switching", NULL))
+ hub_cfg[0] &= ~BIT(0);
+
+ if (of_get_property(np, "dynamic-power-switching", NULL))
+ hub_cfg[1] |= BIT(7);
+
+ if (!of_property_read_u32(np, "oc-delay-us", &property_u32)) {
+ if (property_u32 == 100) {
+ /* 100 us*/
+ hub_cfg[1] &= ~BIT(5);
+ hub_cfg[1] &= ~BIT(4);
+ } else if (property_u32 == 4000) {
+ /* 4 ms */
+ hub_cfg[1] &= ~BIT(5);
+ hub_cfg[1] |= BIT(4);
+ } else if (property_u32 == 16000) {
+ /* 16 ms */
+ hub_cfg[1] |= BIT(5);
+ hub_cfg[1] |= BIT(4);
+ } else {
+ /* 8 ms (DEFAULT) */
+ hub_cfg[1] |= BIT(5);
+ hub_cfg[1] &= ~BIT(4);
+ }
+ }
+
+ if (of_get_property(np, "compound-device", NULL))
+ hub_cfg[1] |= BIT(3);
+
+ if (of_get_property(np, "port-mapping-mode", NULL))
+ hub_cfg[2] |= USB253X_HUB_CFG3_PRTMAP_EN;
+
+ /* hub controller will only work when port mapping is enabled and
+ * controller port is mapped
+ */
+ if (!of_property_read_u32(np, "hub-controller-port",
+ &hub_controller_port))
+ hub_cfg[2] |= USB253X_HUB_CFG3_PRTMAP_EN;
+
+ /* port mapping requires that Link Power Management is disabled */
+ if (hub_cfg[2] & USB253X_HUB_CFG3_PRTMAP_EN) {
+ unsigned int usb2_hub_ctrl;
+
+ /* Disable Link Power Management */
+ err = regmap_read(hub->regmap, USB253X_ADDR_USB2_HUB_CTRL,
+ &usb2_hub_ctrl);
+ if (err) {
+ dev_err(dev, "Reading USB2 Hub Control failed: %d\n", err);
+ return err;
+ }
+
+ usb2_hub_ctrl |= USB253X_USB2_HUB_CTRL_LPM_DISABLE;
+
+ err = regmap_write(hub->regmap, USB253X_ADDR_USB2_HUB_CTRL,
+ usb2_hub_ctrl);
+ if (err) {
+ dev_err(dev, "Writing USB2 Hub Control failed: %d\n", err);
+ return err;
+ }
+ }
+
+ manufacturer = of_get_property(np, "manufacturer", NULL);
+ product = of_get_property(np, "product", NULL);
+ serial = of_get_property(np, "serial", NULL);
+
+ if (manufacturer || product || serial)
+ hub_cfg[2] |= USB253X_HUB_CFG3_STRING_EN;
+
+ err = regmap_bulk_write(hub->regmap, USB253X_ADDR_HUB_CFG,
+ hub_cfg, ARRAY_SIZE(hub_cfg));
+ if (err) {
+ dev_err(dev, "Setting hub cfg failed: %d\n", err);
+ return err;
+ }
+
+ usb253x_get_ports_field(hub, "non-removable-ports", 4, &non_rem_dev);
+ err = regmap_write(hub->regmap, USB253X_ADDR_NON_REMOVABLE_DEVICES,
+ non_rem_dev);
+ if (err) {
+ dev_err(dev, "Setting non removable devices failed: %d\n", err);
+ return err;
+ }
+
+ usb253x_get_ports_field(hub, "sp-disabled-ports", 4, &port_disable_sp);
+ err = regmap_write(hub->regmap, USB253X_ADDR_PORT_DISABLE_SELF,
+ port_disable_sp);
+ if (err) {
+ dev_err(dev, "Setting port disable self powered failed: %d\n", err);
+ return err;
+ }
+
+ usb253x_get_ports_field(hub, "bp-disabled-ports", 4, &port_disable_bp);
+ err = regmap_write(hub->regmap, USB253X_ADDR_PORT_DISABLE_BUS,
+ port_disable_bp);
+ if (err) {
+ dev_err(dev, "Setting port disable powered powered failed: %d\n", err);
+ return err;
+ }
+
+ if (!of_property_read_u32(np, "power-on-time-ms", &property_u32)) {
+ u8 power_on_time = min_t(u8, property_u32 / 2, 255);
+
+ err = regmap_write(hub->regmap, USB253X_ADDR_POWER_ON_TIME,
+ power_on_time);
+ if (err) {
+ dev_err(dev, "Setting port disable powered powered failed: %d\n",
+ err);
+ return err;
+ }
+ }
+
+ if (!of_property_read_u16_array(np, "language-id", &lang_id, 1)) {
+ char buffer[] = { lang_id >> 8, lang_id };
+
+ err = regmap_bulk_write(hub->regmap, USB253X_ADDR_LANGUAGE_ID,
