new file mode 100644
@@ -0,0 +1,1463 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Cadence CDNSP DRD Driver.
+ *
+ * Copyright (C) 2020 Cadence.
+ *
+ * Author: Pawel Laszczak <pawell@cadence.com>
+ *
+ * Code based on Linux XHCI driver.
+ * Origin: Copyright (C) 2008 Intel Corp.
+ */
+#ifndef __LINUX_CDNSP_GADGET_H
+#define __LINUX_CDNSP_GADGET_H
+
+#include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/usb/gadget.h>
+#include <linux/irq.h>
+
+/* Max number slots - only 1 is allowed. */
+#define CDNSP_DEV_MAX_SLOTS 1
+
+#define CDNSP_EP0_SETUP_SIZE 512
+
+/* One control and 15 for in and 15 for out endpoints. */
+#define CDNSP_ENDPOINTS_NUM 31
+
+/* Best Effort Service Latency. */
+#define CDNSP_DEFAULT_BESL 0
+
+/* Device Controller command default timeout value in us */
+#define CDNSP_CMD_TIMEOUT (15 * 1000)
+
+/* Up to 16 ms to halt an device controller */
+#define CDNSP_MAX_HALT_USEC (16 * 1000)
+
+#define CDNSP_CTX_SIZE 2112
+
+/*
+ * Controller register interface.
+ */
+
+/**
+ * struct cdnsp_cap_regs - CDNSP Registers.
+ * @hc_capbase: Length of the capabilities register and controller
+ * version number
+ * @hcs_params1: HCSPARAMS1 - Structural Parameters 1
+ * @hcs_params2: HCSPARAMS2 - Structural Parameters 2
+ * @hcs_params3: HCSPARAMS3 - Structural Parameters 3
+ * @hcc_params: HCCPARAMS - Capability Parameters
+ * @db_off: DBOFF - Doorbell array offset
+ * @run_regs_off: RTSOFF - Runtime register space offset
+ * @hcc_params2: HCCPARAMS2 Capability Parameters 2,
+ */
+struct cdnsp_cap_regs {
+ __le32 hc_capbase;
+ __le32 hcs_params1;
+ __le32 hcs_params2;
+ __le32 hcs_params3;
+ __le32 hcc_params;
+ __le32 db_off;
+ __le32 run_regs_off;
+ __le32 hcc_params2;
+ /* Reserved up to (CAPLENGTH - 0x1C) */
+};
+
+/* hc_capbase bitmasks. */
+/* bits 7:0 - how long is the Capabilities register. */
+#define HC_LENGTH(p) (((p) >> 00) & GENMASK(7, 0))
+/* bits 31:16 */
+#define HC_VERSION(p) (((p) >> 16) & GENMASK(15, 1))
+
+/* HCSPARAMS1 - hcs_params1 - bitmasks */
+/* bits 0:7, Max Device Endpoints */
+#define HCS_ENDPOINTS_MASK GENMASK(7, 0)
+#define HCS_ENDPOINTS(p) (((p) & HCS_ENDPOINTS_MASK) >> 0)
+
+/* HCCPARAMS offset from PCI base address */
+#define HCC_PARAMS_OFFSET 0x10
+
+/* HCCPARAMS - hcc_params - bitmasks */
+/* 1: device controller can use 64-bit address pointers. */
+#define HCC_64BIT_ADDR(p) ((p) & BIT(0))
+/* 1: device controller uses 64-byte Device Context structures. */
+#define HCC_64BYTE_CONTEXT(p) ((p) & BIT(2))
+/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15. */
+#define HCC_MAX_PSA(p) ((((p) >> 12) & 0xf) + 1)
+/* Extended Capabilities pointer from PCI base. */
+#define HCC_EXT_CAPS(p) (((p) & GENMASK(31, 16)) >> 16)
+
+#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
+
+/* db_off bitmask - bits 0:1 reserved. */
+#define DBOFF_MASK GENMASK(31, 2)
+
+/* run_regs_off bitmask - bits 0:4 reserved. */
+#define RTSOFF_MASK GENMASK(31, 5)
+
+/**
+ * struct cdnsp_op_regs - Device Controller Operational Registers.
+ * @command: USBCMD - Controller command register.
+ * @status: USBSTS - Controller status register.
+ * @page_size: This indicates the page size that the device controller supports.
+ * If bit n is set, the controller supports a page size of 2^(n+12),
+ * up to a 128MB page size. 4K is the minimum page size.
+ * @dnctrl: DNCTRL - Device notification control register.
+ * @cmd_ring: CRP - 64-bit Command Ring Pointer.
+ * @dcbaa_ptr: DCBAAP - 64-bit Device Context Base Address Array Pointer.
+ * @config_reg: CONFIG - Configure Register
+ * @port_reg_base: PORTSCn - base address for Port Status and Control
+ * Each port has a Port Status and Control register,
+ * followed by a Port Power Management Status and Control
+ * register, a Port Link Info register, and a reserved
+ * register.
+ */
+struct cdnsp_op_regs {
+ __le32 command;
+ __le32 status;
+ __le32 page_size;
+ __le32 reserved1;
+ __le32 reserved2;
+ __le32 dnctrl;
+ __le64 cmd_ring;
+ /* rsvd: offset 0x20-2F. */
+ __le32 reserved3[4];
+ __le64 dcbaa_ptr;
+ __le32 config_reg;
+ /* rsvd: offset 0x3C-3FF. */
+ __le32 reserved4[241];
+ /* port 1 registers, which serve as a base address for other ports. */
+ __le32 port_reg_base;
+};
+
+/* Number of registers per port. */
+#define NUM_PORT_REGS 4
+
+/**
+ * struct cdnsp_port_regs - Port Registers.
+ * @portsc: PORTSC - Port Status and Control Register.
+ * @portpmsc: PORTPMSC - Port Power Managements Status and Control Register.
+ * @portli: PORTLI - Port Link Info register.
+ */
+struct cdnsp_port_regs {
+ __le32 portsc;
+ __le32 portpmsc;
+ __le32 portli;
+ __le32 reserved;
+};
+
+/*
+ * These bits are Read Only (RO) and should be saved and written to the
+ * registers: 0 (connect status) and 10:13 (port speed).
+ * These bits are also sticky - meaning they're in the AUX well and they aren't
+ * changed by a hot and warm.
+ */
+#define CDNSP_PORT_RO (PORT_CONNECT | DEV_SPEED_MASK)
+
+/*
+ * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit:
+ * bits 5:8 (link state), 25:26 ("wake on" enable state)
+ */
+#define CDNSP_PORT_RWS (PORT_PLS_MASK | PORT_WKCONN_E | PORT_WKDISC_E)
+
+/*
+ * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect:
+ * bits 1 (port enable/disable), 17 ( connect changed),
+ * 21 (port reset changed) , 22 (Port Link State Change),
+ */
+#define CDNSP_PORT_RW1CS (PORT_PED | PORT_CSC | PORT_RC | PORT_PLC)
+
+/* USBCMD - USB command - bitmasks. */
+/* Run/Stop, controller execution - do not write unless controller is halted.*/
+#define CMD_R_S BIT(0)
+/*
+ * Reset device controller - resets internal controller state machine and all
+ * registers (except PCI config regs).
+ */
+#define CMD_RESET BIT(1)
+/* Event Interrupt Enable - a '1' allows interrupts from the controller. */
+#define CMD_INTE BIT(2)
+/*
+ * Device System Error Interrupt Enable - get out-of-band signal for
+ * controller errors.
+ */
+#define CMD_DSEIE BIT(3)
+/* device controller save/restore state. */
+#define CMD_CSS BIT(8)
+#define CMD_CRS BIT(9)
+/*
+ * Enable Wrap Event - '1' means device controller generates an event
+ * when MFINDEX wraps.
