From patchwork Mon Oct 10 10:18:11 2022 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Peng Fan (OSS)" X-Patchwork-Id: 13002421 Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id EDD11C433F5 for ; Mon, 10 Oct 2022 10:17:00 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S231617AbiJJKQ7 (ORCPT ); Mon, 10 Oct 2022 06:16:59 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:34112 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S230001AbiJJKQ4 (ORCPT ); Mon, 10 Oct 2022 06:16:56 -0400 Received: from EUR05-DB8-obe.outbound.protection.outlook.com (mail-db8eur05on2060.outbound.protection.outlook.com [40.107.20.60]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 9087B6A4A6; Mon, 10 Oct 2022 03:16:53 -0700 (PDT) ARC-Seal: i=1; a=rsa-sha256; s=arcselector9901; d=microsoft.com; cv=none; b=N0lzxgIKUYBd8sZdH4RPmheugwwNo6r3uQ1ekV6iAEgjn8XDcsi9bZqI75xnrzH/ekd//lRkVB7iPkRJtfBDI1/enjzk19oL3B9GEML0fWzBEIWlneG0rPI08lgoSYQdjD6laX2dG6TrbQJ+8uPs6uYo4piaSK2jRywd0DW/Vag36pR0oo7JTdPtrWSPnjV7YGRE1BMT0L/sog6qK8v5If3wzgMvI+8DPm6zn2HhhuMLfly0Hb6XX5FMtnoa5zzeA4hPwlBtQPOEik46DSiw5tI+1+U2uXQJ++QCDTIqgG/uGpmfQAqWPg0mb0WifDkz/jnH6gbGvmtyyA4qTYGjcQ== ARC-Message-Signature: i=1; a=rsa-sha256; c=relaxed/relaxed; d=microsoft.com; s=arcselector9901; h=From:Date:Subject:Message-ID:Content-Type:MIME-Version:X-MS-Exchange-AntiSpam-MessageData-ChunkCount:X-MS-Exchange-AntiSpam-MessageData-0:X-MS-Exchange-AntiSpam-MessageData-1; bh=ahOejVLbNPQKU2eO9Jbpawt73UF8vy00KzB1W6vGIbs=; b=hlyIoI9d7XLtyQNVCLnlIFAFwlqCiwhZOVbInK177klAzQyDVygCRlHcD4OGWf5gEVHrFh6gyA5Q1LLJmoplFNKCGZ6wuBNq79FXFfOq+8nhbYKQ/o/NkrBswt3JYTe7rM6tWDQC7TS63sybsef9sIbDSs5Puc4yQi0jVtp5WPXMlR4dbbyV/DWjROov7s9jWFGaoNPo952Ni7eholUxEF7HE3A3xccnd+PD+3fhVyyJOlivMAq5GVEK4HstZKQDe71bXHjw7hM/Mh8vgGbDAajMQra2OVukLdCymnrd30byXaMdEBWDofFoKNdixeKPexedAcuZLraJt9gB64Qn/A== ARC-Authentication-Results: i=1; mx.microsoft.com 1; spf=pass smtp.mailfrom=oss.nxp.com; dmarc=pass action=none header.from=oss.nxp.com; dkim=pass header.d=oss.nxp.com; arc=none DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=NXP1.onmicrosoft.com; s=selector2-NXP1-onmicrosoft-com; h=From:Date:Subject:Message-ID:Content-Type:MIME-Version:X-MS-Exchange-SenderADCheck; bh=ahOejVLbNPQKU2eO9Jbpawt73UF8vy00KzB1W6vGIbs=; b=HG0nWG6Sax/Cfy2Ldr/IcsFlpCyswxT6s0WmZt5izmSiKKfu6Mj19Pzil8rM6lefTNtWJy8ZOOFA0J0zPKIAIMAp2FkQLdRGPS4mp4JaSIQzzz34cwMVmoY/vkRL+M4rnjOXM3XV1ZPNOGUxwgMUFQ+7cvEyEx1/1XyXLNbsM+Q= Authentication-Results: dkim=none (message not signed) header.d=none;dmarc=none action=none header.from=oss.nxp.com; Received: from DU0PR04MB9417.eurprd04.prod.outlook.com (2603:10a6:10:358::11) by AS8PR04MB7783.eurprd04.prod.outlook.com (2603:10a6:20b:2a4::17) with Microsoft SMTP Server (version=TLS1_2, cipher=TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384) id 15.20.5709.15; Mon, 10 Oct 2022 10:16:50 +0000 Received: from DU0PR04MB9417.eurprd04.prod.outlook.com ([fe80::ba6:d7ae:a7c9:7a3a]) by DU0PR04MB9417.eurprd04.prod.outlook.com ([fe80::ba6:d7ae:a7c9:7a3a%4]) with mapi id 15.20.5676.028; Mon, 10 Oct 2022 10:16:50 +0000 From: "Peng Fan (OSS)" To: gregkh@linuxfoundation.org, robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org, shawnguo@kernel.org, s.hauer@pengutronix.de Cc: kernel@pengutronix.de, festevam@gmail.com, linux-imx@nxp.com, linux-usb@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, jun.li@nxp.com, Peng Fan Subject: [PATCH 1/6] dt-bindings: usb: ci-hdrc-usb2: convert to yaml Date: Mon, 10 Oct 2022 18:18:11 +0800 Message-Id: <20221010101816.298334-2-peng.fan@oss.nxp.com> X-Mailer: git-send-email 2.37.1 In-Reply-To: <20221010101816.298334-1-peng.fan@oss.nxp.com> References: <20221010101816.298334-1-peng.fan@oss.nxp.com> X-ClientProxiedBy: SG2P153CA0048.APCP153.PROD.OUTLOOK.COM (2603:1096:4:c6::17) To DU0PR04MB9417.eurprd04.prod.outlook.com (2603:10a6:10:358::11) MIME-Version: 1.0 X-MS-Exchange-MessageSentRepresentingType: 1 X-MS-PublicTrafficType: Email X-MS-TrafficTypeDiagnostic: DU0PR04MB9417:EE_|AS8PR04MB7783:EE_ X-MS-Office365-Filtering-Correlation-Id: e51a2fdf-6170-48a9-db62-08daaaa88b46 X-MS-Exchange-SharedMailbox-RoutingAgent-Processed: True X-MS-Exchange-SenderADCheck: 1 X-MS-Exchange-AntiSpam-Relay: 0 X-Microsoft-Antispam: BCL:0; X-Microsoft-Antispam-Message-Info: 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 X-Forefront-Antispam-Report: CIP:255.255.255.255;CTRY:;LANG:en;SCL:1;SRV:;IPV:NLI;SFV:NSPM;H:DU0PR04MB9417.eurprd04.prod.outlook.com;PTR:;CAT:NONE;SFS:(13230022)(4636009)(366004)(396003)(136003)(376002)(39860400002)(346002)(451199015)(316002)(7416002)(2906002)(6486002)(186003)(1076003)(2616005)(66476007)(41300700001)(6666004)(66946007)(83380400001)(66556008)(478600001)(8936002)(8676002)(30864003)(4326008)(5660300002)(966005)(26005)(6506007)(52116002)(86362001)(38100700002)(6512007)(38350700002);DIR:OUT;SFP:1101; X-MS-Exchange-AntiSpam-MessageData-ChunkCount: 1 X-MS-Exchange-AntiSpam-MessageData-0: 3sJpOmWAByKasFNl+SURObPM7+oDPnQBjKSKKBMKmIlc6MgmxqZpBViZvSgYBwkdiYBigqc9zfOyT+1Wc/oMpoPYu3ZNvQOwZCqpUKt6ULKvJqiE9RZZ7+L4KlzNsQt7zuiUQyigtD+7N/v9SL3P3tO28ewZ0qp81APRtuwPd20c6n+8LfTHgrTzKH7nt3V0YlMzSPlUxs9KqgTMzq1KwPhJMdVXicgYtNxCML2Jx2GUGfiGeSelKsi/rEf2yLK6vIeRUZWCWzKuGpB9rFLBLx9ydxQFZKCeFkdad21DfcIesS0oqIF09T4jngrz7VeEuISsTApW3EHEqUZPJDazRr1pDLG08eyDTDcdOP+yD27tgZh76UxoYW+x+mdMm2DCI2nVQCsZ0d1UYAilEWr7J+73W60AJwl6KH3CHqBfnPpzotjvf/HWmzlqI16g+gGu1fxf+vrqXuEDKuHajJVkkkzzXQ3EcrEUILAC154AFh30XNa5YMuO7uZh9/8lSFdOFLNDTeSmiRS7NZk57rn2s/2URkMrLFHxl3vqtsUxlpvMXQ2ryP/iH83Jr4ixv64V2GVTru9dU0/Y3E8/Yb7TuzQbWlC8Ao0ycaxIfTUS2SVlq1D6TFdvgzxzqgpsS6Jcxv9GiGmRYQeI99t3A9G8dIXMAO6L6jpXeGn8Fm1VTywSuYe+8oTpZk1R7tQpDD6xmZp0hBExME5Tit+SvgVo6zn8126EcKQlUvexc8UrOESnWHLy9m1nwbYbS9r40Nvqqy6rWDk8T+MnMB0jiq6TOnePcP5PyasBx4sMrOV25OtYQpLuCZ9WlJDQ6YlkKouGX+1vLsEPK0/KH7q0Hy8CmdHBd19lPe46ItsU1iL0kYGsnGExEv+DPF9ntYrQkzeA4o30rUUvSTmW9KQrDiOu8oTnyzrMgPI429Xvwfi7LCEVk5BbO7ehfSCJFkvslxmOk+ifiOsxEQzfbyk1Jlpgorq2PEED4cr8thDLHbxei0JKoWPvlBnJg2coa/nh7MpkujMlGwzarp3d2z9+ta94xWEzb9xwCZPTvK2ta3XRIwmbdyPBRPJmjbxb27fILTRxkNDwULQPwroCjaatmtXOqx7e864V69iOHLa+49KTJy31GCahFa3pEHJzaR6NEhMWsI/roLMFJlwKuG6rmWb9w/WgP0ZoZ9TdmtX2XK8Z/W+jKm9gpseClLZPw+f1gFZdFkfww/8Wpld6OaeUhJKNg73iSqPUDIV+JZ3XENRtOIBwafnXncv6k7hTZqBm822Byt/wDbf2qF7EtVpi3KKp6OQLidLKsLChKao+fXaVxonZOsSkIwFn7SID9IpSeWH7aJkn1F4EbG70cgent+fnY1RX9D4dUjrIOoWBspKh3CQkOi+1nwtJ/DYmUA+AEQfS5ps95pKY3Rx8gHXu2umw7ppZZ413lf8sbsp+yBYe4n01JnBT8Z+Scgpb95UO5i5GE6jAQZoDyFkOlol1F6egS82tx9LUw+cSqINB/3H2xDyjgu5Nt3YrM/Y+9Y+bM1rSO0EpKvDUosfs/SaqvHfT8I2HfE9FeVRz8uf5xaEDKLCPXLwMOaNXqk//tR7M4Wed X-OriginatorOrg: oss.nxp.com X-MS-Exchange-CrossTenant-Network-Message-Id: e51a2fdf-6170-48a9-db62-08daaaa88b46 X-MS-Exchange-CrossTenant-AuthSource: DU0PR04MB9417.eurprd04.prod.outlook.com X-MS-Exchange-CrossTenant-AuthAs: Internal X-MS-Exchange-CrossTenant-OriginalArrivalTime: 10 Oct 2022 10:16:50.1592 (UTC) X-MS-Exchange-CrossTenant-FromEntityHeader: Hosted X-MS-Exchange-CrossTenant-Id: 686ea1d3-bc2b-4c6f-a92c-d99c5c301635 X-MS-Exchange-CrossTenant-MailboxType: HOSTED X-MS-Exchange-CrossTenant-UserPrincipalName: mgC9dlmUmF6le/7uBtbFGSR0SgxbLEVcozTzV7pf+IH9K0QG1hil01w+Mz9KhabT59hq0G8fXJYPqjFbFwTnbQ== X-MS-Exchange-Transport-CrossTenantHeadersStamped: AS8PR04MB7783 Precedence: bulk List-ID: X-Mailing-List: linux-usb@vger.kernel.org From: Peng Fan Convert the binding to yaml format Signed-off-by: Peng Fan --- .