+ buffer, ARRAY_SIZE(buffer));
+ if (err) {
+ dev_err(dev, "Setting language id failed: %d\n", err);
+ return err;
+ }
+ }
+
+ if (manufacturer) {
+ u8 manufacturer_len = utf8s_to_utf16s(manufacturer, strlen(manufacturer),
+ UTF16_LITTLE_ENDIAN,
+ &strings[strings_used],
+ USB253X_STRINGS_BUFSIZE - strings_used);
+
+ err = regmap_write(hub->regmap, USB253X_ADDR_MANUFACTURER_STRING_LEN,
+ manufacturer_len);
+ if (err) {
+ dev_err(dev, "Setting manufacturer string length failed: %d\n",
+ err);
+ return err;
+ }
+
+ strings_used += manufacturer_len;
+ }
+
+ if (product) {
+ u8 product_len = utf8s_to_utf16s(product, strlen(product),
+ UTF16_LITTLE_ENDIAN,
+ &strings[strings_used],
+ USB253X_STRINGS_BUFSIZE - strings_used);
+
+ err = regmap_write(hub->regmap, USB253X_ADDR_PRODUCT_STRING_LEN,
+ product_len);
+ if (err) {
+ dev_err(dev, "Setting product string length failed: %d\n", err);
+ return err;
+ }
+
+ strings_used += product_len;
+ }
+
+ if (serial) {
+ u8 serial_len = utf8s_to_utf16s(serial, strlen(serial),
+ UTF16_LITTLE_ENDIAN,
+ &strings[strings_used],
+ USB253X_STRINGS_BUFSIZE - strings_used);
+
+ err = regmap_write(hub->regmap, USB253X_ADDR_SERIAL_STRING_LEN,
+ serial_len);
+ if (err) {
+ dev_err(dev, "Setting serial string length failed: %d\n", err);
+ return err;
+ }
+
+ strings_used += serial_len;
+ }
+
+ err = regmap_bulk_write(hub->regmap, USB253X_ADDR_STRINGS,
+ strings, sizeof(strings));
+ if (err) {
+ dev_err(dev, "Setting strings failed: %d\n", err);
+ return err;
+ }
+
+ if (hub_controller_port != 0) {
+ /* Writes to this register are disabled unless PRTMAP_EN bit in
+ * HUB_CFG_3 is set.
+ */
+ err = regmap_write(hub->regmap, USB253X_ADDR_HUB_CTRL_REMAP,
+ hub_controller_port);
+ if (err) {
+ dev_err(dev, "Setting hub controller remap failed: %d\n", err);
+ return err;
+ }
+
+ err = regmap_write(hub->regmap, USB253X_ADDR_INTERNAL_PORT,
+ USB253X_INTERNAL_PORT_PORT_ENUM_ALWAYS_ENABLE);
+ if (err) {
+ dev_err(dev, "Setting internal port failed: %d\n", err);
+ return err;
+ }
+ }
+ }
+
+#ifdef DEBUG
+ {
+ char *buffer = kzalloc(0x5000, GFP_KERNEL);
+
+ err = regmap_bulk_read(hub->regmap, 0, buffer, 0x5000);
+ print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buffer, 0x5000);
+ kfree(buffer);
+ }
+#endif
+
+ /*
+ * attach
+ */
+ attach_buffer[0] = 0xAA; /* USB attach (high byte) */
+ attach_buffer[1] = 0x55; /* USB attach (low byte) */
+ attach_buffer[2] = 0x00; /* terminator */
+
+ err = i2c_master_send(hub->i2c, attach_buffer, 3);
+ if (err != 3) {
+ dev_err(dev, "attaching hub failed: %d\n", err);
+ return err;
+ }
+
+ dev_info(dev, "Hub configuration was successful.\n");
+ return 0;
+
+}
+
+#ifdef CONFIG_OF
+static int usb253x_get_ofdata(struct usb253x *hub)
+{
+ struct device *dev = hub->dev;
+ struct device_node *np = dev->of_node;
+
+ if (!np) {
+ dev_err(dev, "failed to get ofdata\n");
+ return -ENODEV;
+ }
+
+ if (of_get_property(np, "skip-config", NULL))
+ hub->skip_config = 1;
+ else
+ hub->skip_config = 0;
+
+ hub->gpio_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(hub->gpio_reset))
+ return PTR_ERR(hub->gpio_reset);
+
+ return 0;
+}
+
+static const struct of_device_id usb253x_of_match[] = {
+ { .compatible = "microchip,usb2532", },
+ { .compatible = "microchip,usb2532i", },
+ { .compatible = "microchip,usb2533", },