+ */
+#define CMD_EWE BIT(10)
+/* 1: device enabled */
+#define CMD_DEVEN BIT(17)
+/* bits 18:31 are reserved (and should be preserved on writes). */
+
+/* Command register values to disable interrupts. */
+#define CDNSP_IRQS (CMD_INTE | CMD_DSEIE | CMD_EWE)
+
+/* USBSTS - USB status - bitmasks */
+/* controller not running - set to 1 when run/stop bit is cleared. */
+#define STS_HALT BIT(0)
+/*
+ * serious error, e.g. PCI parity error. The controller will clear
+ * the run/stop bit.
+ */
+#define STS_FATAL BIT(2)
+/* event interrupt - clear this prior to clearing any IP flags in IR set.*/
+#define STS_EINT BIT(3)
+/* port change detect */
+#define STS_PCD BIT(4)
+/* save state status - '1' means device controller is saving state. */
+#define STS_SSS BIT(8)
+/* restore state status - '1' means controllers is restoring state. */
+#define STS_RSS BIT(9)
+/* 1: save or restore error */
+#define STS_SRE BIT(10)
+/* 1: device Not Ready to accept doorbell or op reg writes after reset. */
+#define STS_CNR BIT(11)
+/* 1: internal Device Controller Error.*/
+#define STS_HCE BIT(12)
+
+/* CRCR - Command Ring Control Register - cmd_ring bitmasks. */
+/* bit 0 is the command ring cycle state. */
+#define CMD_RING_CS BIT(0)
+/* stop ring immediately - abort the currently executing command. */
+#define CMD_RING_ABORT BIT(2)
+/*
+ * Command Ring Busy.
+ * Set when Doorbell register is written with DB for command and cleared when
+ * the controller reached end of CR.
+ */
+#define CMD_RING_BUSY(p) ((p) & BIT(4))
+/* 1: command ring is running */
+#define CMD_RING_RUNNING BIT(3)
+/* Command Ring pointer - bit mask for the lower 32 bits. */
+#define CMD_RING_RSVD_BITS GENMASK(5, 0)
+
+/* CONFIG - Configure Register - config_reg bitmasks. */
+/* bits 0:7 - maximum number of device slots enabled. */
+#define MAX_DEVS GENMASK(7, 0)
+/* bit 8: U3 Entry Enabled, assert PLC when controller enters U3. */
+#define CONFIG_U3E BIT(8)
+
+/* PORTSC - Port Status and Control Register - port_reg_base bitmasks */
+/* 1: device connected. */
+#define PORT_CONNECT BIT(0)
+/* 1: port enabled. */
+#define PORT_PED BIT(1)
+/* 1: port reset signaling asserted. */
+#define PORT_RESET BIT(4)
+/*
+ * Port Link State - bits 5:8
+ * A read gives the current link PM state of the port,
+ * a write with Link State Write Strobe sets the link state.
+ */
+#define PORT_PLS_MASK GENMASK(8, 5)
+#define XDEV_U0 (0x0 << 5)
+#define XDEV_U1 (0x1 << 5)
+#define XDEV_U2 (0x2 << 5)
+#define XDEV_U3 (0x3 << 5)
+#define XDEV_DISABLED (0x4 << 5)
+#define XDEV_RXDETECT (0x5 << 5)
+#define XDEV_INACTIVE (0x6 << 5)
+#define XDEV_POLLING (0x7 << 5)
+#define XDEV_RECOVERY (0x8 << 5)
+#define XDEV_HOT_RESET (0x9 << 5)
+#define XDEV_COMP_MODE (0xa << 5)
+#define XDEV_TEST_MODE (0xb << 5)
+#define XDEV_RESUME (0xf << 5)
+/* 1: port has power. */
+#define PORT_POWER BIT(9)
+/*
+ * bits 10:13 indicate device speed:
+ * 0 - undefined speed - port hasn't be initialized by a reset yet
+ * 1 - full speed
+ * 2 - Reserved (Low Speed not supported
+ * 3 - high speed
+ * 4 - super speed
+ * 5 - super speed
+ * 6-15 reserved
+ */
+#define DEV_SPEED_MASK GENMASK(13, 10)
+#define XDEV_FS (0x1 << 10)
+#define XDEV_HS (0x3 << 10)
+#define XDEV_SS (0x4 << 10)
+#define XDEV_SSP (0x5 << 10)
+#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0 << 10))
+#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
+#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
+#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
+#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
+#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
+#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
+/* Port Link State Write Strobe - set this when changing link state */
+#define PORT_LINK_STROBE BIT(16)
+/* 1: connect status change */
+#define PORT_CSC BIT(17)
+/* 1: warm reset for a USB 3.0 device is done. */
+#define PORT_WRC BIT(19)
+/* 1: reset change - 1 to 0 transition of PORT_RESET */
+#define PORT_RC BIT(21)
+/*
+ * port link status change - set on some port link state transitions:
+ * Transition Reason
+ * ----------------------------------------------------------------------------
+ * - U3 to Resume Wakeup signaling from a device
+ * - Resume to Recovery to U0 USB 3.0 device resume
+ * - Resume to U0 USB 2.0 device resume
+ * - U3 to Recovery to U0 Software resume of USB 3.0 device complete
+ * - U3 to U0 Software resume of USB 2.0 device complete
+ * - U2 to U0 L1 resume of USB 2.1 device complete
+ * - U0 to U0 L1 entry rejection by USB 2.1 device
+ * - U0 to disabled L1 entry error with USB 2.1 device
+ * - Any state to inactive Error on USB 3.0 port
+ */
+#define PORT_PLC BIT(22)
+/* Port configure error change - port failed to configure its link partner. */
+#define PORT_CEC BIT(23)
+/* Wake on connect (enable). */
+#define PORT_WKCONN_E BIT(25)
+/* Wake on disconnect (enable). */
+#define PORT_WKDISC_E BIT(26)
+/* Indicates if Warm Reset is being received. */
+#define PORT_WR BIT(31)
+
+#define PORT_CHANGE_BITS (PORT_CSC | PORT_WRC | PORT_RC | PORT_PLC | PORT_CEC)
+
+/* PORTPMSCUSB3 - Port Power Management Status and Control - bitmasks. */
+/* Enables U1 entry. */
+#define PORT_U1_TIMEOUT_MASK GENMASK(7, 0)
+#define PORT_U1_TIMEOUT(p) ((p) & PORT_U1_TIMEOUT_MASK)
+/* Enables U2 entry .*/
+#define PORT_U2_TIMEOUT_MASK GENMASK(14, 8)
+#define PORT_U2_TIMEOUT(p) (((p) << 8) & PORT_U2_TIMEOUT_MASK)
+
+/* PORTPMSCUSB2 - Port Power Management Status and Control - bitmasks. */
+#define PORT_L1S_MASK GENMASK(2, 0)
+#define PORT_L1S(p) ((p) & PORT_L1S_MASK)
+#define PORT_L1S_ACK PORT_L1S(1)
+#define PORT_L1S_NYET PORT_L1S(2)
+#define PORT_L1S_STALL PORT_L1S(3)
+#define PORT_L1S_TIMEOUT PORT_L1S(4)
+/* Remote Wake Enable. */
+#define PORT_RWE BIT(3)
+/* Best Effort Service Latency (BESL). */
+#define PORT_BESL(p) (((p) << 4) & GENMASK(7, 4))
+/* Hardware LPM Enable (HLE). */
+#define PORT_HLE BIT(16)
+/* Received Best Effort Service Latency (BESL). */
+#define PORT_RRBESL(p) (((p) & GENMASK(20, 17)) >> 17)
+/* Port Test Control. */
+#define PORT_TEST_MODE_MASK GENMASK(31, 28)
+#define PORT_TEST_MODE(p) (((p) << 28) & PORT_TEST_MODE_MASK)
+
+/**
+ * struct cdnsp_intr_reg - Interrupt Register Set.
+ * @irq_pending: IMAN - Interrupt Management Register. Used to enable
+ * interrupts and check for pending interrupts.
+ * @irq_control: IMOD - Interrupt Moderation Register.
+ * Used to throttle interrupts.
+ * @erst_size: Number of segments in the Event Ring Segment Table (ERST).
+ * @erst_base: ERST base address.
+ * @erst_dequeue: Event ring dequeue pointer.