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 158 --------- .../devicetree/bindings/usb/ci-hdrc-usb2.yaml | 306 ++++++++++++++++++ 2 files changed, 306 insertions(+), 158 deletions(-) delete mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt create mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt deleted file mode 100644 index ba51fb1252b9..000000000000 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ /dev/null @@ -1,158 +0,0 @@ -* USB2 ChipIdea USB controller for ci13xxx - -Required properties: -- compatible: should be one of: - "fsl,imx23-usb" - "fsl,imx27-usb" - "fsl,imx28-usb" - "fsl,imx6q-usb" - "fsl,imx6sl-usb" - "fsl,imx6sx-usb" - "fsl,imx6ul-usb" - "fsl,imx7d-usb" - "fsl,imx7ulp-usb" - "lsi,zevio-usb" - "qcom,ci-hdrc" - "chipidea,usb2" - "xlnx,zynq-usb-2.20a" - "nvidia,tegra20-udc" - "nvidia,tegra30-udc" - "nvidia,tegra114-udc" - "nvidia,tegra124-udc" -- reg: base address and length of the registers -- interrupts: interrupt for the USB controller - -Recommended properies: -- phy_type: the type of the phy connected to the core. Should be one - of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this - property the PORTSC register won't be touched. -- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" - -Deprecated properties: -- usb-phy: phandle for the PHY device. Use "phys" instead. -- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead. - -Optional properties: -- clocks: reference to the USB clock -- phys: reference to the USB PHY -- phy-names: should be "usb-phy" -- vbus-supply: reference to the VBUS regulator -- maximum-speed: limit the maximum connection speed to "full-speed". -- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts -- itc-setting: interrupt threshold control register control, the setting - should be aligned with ITC bits at register USBCMD. -- ahb-burst-config: it is vendor dependent, the required value should be - aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This - property is used to change AHB burst configuration, check the chipidea - spec for meaning of each value. If this property is not existed, it - will use the reset value. -- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword - (4 bytes), This register represents the maximum length of a the burst - in 32-bit words while moving data from system memory to the USB - bus, the value of this property will only take effect if property - "ahb-burst-config" is set to 0, if this property is missing the reset - default of the hardware implementation will be used. -- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword - (4 bytes), This register represents the maximum length of a the burst - in 32-bit words while moving data from the USB bus to system memory, - the value of this property will only take effect if property - "ahb-burst-config" is set to 0, if this property is missing the reset - default of the hardware implementation will be used. -- extcon: phandles to external connector devices. First phandle should point to - external connector, which provide "USB" cable events, the second should point - to external connector device, which provide "USB-HOST" cable events. If one - of the external connector devices is not required, empty <0> phandle should - be specified. -- phy-clkgate-delay-us: the delay time (us) between putting the PHY into - low power mode and gating the PHY clock. -- non-zero-ttctrl-ttha: after setting this property, the value of register - ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default - value. It needs to be very carefully for setting this property, it is - recommended that consult with your IC engineer before setting this value. - On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this - property only