+ { .compatible = "microchip,usb2533i", },
+ { .compatible = "microchip,usb2534", },
+ { .compatible = "microchip,usb2534i", },
+ { .compatible = "microchip,usb3613", },
+ { .compatible = "microchip,usb3613i", },
+ { .compatible = "microchip,usb3813", },
+ { .compatible = "microchip,usb3813i", },
+ { .compatible = "microchip,usb4604", },
+ { .compatible = "microchip,usb4604i", },
+ { .compatible = "microchip,usb4624", },
+ { .compatible = "microchip,usb4624i", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, usb253x_of_match);
+#else /* CONFIG_OF */
+static int usb253x_get_ofdata(struct usb253x *hub)
+{
+ return 0;
+}
+#endif /* CONFIG_OF */
+
+static void usb253x_regulator_disable_action(void *data)
+{
+ struct usb253x *hub = data;
+
+ regulator_disable(hub->vdd);
+}
+
+static int usb253x_probe(struct usb253x *hub)
+{
+ struct device *dev = hub->dev;
+ struct device_node *np = dev->of_node;
+ int err;
+
+ if (np) {
+ err = usb253x_get_ofdata(hub);
+ if (err) {
+ dev_err(dev, "failed to get ofdata: %d\n", err);
+ return err;
+ }
+ }
+
+ /*
+ * usb253x SMBus-slave SCL lane is muxed with CFG_SEL0 pin. So if anyone
+ * tries to work with the bus at the moment the hub reset is released,
+ * it may cause an invalid config being latched by usb253x. Particularly
+ * one of the config modes makes the hub loading a default registers
+ * value without SMBus-slave interface activation. If the hub
+ * accidentally gets this mode, this will cause the driver SMBus-
+ * functions failure. Normally we could just lock the SMBus-segment the
+ * hub i2c-interface resides for the device-specific reset timing. But
+ * the GPIO controller, which is used to handle the hub reset, might be
+ * placed at the same i2c-bus segment. In this case an error should be
+ * returned since we can't safely use the GPIO controller to clear the
+ * reset state (it may affect the hub configuration) and we can't lock
+ * the i2c-bus segment (it will cause a deadlock).
+ */
+ err = usb253x_check_gpio_chip(hub);
+ if (err)
+ return err;
+
+ hub->vdd = devm_regulator_get(dev, "vdd");
+ if (IS_ERR(hub->vdd))
+ return PTR_ERR(hub->vdd);
+
+ err = regulator_enable(hub->vdd);
+ if (err)
+ return err;
+
+ err = devm_add_action_or_reset(dev,
+ usb253x_regulator_disable_action, hub);
+ if (err)
+ return err;
+
+ err = usb253x_connect(hub);
+ if (err) {
+ dev_err(dev, "Failed to connect hub (%d)\n", err);
+ return err;
+ }
+
+ dev_info(dev, "Hub probed successfully\n");
+
+ return 0;
+}
+
+static int usb253x_i2c_gather_write(void *context,
+ const void *reg, size_t reg_len,
+ const void *val, size_t val_len)
+{
+ struct i2c_client *i2c = (struct i2c_client *)context;
+ size_t frame_len = val_len + 7;
+ char *buffer;
+ int err;
+
+ if (WARN_ON(reg_len != 2))
+ return -EINVAL;
+
+ buffer = kmalloc(frame_len, GFP_KERNEL);
+ if (!buffer)
+ return -ENOMEM;
+
+ buffer[0] = 0x00; /* Memory address (high byte) */
+ buffer[1] = 0x00; /* Memory address (low byte) */
+ buffer[2] = val_len + 4; /* Number of bytes to write to memory */
+ buffer[3] = 0x00; /* Register Write */
+ buffer[4] = val_len; /* Write val_len data bytes */
+ buffer[5] = *((const char *)reg + 0); /* Register address (high byte) */
+ buffer[6] = *((const char *)reg + 1); /* Register address (low byte) */
+ memcpy(&buffer[7], val, val_len);
+