+ *
+ * Each interrupter (defined by a MSI-X vector) has an event ring and an Event
+ * Ring Segment Table (ERST) associated with it. The event ring is comprised of
+ * multiple segments of the same size. The controller places events on the ring
+ * and "updates the Cycle bit in the TRBs to indicate to software the current
+ * position of the Enqueue Pointer." The driver processes those events and
+ * updates the dequeue pointer.
+ */
+struct cdnsp_intr_reg {
+ __le32 irq_pending;
+ __le32 irq_control;
+ __le32 erst_size;
+ __le32 rsvd;
+ __le64 erst_base;
+ __le64 erst_dequeue;
+};
+
+/* IMAN - Interrupt Management Register - irq_pending bitmasks l. */
+#define IMAN_IE BIT(1)
+#define IMAN_IP BIT(0)
+/* bits 2:31 need to be preserved */
+#define IMAN_IE_SET(p) (((p) & IMAN_IE) | 0x2)
+#define IMAN_IE_CLEAR(p) (((p) & IMAN_IE) & ~(0x2))
+
+/* IMOD - Interrupter Moderation Register - irq_control bitmasks. */
+/*
+ * Minimum interval between interrupts (in 250ns intervals). The interval
+ * between interrupts will be longer if there are no events on the event ring.
+ * Default is 4000 (1 ms).
+ */
+#define IMOD_INTERVAL_MASK GENMASK(15, 0)
+/* Counter used to count down the time to the next interrupt - HW use only */
+#define IMOD_COUNTER_MASK GENMASK(31, 16)
+#define IMOD_DEFAULT_INTERVAL 0
+
+/* erst_size bitmasks. */
+/* Preserve bits 16:31 of erst_size. */
+#define ERST_SIZE_MASK GENMASK(31, 16)
+
+/* erst_dequeue bitmasks. */
+/*
+ * Dequeue ERST Segment Index (DESI) - Segment number (or alias)
+ * where the current dequeue pointer lies. This is an optional HW hint.
+ */
+#define ERST_DESI_MASK GENMASK(2, 0)
+/* Event Handler Busy (EHB) - is the event ring scheduled to be serviced. */
+#define ERST_EHB BIT(3)
+#define ERST_PTR_MASK GENMASK(3, 0)
+
+/**
+ * struct cdnsp_run_regs
+ * @microframe_index: MFINDEX - current microframe number.
+ * @ir_set: Array of Interrupter registers.
+ *
+ * Device Controller Runtime Registers:
+ * "Software should read and write these registers using only Dword (32 bit)
+ * or larger accesses"
+ */
+struct cdnsp_run_regs {
+ __le32 microframe_index;
+ __le32 rsvd[7];
+ struct cdnsp_intr_reg ir_set[128];
+};
+
+/**
+ * USB2.0 Port Peripheral Configuration Registers.
+ * @ext_cap: Header register for Extended Capability.
+ * @port_reg1: Timer Configuration Register.
+ * @port_reg2: Timer Configuration Register.
+ * @port_reg3: Timer Configuration Register.
+ * @port_reg4: Timer Configuration Register.
+ * @port_reg5: Timer Configuration Register.
+ * @port_reg6: Chicken bits for USB20PPP.
+ */
+struct cdnsp_20port_cap {
+ __le32 ext_cap;
+ __le32 port_reg1;
+ __le32 port_reg2;
+ __le32 port_reg3;
+ __le32 port_reg4;
+ __le32 port_reg5;
+ __le32 port_reg6;
+};
+
+/* Extended capability register fields */
+#define EXT_CAPS_ID(p) (((p) >> 0) & GENMASK(7, 0))
+#define EXT_CAPS_NEXT(p) (((p) >> 8) & GENMASK(7, 0))
+/* Extended capability IDs - ID 0 reserved */
+#define EXT_CAPS_PROTOCOL 2
+
+/* USB 2.0 Port Peripheral Configuration Extended Capability */
+#define EXT_CAP_CFG_DEV_20PORT_CAP_ID 0xC1
+/*
+ * Setting this bit to '1' enables automatic wakeup from L1 state on transfer
+ * TRB prepared when USBSSP operates in USB2.0 mode.
+ */
+#define PORT_REG6_L1_L0_HW_EN BIT(1)
+/*
+ * Setting this bit to '1' forces Full Speed when USBSSP operates in USB2.0
+ * mode (disables High Speed).
+ */
+#define PORT_REG6_FORCE_FS BIT(0)
+
+/**
+ * USB3.x Port Peripheral Configuration Registers.
+ * @ext_cap: Header register for Extended Capability.
+ * @mode_addr: Miscellaneous 3xPORT operation mode configuration register.
+ * @mode_2: 3x Port Control Register 2.
+ */
+struct cdnsp_3xport_cap {
+ __le32 ext_cap;
+ __le32 mode_addr;
+ __le32 reserved[52];
+ __le32 mode_2;
+};
+
+/* Extended Capability Header for 3XPort Configuration Registers. */
+#define D_XEC_CFG_3XPORT_CAP 0xC0
+#define CFG_3XPORT_SSP_SUPPORT BIT(31)
+#define CFG_3XPORT_U1_PIPE_CLK_GATE_EN BIT(0)
+
+/* Revision Extended Capability ID */
+#define RTL_REV_CAP 0xC4
+#define RTL_REV_CAP_RX_BUFF_CMD_SIZE BITMASK(31, 24)
+#define RTL_REV_CAP_RX_BUFF_SIZE BITMASK(15, 0)
+#define RTL_REV_CAP_TX_BUFF_CMD_SIZE BITMASK(31, 24)
+#define RTL_REV_CAP_TX_BUFF_SIZE BITMASK(15, 0)
+
+#define CDNSP_VER_1 0x00000000
+#define CDNSP_VER_2 0x10000000
+
+#define CDNSP_IF_EP_EXIST(pdev, ep_num, dir) ((pdev)->rev_cap.ep_supported & \
+ (BIT(ep_num) << ((dir) ? 0 : 16)))
+
+/**
+ * struct cdnsp_rev_cap - controller capabilities .
+ * @ext_cap: Header for RTL Revision Extended Capability.
+ * @rtl_revision: RTL revision.
+ * @rx_buff_size: Rx buffer sizes.
+ * @tx_buff_size: Tx buffer sizes.
+ * @ep_supported: Supported endpoints.
+ * @ctrl_revision: Controller revision ID.
+ */
+struct cdnsp_rev_cap {
+ __le32 ext_cap;
+ __le32 rtl_revision;
+ __le32 rx_buff_size;
+ __le32 tx_buff_size;
+ __le32 ep_supported;
+ __le32 ctrl_revision;
+};
+
+/* USB2.0 Port Peripheral Configuration Registers. */
+#define D_XEC_PRE_REGS_CAP 0xC8
+#define REG_CHICKEN_BITS_2_OFFSET 0x48
+#define CHICKEN_XDMA_2_TP_CACHE_DIS BIT(28)
+
+/* XBUF Extended Capability ID. */
+#define XBUF_CAP_ID 0xCB
+#define XBUF_RX_TAG_MASK_0_OFFSET 0x1C
+#define XBUF_RX_TAG_MASK_1_OFFSET 0x24
+#define XBUF_TX_CMD_OFFSET 0x2C
+
+/**
+ * struct cdnsp_doorbell_array.
+ * @cmd_db: Command ring doorbell register.
+ * @ep_db: Endpoint ring doorbell register.
+ * Bits 0 - 7: Endpoint target.
+ * Bits 8 - 15: RsvdZ.
+ * Bits 16 - 31: Stream ID.
+ */
+struct cdnsp_doorbell_array {
+ __le32 cmd_db;
+ __le32 ep_db;
+};
+
+#define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16))
+#define DB_VALUE_EP0_OUT(ep, stream) ((ep) & 0xff)
+#define DB_VALUE_CMD 0x00000000
+
+/**
+ * struct cdnsp_container_ctx.
+ * @type: Type of context. Used to calculated offsets to contained contexts.
+ * @size: Size of the context data.
+ * @ctx_size: context data structure size - 64 or 32 bits.
+ * @dma: dma address of the bytes.
