| Message ID | 20220421162158.31364-1-jmaselbas@kalray.eu (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [RFC] phy: Convert usb-nop-xceiv to the generic phy subsystem | expand |
Hi Jules, On 4/21/22 12:21 PM, Jules Maselbas wrote: > I recently encountered some limitations when using the usb-nop-xceiv > driver using the usb-phy subsystem. The situation is: I have a board > with two external usb phys (ULPI) that only needs to be reset by the > USB controller. However both phys shares the same reset line, which > will get toggled twice by the USB driver, once by controller. > > This is what I observed with the current Linux usb-nop-xceiv driver: > _______ ___ _________ > RESET: \__________________________/ \____/ > 1^ 2^ 3^ 4^ > 1. and 2. first controller toggle the reset > 3. and 4. second controller toggle the reset > > After the second toggle the first driver didn't expected the reset and > causing issues, but I don't recall what exactly, it is maybe a driver > that simply fail to get probed. Ah, a tale as old as GPIO resets... (c.f. MDIO) > The following is what I observed when using the "usb-nop-xceiv" > driver in Barebox, which is a bit different than the Linux one. > > _______ _________________ > RESET: \__________________________/ > 1^ 2^ > > In this case the reset is only toggled once, this is because the phy > driver count the number of time it has called init and power_on, which > is exactly what is done by the generic phy subsystem in Linux, but not > by the "legacy" usb-nop-xceiv usb-phy driver. Can you provide a snippet of your device tree? I am not quite sure how you are describing your phys. Do you use the same device for multiple USBs? > This difference in behavior is what motivated to "port" the existing > usb-nop-xceiv driver to the generic phy subsystem. However this is far > from being complete... I've only tested the reset function for this nop > phy, and it lack a lot of features from the original driver to be a > valid replacement for it. > > I would like to know if there is an interest in converting the current > usb-nop-xceiv driver to the generic phy subsystem? > > I would like to keep the usb-nop-xceiv compatible as it used by Barebox > and it works OK. If a new compatible is added then device-tree nodes > shouldn't have both, the new and usb-nop-xceiv, compatible because of > the specific check in phy-core.c which will always return ENODEV. > > Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu> > --- > drivers/phy/Makefile | 1 + > drivers/phy/phy-core.c | 4 - > drivers/phy/phy-usb-generic.c | 241 ++++++++++++++++++++++++++++++++++ > 3 files changed, 242 insertions(+), 4 deletions(-) > create mode 100644 drivers/phy/phy-usb-generic.c Since this is a conversion, I would expect that the old driver would be deleted. In particular, the Kconfig will need to be adjusted so that users of the old driver will have CONFIG_GENERIC_PHY enabled (and some reimplementation of usb_phy_gen_create_phy). I think we would still need to call usb_add_phy_dev in probe() as well. Though I suppose this is why this patch is RFC? > > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > index 6eb2916773c5..8eeecf6d6f74 100644 > --- a/drivers/phy/Makefile > +++ b/drivers/phy/Makefile > @@ -4,6 +4,7 @@ > # > > obj-$(CONFIG_GENERIC_PHY) += phy-core.o > +obj-$(CONFIG_GENERIC_PHY) += phy-usb-generic.o > obj-$(CONFIG_GENERIC_PHY_MIPI_DPHY) += phy-core-mipi-dphy.o > obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o > obj-$(CONFIG_PHY_XGENE) += phy-xgene.o > diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c > index 71cb10826326..e09fd1cb4455 100644 > --- a/drivers/phy/phy-core.c > +++ b/drivers/phy/phy-core.c > @@ -506,10 +506,6 @@ static struct phy *_of_phy_get(struct device_node *np, int index) > if (ret) > return ERR_PTR(-ENODEV); > > - /* This phy type handled by the usb-phy subsystem for now */ > - if (of_device_is_compatible(args.np, "usb-nop-xceiv")) > - return ERR_PTR(-ENODEV); > - > mutex_lock(&phy_provider_mutex); > phy_provider = of_phy_provider_lookup(args.np); > if (IS_ERR(phy_provider) || !try_module_get(phy_provider->owner)) { > diff --git a/drivers/phy/phy-usb-generic.c b/drivers/phy/phy-usb-generic.c > new file mode 100644 > index 000000000000..fdd05bbd98f2 > --- /dev/null > +++ b/drivers/phy/phy-usb-generic.c > @@ -0,0 +1,241 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * derived from driver/usb/phy/phy-generic.c > + * > + * Generic USB PHY driver for all USB "nop" transceiver which are mostly > + * autonomous. This driver is derived from the usb-nop-xceiv driver, but > + * this one use the new generic phy api. > + * > + * Copyright (c) 2022 Kalray Inc. > + * Author(s): Jules Maselbas > + */ > + > +#include <linux/clk.h> > +#include <linux/err.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/phy/phy.h> > +#include <linux/platform_device.h> > +#include <linux/regulator/consumer.h> > +#include <linux/gpio/consumer.h> > +#include <linux/delay.h> > +#include <linux/usb/otg.h> > + > +struct phy_usb_generic { > + struct device *dev; > + struct clk *clk; > + struct regulator *vcc; > + struct gpio_desc *gpiod_reset; > + unsigned long mA; > + unsigned int vbus; These are unused > + enum usb_dr_mode dr_mode; > +}; > + > +static int phy_usb_generic_init(struct phy *phy) > +{ > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > + > + if (priv->clk) > + clk_prepare(priv->clk); > + > + return 0; > +} > + > +static int phy_usb_generic_exit(struct phy *phy) > +{ > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > + > + if (priv->clk) > + clk_unprepare(priv->clk); > + > + return 0; > +} > + > +static int phy_usb_generic_power_on(struct phy *phy) > +{ > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > + int ret; > + > + if (priv->vcc) { > + ret = regulator_enable(priv->vcc); > + if (ret) { > + dev_err(priv->dev, "Failed to enable power\n"); > + return ret; > + } > + } > + > + if (priv->clk) { > + ret = clk_enable(priv->clk); > + if (ret) { > + dev_err(priv->dev, "Failed to enable clock\n"); > + return ret; > + } > + } > + > + if (priv->gpiod_reset) { > + dev_dbg(priv->dev, "Reset toggle\n"); > + gpiod_set_value_cansleep(priv->gpiod_reset, 1); > + usleep_range(10000, 20000); > + gpiod_set_value_cansleep(priv->gpiod_reset, 0); > + } > + > + return 0; > +} > + > +static int phy_usb_generic_power_off(struct phy *phy) > +{ > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > + int ret; > + > + if (priv->gpiod_reset) > + gpiod_set_value_cansleep(priv->gpiod_reset, 1); > + > + if (priv->clk) > + clk_disable_unprepare(priv->clk); > + > + if (priv->vcc) { > + ret = regulator_disable(priv->vcc); > + if (ret) { > + dev_err(priv->dev, "Failed to disable power\n"); > + return ret; > + } > + } > + > + return 0; > +} > + > +static int phy_usb_generic_set_mode(struct phy *phy, > + enum phy_mode mode, int submode) > +{ > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > + enum usb_dr_mode new_mode; > + const char *s = ""; > + > + switch (mode) { > + case PHY_MODE_USB_HOST: > + case PHY_MODE_USB_HOST_LS: > + case PHY_MODE_USB_HOST_HS: > + case PHY_MODE_USB_HOST_FS: > + new_mode = USB_DR_MODE_HOST; > + s = "host"; > + break; > + case PHY_MODE_USB_DEVICE: > + case PHY_MODE_USB_DEVICE_LS: > + case PHY_MODE_USB_DEVICE_HS: > + case PHY_MODE_USB_DEVICE_FS: > + new_mode = USB_DR_MODE_PERIPHERAL; > + s = "peripheral"; > + break; > + case PHY_MODE_USB_OTG: > + new_mode = USB_DR_MODE_OTG; > + s = "otg"; > + break; > + default: > + return -EINVAL; > + } > + > + if (new_mode != priv->dr_mode) { > + dev_info(priv->dev, "Changing dr_mode to %s\n", s); > + priv->dr_mode = new_mode; > + } > + > + return 0; > +} > + > +static const struct phy_ops phy_usb_generic_ops = { > + .init = phy_usb_generic_init, > + .exit = phy_usb_generic_exit, > + .power_on = phy_usb_generic_power_on, > + .power_off = phy_usb_generic_power_off, > + .set_mode = phy_usb_generic_set_mode, > + .owner = THIS_MODULE, > +}; > + > +static int phy_usb_generic_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct device_node *np = dev->of_node; > + struct phy_usb_generic *priv; > + struct phy_provider *provider; > + struct phy *phy; > + int err; > + u32 clk_rate = 0; > + > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + priv->dev = &pdev->dev; > + platform_set_drvdata(pdev, priv); > + > + priv->gpiod_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_ASIS); > + if (IS_ERR(priv->gpiod_reset)) { > + err = PTR_ERR(priv->gpiod_reset); > + dev_err(dev, "Failed to get reset gpio: %d\n", err); These should be dev_err_probe to avoid noise when we get -EPROBE_DEFER. Ditto for the rest of the dev_errs. > + return err; > + } > + > + if (np && of_property_read_u32(np, "clock-frequency", &clk_rate)) > + clk_rate = 0; > + > + priv->clk = devm_clk_get_optional(dev, "main_clk"); > + if (IS_ERR(priv->clk)) { > + err = PTR_ERR(priv->clk); > + dev_err(dev, "Can't get phy clock: %d\n", err); > + return err; > + } > + if (priv->clk && clk_rate) { > + err = clk_set_rate(priv->clk, clk_rate); > + if (err) { > + dev_err(dev, "Error setting clock rate\n"); > + return err; > + } > + } > + > + priv->vcc = devm_regulator_get_optional(dev, "vcc"); > + if (IS_ERR(priv->vcc)) { > + err = PTR_ERR(priv->vcc); > + if (err == -ENODEV || err == -ENOENT) { > + priv->vcc = NULL; > + } else { > + dev_err(dev, "Error getting vcc regulator: %d\n", err); > + return err; > + } > + } > + > + phy = devm_phy_create(dev, NULL, &phy_usb_generic_ops); > + if (IS_ERR(phy)) { > + err = PTR_ERR(phy); > + dev_err(dev, "Failed to create PHY: %d\n", err); > + return err; > + } > + phy_set_drvdata(phy, priv); > + > + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); > + if (IS_ERR(provider)) { > + err = PTR_ERR(provider); > + dev_err(dev, "Failed to register PHY provider: %d\n", err); > + return err; > + } > + > + return 0; > +} > + > +static const struct of_device_id phy_usb_nop_dt_ids[] = { > + { .compatible = "phy-usb-generic" }, > + { .compatible = "usb-nop-xceiv" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, phy_usb_nop_dt_ids); > + > +static struct platform_driver phy_usb_generic_driver = { > + .probe = phy_usb_generic_probe, > + .driver = { > + .name = "phy_usb_generic", > + .of_match_table = phy_usb_nop_dt_ids, > + }, > +}; > +module_platform_driver(phy_usb_generic_driver); > + > +MODULE_AUTHOR("Kalray Inc"); > +MODULE_DESCRIPTION("Generic USB PHY driver"); > +MODULE_LICENSE("GPL"); > The rest looks good (modulo missing features). --Sean
On Mon, Apr 25, 2022 at 01:01:10PM -0400, Sean Anderson wrote: > Hi Jules, > > On 4/21/22 12:21 PM, Jules Maselbas wrote: > > I recently encountered some limitations when using the usb-nop-xceiv > > driver using the usb-phy subsystem. The situation is: I have a board > > with two external usb phys (ULPI) that only needs to be reset by the > > USB controller. However both phys shares the same reset line, which > > will get toggled twice by the USB driver, once by controller. > > > > This is what I observed with the current Linux usb-nop-xceiv driver: > > _______ ___ _________ > > RESET: \__________________________/ \____/ > > 1^ 2^ 3^ 4^ > > 1. and 2. first controller toggle the reset > > 3. and 4. second controller toggle the reset > > > > After the second toggle the first driver didn't expected the reset and > > causing issues, but I don't recall what exactly, it is maybe a driver > > that simply fail to get probed. > > Ah, a tale as old as GPIO resets... (c.f. MDIO) I didn't get it :] > > > The following is what I observed when using the "usb-nop-xceiv" > > driver in Barebox, which is a bit different than the Linux one. > > > > _______ _________________ > > RESET: \__________________________/ > > 1^ 2^ > > > > In this case the reset is only toggled once, this is because the phy > > driver count the number of time it has called init and power_on, which > > is exactly what is done by the generic phy subsystem in Linux, but not > > by the "legacy" usb-nop-xceiv usb-phy driver. > > Can you provide a snippet of your device tree? I am not quite sure how > you are describing your phys. Do you use the same device for multiple USBs? Yes I use the same phy "device" for multiple USBs, like so: / { usb_phy0: usb-phy0 { #phy-cells = <0>; compatible = "usb-nop-xceiv"; reset-gpios = <&gpio1_banka 21 GPIO_ACTIVE_LOW>; }; }; &usb0 { dr_mode = "peripheral"; phys = <&usb_phy0>; phy-names = "usb2-phy"; }; &usb1 { phys = <&usb_phy0>; phy-names = "usb2-phy"; }; > > > This difference in behavior is what motivated to "port" the existing > > usb-nop-xceiv driver to the generic phy subsystem. However this is far > > from being complete... I've only tested the reset function for this nop > > phy, and it lack a lot of features from the original driver to be a > > valid replacement for it. > > > > I would like to know if there is an interest in converting the current > > usb-nop-xceiv driver to the generic phy subsystem? > > > > I would like to keep the usb-nop-xceiv compatible as it used by Barebox > > and it works OK. If a new compatible is added then device-tree nodes > > shouldn't have both, the new and usb-nop-xceiv, compatible because of > > the specific check in phy-core.c which will always return ENODEV. > > > > Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu> > > --- > > drivers/phy/Makefile | 1 + > > drivers/phy/phy-core.c | 4 - > > drivers/phy/phy-usb-generic.c | 241 ++++++++++++++++++++++++++++++++++ > > 3 files changed, 242 insertions(+), 4 deletions(-) > > create mode 100644 drivers/phy/phy-usb-generic.c > > Since this is a conversion, I would expect that the old driver would be > deleted. In particular, the Kconfig will need to be adjusted so that > users of the old driver will have CONFIG_GENERIC_PHY enabled (and some > reimplementation of usb_phy_gen_create_phy). I think we would still need Of course, if this is a conversion i would also remove the old driver, but I didn't wanted to cluter the diff... this is very much an RFC, asking for advices. > to call usb_add_phy_dev in probe() as well. Ok, I'll look into that. > Though I suppose this is why this patch is RFC? Yes, this is why. > > > > > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > > index 6eb2916773c5..8eeecf6d6f74 100644 > > --- a/drivers/phy/Makefile > > +++ b/drivers/phy/Makefile > > @@ -4,6 +4,7 @@ > > # > > > > obj-$(CONFIG_GENERIC_PHY) += phy-core.o > > +obj-$(CONFIG_GENERIC_PHY) += phy-usb-generic.o > > obj-$(CONFIG_GENERIC_PHY_MIPI_DPHY) += phy-core-mipi-dphy.o > > obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o > > obj-$(CONFIG_PHY_XGENE) += phy-xgene.o > > diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c > > index 71cb10826326..e09fd1cb4455 100644 > > --- a/drivers/phy/phy-core.c > > +++ b/drivers/phy/phy-core.c > > @@ -506,10 +506,6 @@ static struct phy *_of_phy_get(struct device_node *np, int index) > > if (ret) > > return ERR_PTR(-ENODEV); > > > > - /* This phy type handled by the usb-phy subsystem for now */ > > - if (of_device_is_compatible(args.np, "usb-nop-xceiv")) > > - return ERR_PTR(-ENODEV); > > - > > mutex_lock(&phy_provider_mutex); > > phy_provider = of_phy_provider_lookup(args.np); > > if (IS_ERR(phy_provider) || !try_module_get(phy_provider->owner)) { > > diff --git a/drivers/phy/phy-usb-generic.c b/drivers/phy/phy-usb-generic.c > > new file mode 100644 > > index 000000000000..fdd05bbd98f2 > > --- /dev/null > > +++ b/drivers/phy/phy-usb-generic.c > > @@ -0,0 +1,241 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later > > +/* > > + * derived from driver/usb/phy/phy-generic.c > > + * > > + * Generic