@@ -1914,55 +1914,55 @@ static const struct driver_info at_umc2000sp_info = {
static const struct usb_device_id products[] = {
{
/* ASIX AX88179 10/100/1000 */
- USB_DEVICE(0x0b95, 0x1790),
+ USB_DEVICE_AND_INTERFACE_INFO(0x0b95, 0x1790, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&ax88179_info,
}, {
/* ASIX AX88178A 10/100/1000 */
- USB_DEVICE(0x0b95, 0x178a),
+ USB_DEVICE_AND_INTERFACE_INFO(0x0b95, 0x178a, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&ax88178a_info,
}, {
/* Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge Controller */
- USB_DEVICE(0x04b4, 0x3610),
+ USB_DEVICE_AND_INTERFACE_INFO(0x04b4, 0x3610, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&cypress_GX3_info,
}, {
/* D-Link DUB-1312 USB 3.0 to Gigabit Ethernet Adapter */
- USB_DEVICE(0x2001, 0x4a00),
+ USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x4a00, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&dlink_dub1312_info,
}, {
/* Sitecom USB 3.0 to Gigabit Adapter */
- USB_DEVICE(0x0df6, 0x0072),
+ USB_DEVICE_AND_INTERFACE_INFO(0x0df6, 0x0072, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&sitecom_info,
}, {
/* Samsung USB Ethernet Adapter */
- USB_DEVICE(0x04e8, 0xa100),
+ USB_DEVICE_AND_INTERFACE_INFO(0x04e8, 0xa100, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&samsung_info,
}, {
/* Lenovo OneLinkDock Gigabit LAN */
- USB_DEVICE(0x17ef, 0x304b),
+ USB_DEVICE_AND_INTERFACE_INFO(0x17ef, 0x304b, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&lenovo_info,
}, {
/* Belkin B2B128 USB 3.0 Hub + Gigabit Ethernet Adapter */
- USB_DEVICE(0x050d, 0x0128),
+ USB_DEVICE_AND_INTERFACE_INFO(0x050d, 0x0128, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&belkin_info,
}, {
/* Toshiba USB 3.0 GBit Ethernet Adapter */
- USB_DEVICE(0x0930, 0x0a13),
+ USB_DEVICE_AND_INTERFACE_INFO(0x0930, 0x0a13, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&toshiba_info,
}, {
/* Magic Control Technology U3-A9003 USB 3.0 Gigabit Ethernet Adapter */
- USB_DEVICE(0x0711, 0x0179),
+ USB_DEVICE_AND_INTERFACE_INFO(0x0711, 0x0179, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&mct_info,
}, {
/* Allied Telesis AT-UMC2000 USB 3.0/USB 3.1 Gen 1 to Gigabit Ethernet Adapter */
- USB_DEVICE(0x07c9, 0x000e),
+ USB_DEVICE_AND_INTERFACE_INFO(0x07c9, 0x000e, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&at_umc2000_info,
}, {
/* Allied Telesis AT-UMC200 USB 3.0/USB 3.1 Gen 1 to Fast Ethernet Adapter */
- USB_DEVICE(0x07c9, 0x000f),
+ USB_DEVICE_AND_INTERFACE_INFO(0x07c9, 0x000f, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&at_umc200_info,
}, {
/* Allied Telesis AT-UMC2000/SP USB 3.0/USB 3.1 Gen 1 to Gigabit Ethernet Adapter */
- USB_DEVICE(0x07c9, 0x0010),
+ USB_DEVICE_AND_INTERFACE_INFO(0x07c9, 0x0010, 0xff, 0xff, 0xff),
.driver_info = (unsigned long)&at_umc2000sp_info,
},
{ },
The Anker PowerExpand USB-C to Gigabit Ethernet adapter uses this chipset, but exposes CDC Ethernet configurations as well as the vendor specific one. This driver ends up binding first to both CDC interfaces, tries to instantiate two Ethernet interfaces talking to the same device, and the result is a nice fireworks show. Change all the ID matches to specifically match the vendor-specific interface. By default the device comes up in CDC mode and is bound by that driver (which works fine); users may switch it to the vendor interface using sysfs to set bConfigurationValue, at which point the device actually goes through a reconnect cycle and comes back as a endor specific only device, and then this driver binds and works too. Signed-off-by: Hector Martin <marcan@marcan.st> --- drivers/net/usb/ax88179_178a.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-)