+ * @bytes: The raw context data given to HW.
+ *
+ * Represents either a Device or Input context. Holds a pointer to the raw
+ * memory used for the context (bytes) and dma address of it (dma).
+ */
+struct cdnsp_container_ctx {
+ unsigned int type;
+#define CDNSP_CTX_TYPE_DEVICE 0x1
+#define CDNSP_CTX_TYPE_INPUT 0x2
+ int size;
+ int ctx_size;
+ dma_addr_t dma;
+ u8 *bytes;
+};
+
+/**
+ * struct cdnsp_slot_ctx
+ * @dev_info: Device speed, and last valid endpoint.
+ * @dev_port: Device port number that is needed to access the USB device.
+ * @int_target: Interrupter target number.
+ * @dev_state: Slot state and device address.
+ *
+ * Slot Context - This assumes the controller uses 32-byte context
+ * structures. If the controller uses 64-byte contexts, there is an additional
+ * 32 bytes reserved at the end of the slot context for controller internal use.
+ */
+struct cdnsp_slot_ctx {
+ __le32 dev_info;
+ __le32 dev_port;
+ __le32 int_target;
+ __le32 dev_state;
+ /* offset 0x10 to 0x1f reserved for controller internal use. */
+ __le32 reserved[4];
+};
+
+/* Bits 20:23 in the Slot Context are the speed for the device. */
+#define SLOT_SPEED_FS (XDEV_FS << 10)
+#define SLOT_SPEED_HS (XDEV_HS << 10)
+#define SLOT_SPEED_SS (XDEV_SS << 10)
+#define SLOT_SPEED_SSP (XDEV_SSP << 10)
+
+/* dev_info bitmasks. */
+/* Device speed - values defined by PORTSC Device Speed field - 20:23. */
+#define DEV_SPEED GENMASK(23, 20)
+#define GET_DEV_SPEED(n) (((n) & DEV_SPEED) >> 20)
+/* Index of the last valid endpoint context in this device context - 27:31. */
+#define LAST_CTX_MASK GENMASK(31, 27)
+#define LAST_CTX(p) ((p) << 27)
+#define LAST_CTX_TO_EP_NUM(p) (((p) >> 27) - 1)
+#define SLOT_FLAG BIT(0)
+#define EP0_FLAG BIT(1)
+
+/* dev_port bitmasks */
+/* Device port number that is needed to access the USB device. */
+#define DEV_PORT(p) (((p) & 0xff) << 16)
+
+/* dev_state bitmasks */
+/* USB device address - assigned by the controller. */
+#define DEV_ADDR_MASK GENMASK(7, 0)
+/* Slot state */
+#define SLOT_STATE GENMASK(31, 27)
+#define GET_SLOT_STATE(p) (((p) & SLOT_STATE) >> 27)
+
+#define SLOT_STATE_DISABLED 0
+#define SLOT_STATE_ENABLED SLOT_STATE_DISABLED
+#define SLOT_STATE_DEFAULT 1
+#define SLOT_STATE_ADDRESSED 2
+#define SLOT_STATE_CONFIGURED 3
+
+/**
+ * struct cdnsp_ep_ctx.
+ * @ep_info: Endpoint state, streams, mult, and interval information.
+ * @ep_info2: Information on endpoint type, max packet size, max burst size,
+ * error count, and whether the controller will force an event for
+ * all transactions.
+ * @deq: 64-bit ring dequeue pointer address. If the endpoint only
+ * defines one stream, this points to the endpoint transfer ring.
+ * Otherwise, it points to a stream context array, which has a
+ * ring pointer for each flow.
+ * @tx_info: Average TRB lengths for the endpoint ring and
+ * max payload within an Endpoint Service Interval Time (ESIT).
+ *
+ * Endpoint Context - This assumes the controller uses 32-byte context
+ * structures. If the controller uses 64-byte contexts, there is an additional
+ * 32 bytes reserved at the end of the endpoint context for controller internal
+ * use.
+ */
+struct cdnsp_ep_ctx {
+ __le32 ep_info;
+ __le32 ep_info2;
+ __le64 deq;
+ __le32 tx_info;
+ /* offset 0x14 - 0x1f reserved for controller internal use. */
+ __le32 reserved[3];
+};
+
+/* ep_info bitmasks. */
+/*
+ * Endpoint State - bits 0:2:
+ * 0 - disabled
+ * 1 - running
+ * 2 - halted due to halt condition
+ * 3 - stopped
+ * 4 - TRB error
+ * 5-7 - reserved
+ */
+#define EP_STATE_MASK GENMASK(3, 0)
+#define EP_STATE_DISABLED 0
+#define EP_STATE_RUNNING 1
+#define EP_STATE_HALTED 2
+#define EP_STATE_STOPPED 3
+#define EP_STATE_ERROR 4
+#define GET_EP_CTX_STATE(ctx) (le32_to_cpu((ctx)->ep_info) & EP_STATE_MASK)
+
+/* Mult - Max number of burst within an interval, in EP companion desc. */
+#define EP_MULT(p) (((p) << 8) & GENMASK(9, 8))
+#define CTX_TO_EP_MULT(p) (((p) & GENMASK(9, 8)) >> 8)
+/* bits 10:14 are Max Primary Streams. */
+/* bit 15 is Linear Stream Array. */
+/* Interval - period between requests to an endpoint - 125u increments. */
+#define EP_INTERVAL(p) (((p) << 16) & GENMASK(23, 16))
+#define EP_INTERVAL_TO_UFRAMES(p) (1 << (((p) & GENMASK(23, 16)) >> 16))
+#define CTX_TO_EP_INTERVAL(p) (((p) & GENMASK(23, 16)) >> 16)
+#define EP_MAXPSTREAMS_MASK GENMASK(14, 10)
+#define EP_MAXPSTREAMS(p) (((p) << 10) & EP_MAXPSTREAMS_MASK)
+#define CTX_TO_EP_MAXPSTREAMS(p) (((p) & EP_MAXPSTREAMS_MASK) >> 10)
+/* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */
+#define EP_HAS_LSA BIT(15)
+
+/* ep_info2 bitmasks */
+#define ERROR_COUNT(p) (((p) & 0x3) << 1)
+#define CTX_TO_EP_TYPE(p) (((p) >> 3) & 0x7)
+#define EP_TYPE(p) ((p) << 3)
+#define ISOC_OUT_EP 1
+#define BULK_OUT_EP 2
+#define INT_OUT_EP 3
+#define CTRL_EP 4
+#define ISOC_IN_EP 5
+#define BULK_IN_EP 6
+#define INT_IN_EP 7
+/* bit 6 reserved. */
+/* bit 7 is Device Initiate Disable - for disabling stream selection. */
+#define MAX_BURST(p) (((p) << 8) & GENMASK(15, 8))
+#define CTX_TO_MAX_BURST(p) (((p) & GENMASK(15, 8)) >> 8)
+#define MAX_PACKET(p) (((p) << 16) & GENMASK(31, 16))
+#define MAX_PACKET_MASK GENMASK(31, 16)
+#define MAX_PACKET_DECODED(p) (((p) & GENMASK(31, 16)) >> 16)
+
+/* tx_info bitmasks. */
+#define EP_AVG_TRB_LENGTH(p) ((p) & GENMASK(15, 0))
+#define EP_MAX_ESIT_PAYLOAD_LO(p) (((p) << 16) & GENMASK(31, 16))
+#define EP_MAX_ESIT_PAYLOAD_HI(p) ((((p) & GENMASK(23, 16)) >> 16) << 24)
+#define CTX_TO_MAX_ESIT_PAYLOAD_LO(p) (((p) & GENMASK(31, 16)) >> 16)
+#define CTX_TO_MAX_ESIT_PAYLOAD_HI(p) (((p) & GENMASK(31, 24)) >> 24)
+
+/* deq bitmasks. */
+#define EP_CTX_CYCLE_MASK BIT(0)
+#define CTX_DEQ_MASK (~0xfL)
+
+/**
+ * struct cdnsp_input_control_context
+ * Input control context;
+ *
+ * @drop_context: Set the bit of the endpoint context you want to disable.