USB PHY driver for all USB "nop" transceiver which are mostly > > + * autonomous. This driver is derived from the usb-nop-xceiv driver, but > > + * this one use the new generic phy api. > > + * > > + * Copyright (c) 2022 Kalray Inc. > > + * Author(s): Jules Maselbas > > + */ > > + > > +#include <linux/clk.h> > > +#include <linux/err.h> > > +#include <linux/module.h> > > +#include <linux/of.h> > > +#include <linux/phy/phy.h> > > +#include <linux/platform_device.h> > > +#include <linux/regulator/consumer.h> > > +#include <linux/gpio/consumer.h> > > +#include <linux/delay.h> > > +#include <linux/usb/otg.h> > > + > > +struct phy_usb_generic { > > + struct device *dev; > > + struct clk *clk; > > + struct regulator *vcc; > > + struct gpio_desc *gpiod_reset; > > + unsigned long mA; > > + unsigned int vbus; > > These are unused Indeed > > + enum usb_dr_mode dr_mode; > > +}; > > + > > +static int phy_usb_generic_init(struct phy *phy) > > +{ > > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > > + > > + if (priv->clk) > > + clk_prepare(priv->clk); > > + > > + return 0; > > +} > > + > > +static int phy_usb_generic_exit(struct phy *phy) > > +{ > > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > > + > > + if (priv->clk) > > + clk_unprepare(priv->clk); > > + > > + return 0; > > +} > > + > > +static int phy_usb_generic_power_on(struct phy *phy) > > +{ > > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > > + int ret; > > + > > + if (priv->vcc) { > > + ret = regulator_enable(priv->vcc); > > + if (ret) { > > + dev_err(priv->dev, "Failed to enable power\n"); > > + return ret; > > + } > > + } > > + > > + if (priv->clk) { > > + ret = clk_enable(priv->clk); > > + if (ret) { > > + dev_err(priv->dev, "Failed to enable clock\n"); > > + return ret; > > + } > > + } > > + > > + if (priv->gpiod_reset) { > > + dev_dbg(priv->dev, "Reset toggle\n"); > > + gpiod_set_value_cansleep(priv->gpiod_reset, 1); > > + usleep_range(10000, 20000); > > + gpiod_set_value_cansleep(priv->gpiod_reset, 0); > > + } > > + > > + return 0; > > +} > > + > > +static int phy_usb_generic_power_off(struct phy *phy) > > +{ > > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > > + int ret; > > + > > + if (priv->gpiod_reset) > > + gpiod_set_value_cansleep(priv->gpiod_reset, 1); > > + > > + if (priv->clk) > > + clk_disable_unprepare(priv->clk); > > + > > + if (priv->vcc) { > > + ret = regulator_disable(priv->vcc); > > + if (ret) { > > + dev_err(priv->dev, "Failed to disable power\n"); > > + return ret; > > + } > > + } > > + > > + return 0; > > +} > > + > > +static int phy_usb_generic_set_mode(struct phy *phy, > > + enum phy_mode mode, int submode) > > +{ > > + struct phy_usb_generic *priv = phy_get_drvdata(phy); > > + enum usb_dr_mode new_mode; > > + const char *s = ""; > > + > > + switch (mode) { > > + case PHY_MODE_USB_HOST: > > + case PHY_MODE_USB_HOST_LS: > > + case PHY_MODE_USB_HOST_HS: > > + case PHY_MODE_USB_HOST_FS: > > + new_mode = USB_DR_MODE_HOST; > > + s = "host"; > > + break; > > + case PHY_MODE_USB_DEVICE: > > + case PHY_MODE_USB_DEVICE_LS: > > + case PHY_MODE_USB_DEVICE_HS: > > + case PHY_MODE_USB_DEVICE_FS: > > + new_mode = USB_DR_MODE_PERIPHERAL; > > + s = "peripheral"; > > + break; > > + case PHY_MODE_USB_OTG: > > + new_mode = USB_DR_MODE_OTG; > > + s = "otg"; > > + break; > > + default: > > + return -EINVAL; > > + } > > + > > + if (new_mode != priv->dr_mode) { > > + dev_info(priv->dev, "Changing dr_mode to %s\n", s); > > + priv->dr_mode = new_mode; > > + } > > + > > + return 0; > > +} > > + > > +static const struct phy_ops phy_usb_generic_ops = { > > + .init = phy_usb_generic_init, > > + .exit = phy_usb_generic_exit, > > + .power_on = phy_usb_generic_power_on, > > + .power_off = phy_usb_generic_power_off, > > + .set_mode = phy_usb_generic_set_mode, > > + .owner = THIS_MODULE, > > +}; > > + > > +static int phy_usb_generic_probe(struct platform_device *pdev) > > +{ > > + struct device *dev = &pdev->dev; > > + struct device_node *np = dev->of_node; > > + struct phy_usb_generic *priv; > > + struct phy_provider *provider; > > + struct phy *phy; > > + int err; > > + u32 clk_rate = 0; > > + > > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > > + if (!priv) > > + return -ENOMEM; > > + priv->dev = &pdev->dev; > > + platform_set_drvdata(pdev, priv); > > + > > + priv->gpiod_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_ASIS); > > + if (IS_ERR(priv->gpiod_reset)) { > > + err = PTR_ERR(priv->gpiod_reset); > > + dev_err(dev, "Failed to get reset gpio: %d\n", err); > > These should be dev_err_probe to avoid noise when we get -EPROBE_DEFER. Ditto > for the rest of the dev_errs. > Thanks, TIL dev_err_probe! I'll modify this > > + return err; > > + } > > + > > + if (np && of_property_read_u32(np, "clock-frequency", &clk_rate)) > > + clk_rate = 0; > > + > > + priv->clk = devm_clk_get_optional(dev, "main_clk"); > > + if (IS_ERR(priv->clk)) { > > + err = PTR_ERR(priv->clk); > > + dev_err(dev, "Can't get phy clock: %d\n", err); > > + return err; > > + } > > + if (priv->clk && clk_rate) { > > + err = clk_set_rate(priv->clk, clk_rate); > > + if (err) { > > + dev_err(dev, "Error setting clock rate\n"); > > + return err; > > + } > > + } > > + > > + priv->vcc = devm_regulator_get_optional(dev, "vcc"); > > + if (IS_ERR(priv->vcc)) { > > + err = PTR_ERR(priv->vcc); > > + if (err == -ENODEV || err == -ENOENT) { > > + priv->vcc = NULL; > > + } else { > > + dev_err(dev, "Error getting vcc regulator: %d\n", err); > > + return err; > > + } > > + } > > + > > + phy = devm_phy_create(dev, NULL, &phy_usb_generic_ops); > > + if (IS_ERR(phy)) { > > + err = PTR_ERR(phy); > > + dev_err(dev, "Failed to create PHY: %d\n", err); > > + return err; > > + } > > + phy_set_drvdata(phy, priv); > > + > > + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); > > + if (IS_ERR(provider)) { > > + err = PTR_ERR(provider); > > + dev_err(dev, "Failed to register PHY provider: %d\n", err); > > + return err; > > + } > > + > > + return 0; > > +} > > + > > +static const struct of_device_id phy_usb_nop_dt_ids[] = { > > + { .compatible = "phy-usb-generic" }, > > + { .compatible = "usb-nop-xceiv" }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(of, phy_usb_nop_dt_ids); > > + > > +static struct platform_driver phy_usb_generic_driver = { > > + .probe = phy_usb_generic_probe, > > + .driver = { > > + .name = "phy_usb_generic", > > + .of_match_table = phy_usb_nop_dt_ids, > > + }, > > +}; > > +module_platform_driver(phy_usb_generic_driver); > > + > > +MODULE_AUTHOR("Kalray Inc"); > > +MODULE_DESCRIPTION("Generic USB PHY driver"); > > +MODULE_LICENSE("GPL"); > > > > The rest looks good (modulo missing features). Yeah, I feel also there is a lot of missing features from the usb-nop-xceiv driver. I doesn't need much more than a simple gpio hence it is difficult for me to test porting other features. Thanks, -- Jules
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index 6eb2916773c5..8eeecf6d6f74 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -4,6 +4,7 @@ # obj-$(CONFIG_GENERIC_PHY) += phy-core.o +obj-$(CONFIG_GENERIC_PHY) += phy-usb-generic.o obj-$(CONFIG_GENERIC_PHY_MIPI_DPHY) += phy-core-mipi-dphy.o obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o obj-$(CONFIG_PHY_XGENE) += phy-xgene.o diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c index 71cb10826326..e09fd1cb4455 100644 --- a/drivers/phy/phy-core.c +++ b/drivers/phy/phy-core.c @@ -506,10 +506,6 @@ static struct phy *_of_phy_get(struct device_node *np, int index) if (ret) return ERR_PTR(-ENODEV); - /* This phy type handled by the usb-phy subsystem for now */ - if (of_device_is_compatible(args.np, "usb-nop-xceiv")) - return ERR_PTR(-ENODEV); - mutex_lock(&phy_provider_mutex); phy_provider = of_phy_provider_lookup(args.np); if (IS_ERR(phy_provider) || !try_module_get(phy_provider->owner)) { diff --git a/drivers/phy/phy-usb-generic.c b/drivers/phy/phy-usb-generic.c new file mode 100644 index 000000000000..fdd05bbd98f2 --- /dev/null +++ b/drivers/phy/phy-usb-generic.c @@ -0,0 +1,241 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * derived from driver/usb/phy/phy-generic.c + * + * Generic USB PHY driver for all USB "nop" transceiver which are mostly + * autonomous. This driver is derived from the usb-nop-xceiv driver, but + * this one use the new generic phy api. + * + * Copyright (c) 2022 Kalray Inc. + * Author(s): Jules Maselbas + */ + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/regulator/consumer.h> +#include <linux/gpio/consumer.h> +#include <linux/delay.h> +#include <linux/usb/otg.h> + +struct phy_usb_generic { + struct device *dev; + struct clk *clk; + struct regulator *vcc; + struct gpio_desc *gpiod_reset; + unsigned long mA; + unsigned int vbus; + enum usb_dr_mode dr_mode; +}; + +static int phy_usb_generic_init(struct phy *phy) +{ + struct phy_usb_generic *priv = phy_get_drvdata(phy); + + if (priv->clk) + clk_prepare(priv->clk); + + return 0; +} + +static int phy_usb_generic_exit(struct phy *phy) +{ + struct phy_usb_generic *priv = phy_get_drvdata(phy); + + if (priv->clk) + clk_unprepare(priv->clk); + + return 0; +} + +static int phy_usb_generic_power_on(struct phy *phy) +{ + struct phy_usb_generic *priv = phy_get_drvdata(phy); + int ret; + + if (priv->vcc) { + ret = regulator_enable(priv->vcc); + if (ret) { + dev_err(priv->dev, "Failed to enable power\n"); + return ret; + } + } + + if (priv->clk) { + ret = clk_enable(priv->clk); + if (ret) { + dev_err(priv->dev, "Failed to enable clock\n"); + return ret; + } + } + + if (priv->gpiod_reset) { + dev_dbg(priv->dev, "Reset toggle\n"); + gpiod_set_value_cansleep(priv->gpiod_reset, 1); + usleep_range(10000, 20000); + gpiod_set_value_cansleep(priv->gpiod_reset, 0); + } + + return 0; +} + +static int phy_usb_generic_power_off(struct phy *phy) +{ + struct phy_usb_generic *priv = phy_get_drvdata(phy); + int ret; + + if (priv->gpiod_reset) + gpiod_set_value_cansleep(priv->gpiod_reset, 1); + + if (priv->clk) + clk_disable_unprepare(priv->clk); + + if (priv->vcc) { + ret = regulator_disable(priv->vcc); + if (ret) { + dev_err(priv->dev, "Failed to disable power\n"); + return ret; + } + } + + return 0; +} + +static int phy_usb_generic_set_mode(struct phy *phy, + enum phy_mode mode, int submode) +{ + struct phy_usb_generic *priv = phy_get_drvdata(phy); + enum usb_dr_mode new_mode; + const char *s = ""; + + switch (mode) { + case PHY_MODE_USB_HOST: + case PHY_MODE_USB_HOST_LS: + case PHY_MODE_USB_HOST_HS: + case PHY_MODE_USB_HOST_FS: + new_mode = USB_DR_MODE_HOST; + s = "host"; + break; + case PHY_MODE_USB_DEVICE: + case PHY_MODE_USB_DEVICE_LS: + case PHY_MODE_USB_DEVICE_HS: + case PHY_MODE_USB_DEVICE_FS: + new_mode = USB_DR_MODE_PERIPHERAL; + s = "peripheral"; + break; + case PHY_MODE_USB_OTG: + new_mode = USB_DR_MODE_OTG; + s = "otg"; + break; + default: + return -EINVAL; + } + + if (new_mode != priv->dr_mode) { + dev_info(priv->dev, "Changing dr_mode to %s\n", s); + priv->dr_mode = new_mode; + } + + return 0; +} + +static const struct phy_ops phy_usb_generic_ops = { + .init = phy_usb_generic_init, + .exit = phy_usb_generic_exit, + .power_on = phy_usb_generic_power_on, + .power_off = phy_usb_generic_power_off, + .set_mode = phy_usb_generic_set_mode, + .owner = THIS_MODULE, +}; + +static int phy_usb_generic_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct phy_usb_generic *priv; + struct phy_provider *provider; + struct phy *phy; + int err; + u32 clk_rate = 0; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + priv->dev = &pdev->dev; + platform_set_drvdata(pdev, priv); + + priv->gpiod_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_ASIS); + if (IS_ERR(priv->gpiod_reset)) { + err = PTR_ERR(priv->gpiod_reset); + dev_err(dev, "Failed to get reset gpio: %d\n", err); + return err; + } + + if (np && of_property_read_u32(np, "clock-frequency", &clk_rate)) + clk_rate = 0; + + priv->clk = devm_clk_get_optional(dev, "main_clk"); + if (IS_ERR(priv->clk)) { + err = PTR_ERR(priv->clk); + dev_err(dev, "Can't get phy clock: %d\n", err); + return err; + } + if (priv->clk && clk_rate) { + err = clk_set_rate(priv->clk, clk_rate); + if (err) { + dev_err(dev, "Error setting clock rate\n"); + return err; + } + } + + priv->vcc = devm_regulator_get_optional(dev, "vcc"); + if (IS_ERR(priv->vcc)) { + err = PTR_ERR(priv->vcc); + if (err == -ENODEV || err == -ENOENT) { + priv->vcc = NULL; + } else { + dev_err(dev, "Error getting vcc regulator: %d\n", err); + return err; + } + } + + phy = devm_phy_create(dev, NULL, &phy_usb_generic_ops); + if (IS_ERR(phy)) { + err = PTR_ERR(phy); + dev_err(dev, "Failed to create PHY: %d\n", err); + return err; + } + phy_set_drvdata(phy, priv); + + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (IS_ERR(provider)) { + err = PTR_ERR(provider); + dev_err(dev, "Failed to register PHY provider: %d\n", err); + return err; + } + + return 0; +} + +static const struct of_device_id phy_usb_nop_dt_ids[] = { + { .compatible = "phy-usb-generic" }, + { .compatible = "usb-nop-xceiv" }, + { } +}; +MODULE_DEVICE_TABLE(of, phy_usb_nop_dt_ids); + +static struct platform_driver phy_usb_generic_driver = { + .probe = phy_usb_generic_probe, + .driver = { + .name = "phy_usb_generic", + .of_match_table = phy_usb_nop_dt_ids, + }, +}; +module_platform_driver(phy_usb_generic_driver); + +MODULE_AUTHOR("Kalray Inc"); +MODULE_DESCRIPTION("Generic USB PHY driver"); +MODULE_LICENSE("GPL");
I recently encountered some limitations when using the usb-nop-xceiv driver using the usb-phy subsystem. The situation is: I have a board with two external usb phys (ULPI) that only needs to be reset by the USB controller. However both phys shares the same reset line, which will get toggled twice by the USB driver, once by controller. This is what I observed with the current Linux usb-nop-xceiv driver: _______ ___ _________ RESET: \__________________________/ \____/ 1^ 2^ 3^ 4^ 1. and 2. first controller toggle the reset 3. and 4. second controller toggle the reset After the second toggle the first driver didn't expected the reset and causing issues, but I don't recall what exactly, it is maybe a driver that simply fail to get probed. The following is what I observed when using the "usb-nop-xceiv" driver in Barebox, which is a bit different than the Linux one. _______ _________________ RESET: \__________________________/ 1^ 2^ In this case the reset is only toggled once, this is because the phy driver count the number of time it has called init and power_on, which is exactly what is done by the generic phy subsystem in Linux, but not by the "legacy" usb-nop-xceiv usb-phy driver. This difference in behavior is what motivated to "port" the existing usb-nop-xceiv driver to the generic phy subsystem. However this is far from being complete... I've only tested the reset function for this nop phy, and it lack a lot of features from the original driver to be a valid replacement for it. I would like to know if there is an interest in converting the current usb-nop-xceiv driver to the generic phy subsystem? I would like to keep the usb-nop-xceiv compatible as it used by Barebox and it works OK. If a new compatible is added then device-tree nodes shouldn't have both, the new and usb-nop-xceiv, compatible because of the specific check in phy-core.c which will always return ENODEV. Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu> --- drivers/phy/Makefile | 1 + drivers/phy/phy-core.c | 4 - drivers/phy/phy-usb-generic.c | 241 ++++++++++++++++++++++++++++++++++ 3 files changed, 242 insertions(+), 4 deletions(-) create mode 100644 drivers/phy/phy-usb-generic.c