affects siTD. - If this property is not set, the max packet size is 1023 bytes, and if - the total of packet size for pervious transactions are more than 256 bytes, - it can't accept any transactions within this frame. The use case is single - transaction, but higher frame rate. - If this property is set, the max packet size is 188 bytes, it can handle - more transactions than above case, it can accept transactions until it - considers the left room size within frame is less than 188 bytes, software - needs to make sure it does not send more than 90% - maximum_periodic_data_per_frame. The use case is multiple transactions, but - less frame rate. -- mux-controls: The mux control for toggling host/device output of this - controller. It's expected that a mux state of 0 indicates device mode and a - mux state of 1 indicates host mode. -- mux-control-names: Shall be "usb_switch" if mux-controls is specified. -- pinctrl-names: Names for optional pin modes in "default", "host", "device". - In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this - case, the "idle" state needs to pull down the data and strobe pin - and the "active" state needs to pull up the strobe pin. -- pinctrl-n: alternate pin modes - -i.mx specific properties -- fsl,usbmisc: phandler of non-core register device, with one - argument that indicate usb controller index -- disable-over-current: disable over current detect -- over-current-active-low: over current signal polarity is active low. -- over-current-active-high: over current signal polarity is active high. - It's recommended to specify the over current polarity. -- power-active-high: power signal polarity is active high -- external-vbus-divider: enables off-chip resistor divider for Vbus -- samsung,picophy-pre-emp-curr-control: HS Transmitter Pre-Emphasis Current - Control. This signal controls the amount of current sourced to the - USB_OTG*_DP and USB_OTG*_DN pins after a J-to-K or K-to-J transition. - The range is from 0x0 to 0x3, the default value is 0x1. - Details can refer to TXPREEMPAMPTUNE0 bits of USBNC_n_PHY_CFG1. -- samsung,picophy-dc-vol-level-adjust: HS DC Voltage Level Adjustment. - Adjust the high-speed transmitter DC level voltage. - The range is from 0x0 to 0xf, the default value is 0x3. - Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1. - -Example: - - usb@f7ed0000 { - compatible = "chipidea,usb2"; - reg = <0xf7ed0000 0x10000>; - interrupts = ; - clocks = <&chip CLKID_USB0>; - phys = <&usb_phy0>; - phy-names = "usb-phy"; - vbus-supply = <®_usb0_vbus>; - itc-setting = <0x4>; /* 4 micro-frames */ - /* Incremental burst of unspecified length */ - ahb-burst-config = <0x0>; - tx-burst-size-dword = <0x10>; /* 64 bytes */ - rx-burst-size-dword = <0x10>; - extcon = <0>, <&usb_id>; - phy-clkgate-delay-us = <400>; - mux-controls = <&usb_switch>; - mux-control-names = "usb_switch"; - }; - -Example for HSIC: - - usb@2184400 { - compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; - reg = <0x02184400 0x200>; - interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX6QDL_CLK_USBOH3>; - fsl,usbphy = <&usbphynop1>; - fsl,usbmisc = <&usbmisc 2>; - phy_type = "hsic"; - dr_mode = "host"; - ahb-burst-config = <0x0>; - tx-burst-size-dword = <0x10>; - rx-burst-size-dword = <0x10>; - pinctrl-names = "idle", "active"; - pinctrl-0 = <&pinctrl_usbh2_idle>; - pinctrl-1 = <&pinctrl_usbh2_active>; - #address-cells = <1>; - #size-cells = <0>; - - usbnet: ethernet@1 { - compatible = "usb424,9730"; - reg = <1>; - }; - }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml new file mode 100644 index 000000000000..1c10691c45f2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml @@ -0,0 +1,306 