+ * @add_context: Set the bit of the endpoint context you want to enable.
+ */
+struct cdnsp_input_control_ctx {
+ __le32 drop_flags;
+ __le32 add_flags;
+ __le32 rsvd2[6];
+};
+
+/**
+ * Represents everything that is needed to issue a command on the command ring.
+ *
+ * @in_ctx: Pointer to input context structure.
+ * @status: Command Completion Code for last command.
+ * @command_trb: Pointer to command TRB.
+ */
+struct cdnsp_command {
+ /* Input context for changing device state. */
+ struct cdnsp_container_ctx *in_ctx;
+ u32 status;
+ union cdnsp_trb *command_trb;
+};
+
+/**
+ * Stream context structure.
+ *
+ * @stream_ring: 64-bit stream ring address, cycle state, and stream type.
+ * @reserved: offset 0x14 - 0x1f reserved for controller internal use.
+ */
+struct cdnsp_stream_ctx {
+ __le64 stream_ring;
+ __le32 reserved[2];
+};
+
+/* Stream Context Types - bits 3:1 of stream ctx deq ptr. */
+#define SCT_FOR_CTX(p) (((p) << 1) & GENMASK(3, 1))
+/* Secondary stream array type, dequeue pointer is to a transfer ring. */
+#define SCT_SEC_TR 0
+/* Primary stream array type, dequeue pointer is to a transfer ring. */
+#define SCT_PRI_TR 1
+
+/**
+ * struct cdnsp_stream_info: Representing everything that is needed to
+ * supports stream capable endpoints.
+ * @stream_rings: Array of pointers containing Transfer rings for all
+ * supported streams.
+ * @num_streams: Number of streams, including stream 0.
+ * @stream_ctx_array: The stream context array may be bigger than the number
+ * of streams the driver asked for.
+ * @num_stream_ctxs: Number of streams.
+ * @ctx_array_dma: Dma address of Context Stream Array.
+ * @trb_address_map: For mapping physical TRB addresses to segments in
+ * stream rings.
+ * @td_count: Number of TDs associated with endpoint.
+ * @first_prime_det: First PRIME packet detected.
+ * @drbls_count: Number of allowed doorbells.
+ */
+struct cdnsp_stream_info {
+ struct cdnsp_ring **stream_rings;
+ unsigned int num_streams;
+ struct cdnsp_stream_ctx *stream_ctx_array;
+ unsigned int num_stream_ctxs;
+ dma_addr_t ctx_array_dma;
+ struct radix_tree_root trb_address_map;
+ int td_count;
+ u8 first_prime_det;
+#define STREAM_DRBL_FIFO_DEPTH 2
+ u8 drbls_count;
+};
+
+#define STREAM_LOG_STREAMS 4
+#define STREAM_NUM_STREAMS BIT(STREAM_LOG_STREAMS)
+
+#if STREAM_LOG_STREAMS > 16 && STREAM_LOG_STREAMS < 1
+#error "Not suupported stream value"
+#endif
+
+/**
+ * struct cdnsp_ep - extended device side representation of USB endpoint.
+ * @endpoint: usb endpoint
+ * @pending_req_list: List of requests queuing on transfer ring.
+ * @pdev: Device associated with this endpoint.
+ * @number: Endpoint number (1 - 15).
+ * idx: The device context index (DCI).
+ * interval: Interval between packets used for ISOC endpoint.
+ * @name: A human readable name e.g. ep1out.
+ * @direction: Endpoint direction.
+ * @buffering: Number of on-chip buffers related to endpoint.
+ * @buffering_period; Number of on-chip buffers related to periodic endpoint.
+ * @in_ctx: Pointer to input endpoint context structure.
+ * @out_ctx: Pointer to output endpoint context structure.
+ * @ring: Pointer to transfer ring.
+ * @stream_info: Hold stream information.
+ * @ep_state: Current state of endpoint.
+ * @skip: Sometimes the controller can not process isochronous endpoint ring
+ * quickly enough, and it will miss some isoc tds on the ring and
+ * generate Missed Service Error Event.
+ * Set skip flag when receive a Missed Service Error Event and
+ * process the missed tds on the endpoint ring.
+ */
+struct cdnsp_ep {
+ struct usb_ep endpoint;
+ struct list_head pending_list;
+ struct cdnsp_device *pdev;
+ u8 number;
+ u8 idx;
+ u32 interval;
+ char name[20];
+ u8 direction;
+ u8 buffering;
+ u8 buffering_period;
+ struct cdnsp_ep_ctx *in_ctx;
+ struct cdnsp_ep_ctx *out_ctx;
+ struct cdnsp_ring *ring;
+ struct cdnsp_stream_info stream_info;
+ unsigned int ep_state;
+#define EP_ENABLED BIT(0)
+#define EP_DIS_IN_RROGRESS BIT(1)
+#define EP_HALTED BIT(2)
+#define EP_STOPPED BIT(3)
+#define EP_WEDGE BIT(4)
+#define EP0_HALTED_STATUS BIT(5)
+#define EP_HAS_STREAMS BIT(6)
+
+ bool skip;
+};
+
+/**
+ * struct cdnsp_device_context_array
+ * @dev_context_ptr: Array of 64-bit DMA addresses for device contexts.
+ * @dma: DMA address for device contexts structure.
+ */
+struct cdnsp_device_context_array {
+ __le64 dev_context_ptrs[CDNSP_DEV_MAX_SLOTS + 1];
+ dma_addr_t dma;
+};
+
+/**
+ * struct cdnsp_transfer_event.
+ * @buffer: 64-bit buffer address, or immediate data.
+ * @transfer_len: Data length transferred.
+ * @flags: Field is interpreted differently based on the type of TRB.
+ */
+struct cdnsp_transfer_event {
+ __le64 buffer;
+ __le32 transfer_len;
+ __le32 flags;
+};
+
+/* Invalidate event after disabling endpoint. */
+#define TRB_EVENT_INVALIDATE 8
+
+/* Transfer event TRB length bit mask. */
+/* bits 0:23 */
+#define EVENT_TRB_LEN(p) ((p) & GENMASK(23, 0))
+/* Completion Code - only applicable for some types of TRBs */
+#define COMP_CODE_MASK (0xff << 24)
+#define GET_COMP_CODE(p) (((p) & COMP_CODE_MASK) >> 24)
+#define COMP_INVALID 0
+#define COMP_SUCCESS 1
+#define COMP_DATA_BUFFER_ERROR 2
+#define COMP_BABBLE_DETECTED_ERROR 3
+#define COMP_TRB_ERROR 5
+#define COMP_RESOURCE_ERROR 7
+#define COMP_NO_SLOTS_AVAILABLE_ERROR 9
+#define COMP_INVALID_STREAM_TYPE_ERROR 10
+#define COMP_SLOT_NOT_ENABLED_ERROR 11
+#define COMP_ENDPOINT_NOT_ENABLED_ERROR 12
+#define COMP_SHORT_PACKET 13
+#define COMP_RING_UNDERRUN 14
+#define COMP_RING_OVERRUN 15
+#define COMP_VF_EVENT_RING_FULL_ERROR 16
+#define COMP_PARAMETER_ERROR 17
+#define COMP_CONTEXT_STATE_ERROR 19
+#define COMP_EVENT_RING_FULL_ERROR 21
+#define COMP_INCOMPATIBLE_DEVICE_ERROR 22
+#define COMP_MISSED_SERVICE_ERROR 23
+#define COMP_COMMAND_RING_STOPPED 24
+#define COMP_COMMAND_ABORTED 25
+#define COMP_STOPPED 26
+#define COMP_STOPPED_LENGTH_INVALID 27
+#define COMP_STOPPED_SHORT_PACKET 28
+#define COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR 29
+#define COMP_ISOCH_BUFFER_OVERRUN 31
+#define COMP_EVENT_LOST_ERROR 32
+#define COMP_UNDEFINED_ERROR 33
+#define COMP_INVALID_STREAM_ID_ERROR 34
+
+/*Transfer Event NRDY bit fields */
+#define TRB_TO_DEV_STREAM(p) ((p) & GENMASK(16, 0))
+#define TRB_TO_HOST_STREAM(p) ((p) & GENMASK(16, 0))
+#define STREAM_PRIME_ACK 0xFFFE
+#define STREAM_REJECTED 0xFFFF
+
+/** Transfer Event bit fields **/
+#define TRB_TO_EP_ID(p) (((p) & GENMASK(20, 16)) >> 16)
+
+/**
+ * struct cdnsp_link_trb
+ * @segment_ptr: 64-bit segment pointer.