+ err = i2c_master_send(i2c, buffer, frame_len);
+ if (err != (int)frame_len) {
+ dev_err(&i2c->dev, "Writing to hub memory failed: %d\n", err);
+ goto error_kfree;
+ }
+
+ buffer[0] = 0x99; /* Command (high byte) */
+ buffer[1] = 0x37; /* Command (low byte) */
+ buffer[2] = 0x00; /* Termination */
+ frame_len = 3;
+
+ err = i2c_master_send(i2c, buffer, frame_len);
+ if (err != (int)frame_len) {
+ dev_err(&i2c->dev, "Accessing configuration data failed: %d\n", err);
+ goto error_kfree;
+ }
+
+ err = 0;
+
+error_kfree:
+ kfree(buffer);
+ return err;
+}
+
+/* regmap puts address into data[0] and data[1]; value is in data[2] */
+static int usb253x_i2c_write(void *context, const void *data, size_t count)
+{
+ if (WARN_ON(count != 3))
+ return -EINVAL;
+
+ return usb253x_i2c_gather_write(context, data, 2, data + 2, 1);
+}
+
+static int usb253x_i2c_read(void *context, const void *reg_buf, size_t reg_size,
+ void *val_buf, size_t val_size)
+{
+ struct i2c_client *i2c = (struct i2c_client *)context;
+ char *tx, *rx;
+ int err;
+
+ if (WARN_ON(reg_size != 2)) {
+ err = -EINVAL;
+ goto error_return;
+ }
+
+ tx = kmalloc(7, GFP_KERNEL);
+ if (!tx) {
+ err = -ENOMEM;
+ goto error_return;
+ }
+
+ rx = kmalloc(1 + val_size, GFP_KERNEL);
+ if (!rx) {
+ err = -ENOMEM;
+ goto error_free_tx;
+ }
+
+ tx[0] = 0x00; /* Memory address (high byte) */
+ tx[1] = 0x00; /* Memory address (low byte) */
+ tx[2] = 4; /* Number of bytes to write to memory */
+ tx[3] = 0x01; /* Register Read */
+ tx[4] = val_size; /* Read val_size data bytes */
+ tx[5] = *((const char *)reg_buf + 0); /* Register address (high byte) */
+ tx[6] = *((const char *)reg_buf + 1); /* Register address (low byte) */
+
+ err = i2c_master_send(i2c, tx, 7);
+ if (err != 7) {
+ dev_err(&i2c->dev, "Writing to hub memory failed: %d\n", err);
+ goto error_free_rx;
+ }
+
+ tx[0] = 0x99; /* Command (high byte) */
+ tx[1] = 0x37; /* Command (low byte) */
+ tx[2] = 0x00; /* Termination */
+
+ err = i2c_master_send(i2c, tx, 3);
+ if (err != 3) {
+ dev_err(&i2c->dev, "Accessing configuration data failed: %d\n", err);
+ goto error_free_rx;
+ }
+
+ /* Read from hub memory address 4 (according to application note) */
+ tx[0] = 0x00; /* Memory address (high byte) */
+ tx[1] = 0x04; /* Memory address (low byte) */
+
+ {
+ struct i2c_msg msgs[] = {
+ {
+ .addr = i2c->addr, .flags = 0,
+ .len = 2, .buf = tx
+ },
+ {
+ .addr = i2c->addr, .flags = I2C_M_RD,
+ .len = 1 + val_size, .buf = rx
+ },
+ };
+
+ err = i2c_transfer(i2c->adapter, msgs, ARRAY_SIZE(msgs));
+ if (err < 0) {
+ dev_err(&i2c->dev, "Reading from hub memory failed: %d\n", err);
+ goto error_free_rx;
+ }
+ }
+
+ WARN_ON(rx[0] < val_size);
+
+ memcpy(val_buf, &rx[1], val_size);
+
+ err = 0;
+
+error_free_rx:
+ kfree(rx);
+error_free_tx:
+ kfree(tx);
+error_return:
+ return err;
+}
+
+/*
+ * The reason we need this custom regmap_bus instead of using regmap_init_i2c()
+ * is that accesses to the USB253x configuration memory have to be wrapped into
+ * a special protocol.
+ */
+static const struct regmap_bus usb253x_i2c_regmap = {
+ .write = usb253x_i2c_write,
+ .gather_write = usb253x_i2c_gather_write,
+ .read = usb253x_i2c_read,
+ .max_raw_read = 128,
+ .max_raw_write = 128,
+};
+
+/* Avoid reading bigger dead ranges inside hubs memory. Same table for
+ * read and write.