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB2 ChipIdea USB controller for ci13xxx Binding + +maintainers: + - Greg Kroah-Hartman + +properties: + compatible: + oneOf: + - enum: + - chipidea,usb2 + - lsi,zevio-usb + - nvidia,tegra20-udc + - nvidia,tegra30-udc + - nvidia,tegra114-udc + - nvidia,tegra124-udc + - qcom,ci-hdrc + - items: + - enum: + - fsl,imx23-usb + - fsl,imx25-usb + - fsl,imx28-usb + - fsl,imx6q-usb + - fsl,imx6sl-usb + - fsl,imx6sx-usb + - fsl,imx6ul-usb + - fsl,imx7d-usb + - const: fsl,imx27-usb + - items: + - const: fsl,imx7ulp-usb + - const: fsl,imx6ul-usb + - items: + - const: lsi,zevio-usb + - items: + - const: xlnx,zynq-usb-2.20a + - const: chipidea,usb2 + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + itc-setting: + description: + interrupt threshold control register control, the setting should be + aligned with ITC bits at register USBCMD. + $ref: /schemas/types.yaml#/definitions/uint32 + + ahb-burst-config: + description: + it is vendor dependent, the required value should be aligned with + AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is + used to change AHB burst configuration, check the chipidea spec for + meaning of each value. If this property is not existed, it will use + the reset value. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x7 + + tx-burst-size-dword: + description: + it is vendor dependent, the tx burst size in dword (4 bytes), This + register represents the maximum length of a the burst in 32-bit + words while moving data from system memory to the USB bus, the value + of this property will only take effect if property "ahb-burst-config" + is set to 0, if this property is missing the reset default of the + hardware implementation will be used. + $ref: /schemas/types.yaml#/definitions/uint32 + + rx-burst-size-dword: + description: + it is vendor dependent, the rx burst size in dword (4 bytes), This + register represents the maximum length of a the burst in 32-bit words + while moving data from the USB bus to system memory, the value of + this property will only take effect if property "ahb-burst-config" + is set to 0, if this property is missing the reset default of the + hardware implementation will be used. + $ref: /schemas/types.yaml#/definitions/uint32 + + extcon: + description: | + Phandles to external connector devices. First phandle should point + to external connector, which provide "USB" cable events, the second + should point to external connector device, which provide "USB-HOST" + cable events. If one of the external connector devices is not + required, empty <0> phandle should be specified. + + phy-clkgate-delay-us: + description: | + The delay time (us) between putting the PHY into low power mode and + gating the PHY clock. + + non-zero-ttctrl-ttha: + description: | + After setting this property, the value of register ttctrl.ttha + will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it + is recommended that consult with your IC engineer before setting + this value. On the most of chipidea platforms, the "usage_tt" flag + at RTL is 0, so this property only affects siTD. + + If this property is not set, the max packet size is 1023 bytes, and + if the total of packet size for pervious transactions are more than + 256 bytes, it can't accept any transactions within this frame. The + use case is single transaction, but higher frame rate. + + If this property is set, the max packet size is 188 bytes, it can + handle more transactions than above case, it can accept transactions + until it considers the left room size within frame is less than 188 + bytes, software needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple + transactions, but less frame