+ * @intr_target: Interrupter target.
+ * @control: Flags.
+ */
+struct cdnsp_link_trb {
+ __le64 segment_ptr;
+ __le32 intr_target;
+ __le32 control;
+};
+
+/* control bitfields */
+#define LINK_TOGGLE BIT(1)
+
+/**
+ * struct cdnsp_event_cmd - Command completion event TRB.
+ * cmd_trb: Pointer to command TRB, or the value passed by the event data trb
+ * status: Command completion parameters and error code.
+ * flags: Flags.
+ */
+struct cdnsp_event_cmd {
+ __le64 cmd_trb;
+ __le32 status;
+ __le32 flags;
+};
+
+/* flags bitmasks */
+
+/* Address device - disable SetAddress. */
+#define TRB_BSR BIT(9)
+
+/* Configure Endpoint - Deconfigure. */
+#define TRB_DC BIT(9)
+
+/* Force Header */
+#define TRB_FH_TO_PACKET_TYPE(p) ((p) & GENMASK(4, 0))
+#define TRB_FH_TR_PACKET 0x4
+#define TRB_FH_TO_DEVICE_ADDRESS(p) (((p) << 25) & GENMASK(31, 25))
+#define TRB_FH_TR_PACKET_DEV_NOT 0x6
+#define TRB_FH_TO_NOT_TYPE(p) (((p) << 4) & GENMASK(7, 4))
+#define TRB_FH_TR_PACKET_FUNCTION_WAKE 0x1
+#define TRB_FH_TO_INTERFACE(p) (((p) << 8) & GENMASK(15, 8))
+
+enum cdnsp_setup_dev {
+ SETUP_CONTEXT_ONLY,
+ SETUP_CONTEXT_ADDRESS,
+};
+
+/* bits 24:31 are the slot ID. */
+#define TRB_TO_SLOT_ID(p) (((p) & GENMASK(31, 24)) >> 24)
+#define SLOT_ID_FOR_TRB(p) (((p) << 24) & GENMASK(31, 24))
+
+/* Stop Endpoint TRB - ep_index to endpoint ID for this TRB. */
+#define TRB_TO_EP_INDEX(p) (((p) >> 16) & 0x1f)
+
+#define EP_ID_FOR_TRB(p) ((((p) + 1) << 16) & GENMASK(20, 16))
+
+#define SUSPEND_PORT_FOR_TRB(p) (((p) & 1) << 23)
+#define TRB_TO_SUSPEND_PORT(p) (((p) >> 23) & 0x1)
+#define LAST_EP_INDEX 30
+
+/* Set TR Dequeue Pointer command TRB fields. */
+#define TRB_TO_STREAM_ID(p) ((((p) & GENMASK(31, 16)) >> 16))
+#define STREAM_ID_FOR_TRB(p) ((((p)) << 16) & GENMASK(31, 16))
+#define SCT_FOR_TRB(p) (((p) << 1) & 0x7)
+
+/* Link TRB specific fields. */
+#define TRB_TC BIT(1)
+
+/* Port Status Change Event TRB fields. */
+/* Port ID - bits 31:24. */
+#define GET_PORT_ID(p) (((p) & GENMASK(31, 24)) >> 24)
+#define SET_PORT_ID(p) (((p) << 24) & GENMASK(31, 24))
+#define EVENT_DATA BIT(2)
+
+/* Normal TRB fields. */
+/* transfer_len bitmasks - bits 0:16. */
+#define TRB_LEN(p) ((p) & GENMASK(16, 0))
+/* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31). */
+#define TRB_TD_SIZE(p) (min((p), (u32)31) << 17)
+#define GET_TD_SIZE(p) (((p) & GENMASK(21, 17)) >> 17)
+/*
+ * Controller uses the TD_SIZE field for TBC if Extended TBC
+ * is enabled (ETE).
+ */
+#define TRB_TD_SIZE_TBC(p) (min((p), (u32)31) << 17)
+/* Interrupter Target - which MSI-X vector to target the completion event at. */
+#define TRB_INTR_TARGET(p) (((p) << 22) & GENMASK(31, 22))
+#define GET_INTR_TARGET(p) (((p) & GENMASK(31, 22)) >> 22)
+/*
+ * Total burst count field, Rsvdz on controller with Extended TBC
+ * enabled (ETE).
+ */
+#define TRB_TBC(p) (((p) & 0x3) << 7)
+#define TRB_TLBPC(p) (((p) & 0xf) << 16)
+
+/* Cycle bit - indicates TRB ownership by driver or driver.*/
+#define TRB_CYCLE BIT(0)
+/*
+ * Force next event data TRB to be evaluated before task switch.
+ * Used to pass OS data back after a TD completes.
+ */
+#define TRB_ENT BIT(1)
+/* Interrupt on short packet. */
+#define TRB_ISP BIT(2)
+/* Set PCIe no snoop attribute. */
+#define TRB_NO_SNOOP BIT(3)
+/* Chain multiple TRBs into a TD. */
+#define TRB_CHAIN BIT(4)
+/* Interrupt on completion. */
+#define TRB_IOC BIT(5)
+/* The buffer pointer contains immediate data. */
+#define TRB_IDT BIT(6)
+/* 0 - NRDY during data stage, 1 - NRDY during status stage (only control). */
+#define TRB_STAT BIT(7)
+/* Block Event Interrupt. */
+#define TRB_BEI BIT(9)
+
+/* Control transfer TRB specific fields. */
+#define TRB_DIR_IN BIT(16)
+
+/* TRB bit mask in Data Stage TRB */
+#define TRB_SETUPID_BITMASK GENMASK(9, 8)
+#define TRB_SETUPID(p) ((p) << 8)
+#define TRB_SETUPID_TO_TYPE(p) (((p) & TRB_SETUPID_BITMASK) >> 8)
+
+#define TRB_SETUP_SPEEDID_USB3 0x1
+#define TRB_SETUP_SPEEDID_USB2 0x0
+#define TRB_SETUP_SPEEDID(p) ((p) & (1 << 7))
+
+#define TRB_SETUPSTAT_ACK 0x1
+#define TRB_SETUPSTAT_STALL 0x0
+#define TRB_SETUPSTAT(p) ((p) << 6)
+
+/* Isochronous TRB specific fields */
+#define TRB_SIA BIT(31)
+#define TRB_FRAME_ID(p) (((p) << 20) & GENMASK(30, 20))
+
+struct cdnsp_generic_trb {
+ __le32 field[4];
+};
+
+union cdnsp_trb {
+ struct cdnsp_link_trb link;
+ struct cdnsp_transfer_event trans_event;
+ struct cdnsp_event_cmd event_cmd;
+ struct cdnsp_generic_trb generic;
+};
+
+/* TRB bit mask. */
+#define TRB_TYPE_BITMASK GENMASK(15, 10)
+#define TRB_TYPE(p) ((p) << 10)
+#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
+
+/* TRB type IDs. */
+/* bulk, interrupt, isoc scatter/gather, and control data stage. */
+#define TRB_NORMAL 1
+/* Setup Stage for control transfers. */
+#define TRB_SETUP 2
+/* Data Stage for control transfers. */
+#define TRB_DATA 3
+/* Status Stage for control transfers. */
+#define TRB_STATUS 4
+/* ISOC transfers. */
+#define TRB_ISOC 5
+/* TRB for linking ring segments. */
+#define TRB_LINK 6
+#define TRB_EVENT_DATA 7
+/* Transfer Ring No-op (not for the command ring). */
+#define TRB_TR_NOOP 8
+
+/* Command TRBs */
+/* Enable Slot Command. */
+#define TRB_ENABLE_SLOT 9
+/* Disable Slot Command. */
+#define TRB_DISABLE_SLOT 10
+/* Address Device Command. */
+#define TRB_ADDR_DEV 11
+/* Configure Endpoint Command. */
+#define TRB_CONFIG_EP 12
+/* Evaluate Context Command. */
+#define TRB_EVAL_CONTEXT 13
+/* Reset Endpoint Command. */
+#define TRB_RESET_EP 14
+/* Stop Transfer Ring Command. */
+#define TRB_STOP_RING 15
+/* Set Transfer Ring Dequeue Pointer Command. */
+#define TRB_SET_DEQ 16
+/* Reset Device Command. */