+ */
+static const struct regmap_range usb253x_regmap_yes_ranges[] = {
+ { .range_min = 0x0800, .range_max = 0x09ff },
+ { .range_min = 0x3000, .range_max = 0x31ff },
+ { .range_min = 0x3C00, .range_max = 0x3cff },
+ { .range_min = 0x4100, .range_max = 0x42ff },
+ { .range_min = 0x6000, .range_max = 0x72ff },
+};
+
+static const struct regmap_access_table usb253x_regmap_access_table = {
+ .yes_ranges = usb253x_regmap_yes_ranges,
+ .n_yes_ranges = ARRAY_SIZE(usb253x_regmap_yes_ranges),
+};
+
+static int usb253x_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id __always_unused)
+{
+ struct usb253x *hub;
+ struct regmap_config regmap_cfg = {
+ .name = "usb253x_config_mem",
+ .reg_bits = 16,
+ .val_bits = 8,
+ .max_register = 0x7fff,
+ .wr_table = &usb253x_regmap_access_table,
+ .rd_table = &usb253x_regmap_access_table,
+ .can_multi_write = 1,
+ };
+
+ hub = devm_kzalloc(&i2c->dev, sizeof(struct usb253x), GFP_KERNEL);
+ if (!hub)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, hub);
+ hub->dev = &i2c->dev;
+ hub->i2c = i2c;
+ hub->regmap = devm_regmap_init(&i2c->dev, &usb253x_i2c_regmap, i2c,
+ ®map_cfg);
+ if (IS_ERR(hub->regmap))
+ return PTR_ERR(hub->regmap);
+
+ return usb253x_probe(hub);
+}
+
+static int usb253x_i2c_remove(struct i2c_client *i2c)
+{
+ struct usb253x *hub = i2c_get_clientdata(i2c);
+
+ usb253x_reset(hub, 0);
+
+ return 0;
+};
+
+static int __maybe_unused usb253x_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct usb253x *hub = i2c_get_clientdata(client);
+
+ return regulator_disable(hub->vdd);
+}
+
+static int __maybe_unused usb253x_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct usb253x *hub = i2c_get_clientdata(client);
+ int err;
+
+ err = regulator_enable(hub->vdd);
+ if (err)
+ return err;
+
+ return usb253x_connect(hub);
+}
+
+static SIMPLE_DEV_PM_OPS(usb253x_pm_ops, usb253x_suspend, usb253x_resume);
+
+static const struct i2c_device_id usb253x_id[] = {
+ { "usb2532", 0 },
+ { "usb2532i", 0 },
+ { "usb2533", 0 },
+ { "usb2533i", 0 },
+ { "usb2534", 0 },
+ { "usb2534i", 0 },
+ { "usb3613", 0 },
+ { "usb3613i", 0 },
+ { "usb3813", 0 },
+ { "usb3813i", 0 },
+ { "usb4604", 0 },
+ { "usb4604i", 0 },
+ { "usb4624", 0 },
+ { "usb4624i", 0 },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, usb253x_id);
+
+static struct i2c_driver usb253x_i2c_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = of_match_ptr(usb253x_of_match),
+ .pm = &usb253x_pm_ops,
+ },
+ .probe = usb253x_i2c_probe,
+ .remove = usb253x_i2c_remove,
+ .id_table = usb253x_id,
+};
+
+module_i2c_driver(usb253x_i2c_driver);
+
+MODULE_AUTHOR("Christian Eggers <ceggers@arri.de>");
+MODULE_DESCRIPTION("USB253x/xi USB 2.0 Hub Controller Driver");
+MODULE_LICENSE("GPL");
This patch adds a driver for configuration of the Microchip USB253x/xi USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus configuration interface and two to four USB 2.0 downstream ports. Furthermore add myself as a maintainer for this driver. The datasheet can be found at the manufacturers website, see [1]. All device-tree exposed configuration features have been tested on a i.MX6 platform with a USB2534i hub. [1] http://ww1.microchip.com/downloads/en/AppNotes/00001801C.pdf Signed-off-by: Christian Eggers <ceggers@arri.de> --- MAINTAINERS | 7 + drivers/usb/misc/Kconfig | 10 + drivers/usb/misc/Makefile | 1 + drivers/usb/misc/usb253x.c | 834 +++++++++++++++++++++++++++++++++++++ 4 files changed, 852 insertions(+) create mode 100644 drivers/usb/misc/usb253x.c