rate. + + mux-controls: + description: | + The mux control for toggling host/device output of this controller. + It's expected that a mux state of 0 indicates device mode and a mux + state of 1 indicates host mode. + + mux-control-names: + description: Shall be "usb_switch" if mux-controls is specified. + + pinctrl-names: + description: | + Names for optional pin modes in "default", "host", "device". + In case of HSIC-mode, "idle" and "active" pin modes are mandatory. + In this case, the "idle" state needs to pull down the data and + strobe pin and the "active" state needs to pull up the strobe pin. + + pinctrl-0: + maxItems: 1 + + pinctrl-1: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: usb-phy + + vbus-supply: + description: reference to the VBUS regulator. + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: usb-drd.yaml# + - $ref: usb-hcd.yaml# + - if: + properties: + mux-controls: + true + then: + properties: + mux-control-names: + const: usb_switch + - if: + properties: + phy_type: + const: hsic + + required: + - phy_type + then: + properties: + pinctrl-names: + items: + - const: idle + - const: active + else: + properties: + pinctrl-names: + oneOf: + - items: + - const: default + - enum: + - host + - device + - items: + - const: default + - if: + properties: + compatible: + enum: + - fsl,imx23-usb + - fsl,imx25-usb + - fsl,imx27-usb + - fsl,imx28-usb + - fsl,imx6q-usb + - fsl,imx6sl-usb + - fsl,imx6sx-usb + - fsl,imx6ul-usb + - fsl,imx7d-usb + - fsl,imx7ulp-usb + then: + properties: + fsl,usbmisc: + description: + Phandler of non-core register device, with one argument that + indicate usb controller index + + disable-over-current: + description: disable over current detect + + over-current-active-low: + description: over current signal polarity is active low + + over-current-active-high: + description: | + Over current signal polarity is active high. It's recommended to + specify the over current polarity. + + power-active-high: + description: power signal polarity is active high + + external-vbus-divider: + description: enables off-chip resistor divider for Vbus + + samsung,picophy-pre-emp-curr-control: + description: | + HS Transmitter Pre-Emphasis Current Control. This signal controls + the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN + pins after a J-to-K or K-to-J transition. The range is from 0x0 to + 0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0 + bits of USBNC_n_PHY_CFG1. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x3 + + samsung,picophy-dc-vol-level-adjust: + description: | + HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC + level voltage. The range is from 0x0 to 0xf, the default value is + 0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0xf + +additionalProperties: true + +examples: + - | + #include + #include + + usb@f7ed0000 { + compatible = "chipidea,usb2"; + reg = <0xf7ed0000 0x10000>; + interrupts = ; + clocks = <&chip CLKID_USB0>; + phys = <&usb_phy0>; + phy-names = "usb-phy"; + vbus-supply = <®_usb0_vbus>; + itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; + }; + + # Example for HSIC: + - | + #include + #include + + usb@2184400 { + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184400 0x200>; + interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_USBOH3>; + fsl,usbphy = <&usbphynop1>; + fsl,usbmisc = <&usbmisc 2>; + phy_type = "hsic"; + dr_mode = "host"; + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; + pinctrl-names = "idle", "active"; + pinctrl-0 = <&pinctrl_usbh2_idle>; + pinctrl-1 = <&pinctrl_usbh2_active>; + #address-cells = <1>; + #size-cells = <0>; + + usbnet: ethernet@1 { + compatible = "usb424,9730"; + reg = <1>; + }; + }; + +...