+#define TRB_RESET_DEV 17
+/* Force Event Command (opt). */
+#define TRB_FORCE_EVENT 18
+/* Force Header Command - generate a transaction or link management packet. */
+#define TRB_FORCE_HEADER 22
+/* No-op Command - not for transfer rings. */
+#define TRB_CMD_NOOP 23
+/* TRB IDs 24-31 reserved. */
+
+/* Event TRBS. */
+/* Transfer Event. */
+#define TRB_TRANSFER 32
+/* Command Completion Event. */
+#define TRB_COMPLETION 33
+/* Port Status Change Event. */
+#define TRB_PORT_STATUS 34
+/* Device Controller Event. */
+#define TRB_HC_EVENT 37
+/* MFINDEX Wrap Event - microframe counter wrapped. */
+#define TRB_MFINDEX_WRAP 39
+/* TRB IDs 40-47 reserved. */
+/* Endpoint Not Ready Event. */
+#define TRB_ENDPOINT_NRDY 48
+/* TRB IDs 49-53 reserved. */
+/* Halt Endpoint Command. */
+#define TRB_HALT_ENDPOINT 54
+/* Doorbell Overflow Event. */
+#define TRB_DRB_OVERFLOW 57
+/* Flush Endpoint Command. */
+#define TRB_FLUSH_ENDPOINT 58
+
+#define TRB_TYPE_LINK(x) (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK))
+#define TRB_TYPE_LINK_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
+ cpu_to_le32(TRB_TYPE(TRB_LINK)))
+#define TRB_TYPE_NOOP_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
+ cpu_to_le32(TRB_TYPE(TRB_TR_NOOP)))
+
+/*
+ * TRBS_PER_SEGMENT must be a multiple of 4.
+ * The command ring is 64-byte aligned, so it must also be greater than 16.
+ */
+#define TRBS_PER_SEGMENT 256
+#define TRBS_PER_EVENT_SEGMENT 256
+#define TRBS_PER_EV_DEQ_UPDATE 100
+#define TRB_SEGMENT_SIZE (TRBS_PER_SEGMENT * 16)
+#define TRB_SEGMENT_SHIFT (ilog2(TRB_SEGMENT_SIZE))
+/* TRB buffer pointers can't cross 64KB boundaries. */
+#define TRB_MAX_BUFF_SHIFT 16
+#define TRB_MAX_BUFF_SIZE BIT(TRB_MAX_BUFF_SHIFT)
+/* How much data is left before the 64KB boundary? */
+#define TRB_BUFF_LEN_UP_TO_BOUNDARY(addr) (TRB_MAX_BUFF_SIZE - \
+ ((addr) & (TRB_MAX_BUFF_SIZE - 1)))
+
+/**
+ * struct cdnsp_segment - segment related data.
+ * @trbs: Array of Transfer Request Blocks.
+ * @next: Pointer to the next segment.
+ * @dma: DMA address of current segment.
+ * @bounce_dma: Bounce buffer DMA address .
+ * @bounce_buf: Bounce buffer virtual address.
+ * bounce_offs: Bounce buffer offset.
+ * bounce_len: Bounce buffer length.
+ */
+struct cdnsp_segment {
+ union cdnsp_trb *trbs;
+ struct cdnsp_segment *next;
+ dma_addr_t dma;
+ /* Max packet sized bounce buffer for td-fragmant alignment */
+ dma_addr_t bounce_dma;
+ void *bounce_buf;
+ unsigned int bounce_offs;
+ unsigned int bounce_len;
+};
+
+/**
+ * struct cdnsp_td - Transfer Descriptor object.
+ * @td_list: Used for binding TD with ep_ring->td_list.
+ * @preq: Request associated with this TD
+ * @start_seg: Segment containing the first_trb in TD.
+ * @first_trb: First TRB for this TD.
+ * @last_trb: Last TRB related with TD.
+ * @bounce_seg: Bounce segment for this TD.
+ * @request_length_set: actual_length of the request has already been set.
+ * @drbl - TD has been added to HW scheduler - only for stream capable
+ * endpoints.
+ */
+struct cdnsp_td {
+ struct list_head td_list;
+ struct cdnsp_request *preq;
+ struct cdnsp_segment *start_seg;
+ union cdnsp_trb *first_trb;
+ union cdnsp_trb *last_trb;
+ struct cdnsp_segment *bounce_seg;
+ bool request_length_set;
+ bool drbl;
+};
+
+/**
+ * struct cdnsp_dequeue_state - New dequeue pointer for Transfer Ring.
+ * @new_deq_seg: New dequeue segment.
+ * @new_deq_ptr: New dequeue pointer.
+ * @new_cycle_state: New cycle state.
+ * @stream_id: stream id for which new dequeue pointer has been selected.
+ */
+struct cdnsp_dequeue_state {
+ struct cdnsp_segment *new_deq_seg;
+ union cdnsp_trb *new_deq_ptr;
+ int new_cycle_state;
+ unsigned int stream_id;
+};
+
+enum cdnsp_ring_type {
+ TYPE_CTRL = 0,
+ TYPE_ISOC,
+ TYPE_BULK,
+ TYPE_INTR,
+ TYPE_STREAM,
+ TYPE_COMMAND,
+ TYPE_EVENT,
+};
+
+/**
+ * struct cdnsp_ring - information describing transfer, command or event ring.
+ * @first_seg: First segment on transfer ring.
+ * @last_seg: Last segment on transfer ring.
+ * @enqueue: SW enqueue pointer address.
+ * @enq_seg: SW enqueue segment address.
+ * @dequeue: SW dequeue pointer address.
+ * @deq_seg: SW dequeue segment address.
+ * @td_list: transfer descriptor list associated with this ring.
+ * @cycle_state: Current cycle bit. Write the cycle state into the TRB cycle
+ * field to give ownership of the TRB to the device controller
+ * (if we are the producer) or to check if we own the TRB
+ * (if we are the consumer).
+ * @stream_id: Stream id
+ * @stream_active: Stream is active - PRIME packet has been detected.
+ * @stream_rejected: This ring has been rejected by host.
+ * @num_tds: Number of TDs associated with ring.
+ * @num_segs: Number of segments.
+ * @num_trbs_free: Number of free TRBs on the ring.
+ * @bounce_buf_len: Length of bounce buffer.
+ * @type: Ring type - event, transfer, or command ring.
+ * @last_td_was_short - TD is short TD.
+ * @trb_address_map: For mapping physical TRB addresses to segments in
+ * stream rings.
+ */
+struct cdnsp_ring {
+ struct cdnsp_segment *first_seg;
+ struct cdnsp_segment *last_seg;
+ union cdnsp_trb *enqueue;
+ struct cdnsp_segment *enq_seg;
+ union cdnsp_trb *dequeue;
+ struct cdnsp_segment *deq_seg;
+ struct list_head td_list;
+ u32 cycle_state;
+ unsigned int stream_id;
+ unsigned int stream_active;
+ unsigned int stream_rejected;
+ int num_tds;
+ unsigned int num_segs;
+ unsigned int num_trbs_free;
+ unsigned int bounce_buf_len;
+ enum cdnsp_ring_type type;
+ bool last_td_was_short;
+ struct radix_tree_root *trb_address_map;
+};
+
+/**
+ * struct cdnsp_erst_entry - even ring segment table entry object.
+ * @seg_addr: 64-bit event ring segment address.
+ * seg_size: Number of TRBs in segment.;
+ */
+struct cdnsp_erst_entry {
+ __le64 seg_addr;
+ __le32 seg_size;
+ /* Set to zero */
+ __le32 rsvd;
+};
+
+/**
+ * struct cdnsp_erst - even ring segment table for event ring.
+ * @entries: Array of event ring segments
+ * @num_entries: Number of segments in entries array.
+ * @erst_dma_addr: DMA address for entries array.
+ */
+struct cdnsp_erst {
+ struct cdnsp_erst_entry *entries;
+ unsigned int num_entries;
+ dma_addr_t erst_dma_addr;
+};
+
+/**
+ * struct cdnsp_request - extended device side representation of usb_request
+ * object .
+ * @td: Transfer descriptor associated with this request.
+ * @request: Generic usb_request object describing single I/O request.
+ * @list: Used to adding request to endpoint pending_list.
+ * @pep: Extended representation of usb_ep object
+ * @epnum: Endpoint number associated with usb request.
+ * @direction: Endpoint direction for usb request.
+ */
+struct cdnsp_request {
+ struct cdnsp_td td;
+ struct usb_request request;
+ struct list_head list;
+ struct cdnsp_ep *pep;
+ u8 epnum;
+ unsigned direction:1;
+};
+
+#define ERST_NUM_SEGS 1
+
+/* Stages used during enumeration process.*/
+enum cdnsp_ep0_stage {
+ CDNSP_SETUP_STAGE,
+ CDNSP_DATA_STAGE,
+ CDNSP_STATUS_STAGE,
+};
+
+/**
+ * struct cdnsp_port - holds information about detected ports.
+ * @port_num: Port number.
+ * @exist: Indicate if port exist.
+ * maj_rev: Major revision.
+ * min_rev: Minor revision.
+ */
+struct cdnsp_port {
+ struct cdnsp_port_regs __iomem *regs;
+ u8 port_num;
+ u8 exist;
+ u8 maj_rev;
+ u8 min_rev;
+};
+
+#define CDNSP_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff)
+#define CDNSP_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff)
+#define CDNSP_EXT_PORT_OFF(x) ((x) & 0xff)
+#define CDNSP_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff)
+
+/**
+ * struct cdnsp_device - represent USB device.
+ * @dev: Pointer to device structure associated whit this controller.
+ * @gadget: Device side representation of the peripheral controller.
+ * @gadget_driver: Pointer to the gadget driver.
+ * @irq: IRQ line number used by device side.
+ * @regs:IO device memory.
+ * @cap_regs: Capability registers.
+ * @op_regs: Operational registers.
+ * @run_regs: Runtime registers.
+ * @dba: Device base address register.
+ * @ir_set: Current interrupter register set.
+ * @port20_regs: Port 2.0 Peripheral Configuration Registers.
+ * @port3x_regs: USB3.x Port Peripheral Configuration Registers.
+ * @hcs_params1: Cached register copies of read-only HCSPARAMS1
+ * @hcc_params: Cached register copies of read-only HCCPARAMS1
+ * @rev_cap: Controller capability.
+ * @setup: Temporary buffer for setup packet.
+ * @ep0_preq: Internal allocated request used during enumeration.
+ * @ep0_stage: ep0 stage during enumeration process.
+ * @three_stage_setup: Three state or two state setup.
+ * @ep0_expect_in: Data IN expected for control transfer.
+ * @setup_id: Setup identifier.
+ * @setup_speed - Speed detected for current SETUP packet.
+ * @setup_buf: Buffer for SETUP packet.
+ * @device_address: Current device address.
+ * @may_wakeup: remote wakeup enabled/disabled.
+ * @lock: Lock used in interrupt thread context.
+ * @hci_version: device controller version.
+ * @dcbaa: Device context base address array.
+ * @cmd_ring: Command ring.
+ * @cmd: Represent all what is needed to issue command on Command Ring.
+ * @event_ring: Event ring.
+ * @erst: Event Ring Segment table
+ * @slot_id: Current Slot ID. Should be 0 or 1.
+ * @out_ctx: Output context.
+ * @in_ctx: Input context.
+ * @eps: array of endpoints object associated with device.
+ * @usb2_hw_lpm_capable: hardware lpm is enabled;
+ * @u1_allowed: Allow device transition to U1 state.
+ * @u2_allowed: Allow device transition to U2 state
+ * @device_pool: DMA pool for allocating input and output context.
+ * @segment_pool: DMA pool for allocating new segments.
+ * @cdnsp_state: Current state of controller.
+ * @link_state: Current link state.
+ * @usb2_port - Port USB 2.0.
+ * @usb3_port - Port USB 3.0.
+ * @active_port - Current selected Port.
+ * @test_mode: selected Test Mode.
+ */
+struct cdnsp_device {
+ struct device *dev;
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *gadget_driver;
+ unsigned int irq;
+ void __iomem *regs;
+
+ /* Registers map */
+ struct cdnsp_cap_regs __iomem *cap_regs;
+ struct cdnsp_op_regs __iomem *op_regs;
+ struct cdnsp_run_regs __iomem *run_regs;
+ struct cdnsp_doorbell_array __iomem *dba;
+ struct cdnsp_intr_reg __iomem *ir_set;
+ struct cdnsp_20port_cap __iomem *port20_regs;
+ struct cdnsp_3xport_cap __iomem *port3x_regs;
+
+ /* Cached register copies of read-only CDNSP data */
+ __u32 hcs_params1;
+ __u32 hcs_params3;
+ __u32 hcc_params;
+ struct cdnsp_rev_cap rev_cap;
+ /* Lock used in interrupt thread context. */
+ spinlock_t lock;
+ struct usb_ctrlrequest setup;
+ struct cdnsp_request ep0_preq;
+ enum cdnsp_ep0_stage ep0_stage;
+ u8 three_stage_setup;
+ u8 ep0_expect_in;
+ u8 setup_id;
+ u8 setup_speed;
+ void *setup_buf;
+ u8 device_address;
+ int may_wakeup;
+ u16 hci_version;
+
+ /* data structures */
+ struct cdnsp_device_context_array *dcbaa;
+ struct cdnsp_ring *cmd_ring;
+ struct cdnsp_command cmd;
+ struct cdnsp_ring *event_ring;
+ struct cdnsp_erst erst;
+ int slot_id;
+
+ /*
+ * Commands to the hardware are passed an "input context" that
+ * tells the hardware what to change in its data structures.
+ * The hardware will return changes in an "output context" that
+ * software must allocate for the hardware. .
+ */
+ struct cdnsp_container_ctx out_ctx;
+ struct cdnsp_container_ctx in_ctx;
+ struct cdnsp_ep eps[CDNSP_ENDPOINTS_NUM];
+ u8 usb2_hw_lpm_capable:1;
+ u8 u1_allowed:1;
+ u8 u2_allowed:1;
+
+ /* DMA pools */
+ struct dma_pool *device_pool;
+ struct dma_pool *segment_pool;
+
+#define CDNSP_STATE_HALTED BIT(1)
+#define CDNSP_STATE_DYING BIT(2)
+#define CDNSP_STATE_DISCONNECT_PENDING BIT(3)
+#define CDNSP_WAKEUP_PENDING BIT(4)
+ unsigned int cdnsp_state;
+ unsigned int link_state;
+
+ struct cdnsp_port usb2_port;
+ struct cdnsp_port usb3_port;
+ struct cdnsp_port *active_port;
+ u16 test_mode;
+};
+
+#endif /* __LINUX_CDNSP_GADGET_H */
Patch defines macros, registers and structures used by Device side driver. Because the size of main patch is very big, I’ve decided to create separate patch for cdnsp-gadget.h. It should simplify reviewing the code. Signed-off-by: Pawel Laszczak <pawell@cadence.com> --- drivers/usb/cdns3/cdnsp-gadget.h | 1463 ++++++++++++++++++++++++++++++ 1 file changed, 1463 insertions(+) create mode 100644 drivers/usb/cdns3/cdnsp-gadget.h