| Message ID | 20221112091923.9562-1-frank-w@public-files.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | None | expand |
On Sat, Nov 12, 2022 at 10:19:22AM +0100, Frank Wunderlich wrote: > Add support for Bananapi R3 SBC. > > - SD/eMMC support (switching first 4 bits of data-bus with sw6/D) > - all rj45 ports and both SFP working (eth1/lan4) > - all USB-Ports + SIM-Slot tested > - i2c and all uarts tested > - wifi tested (with eeprom calibration data) > > Signed-off-by: Frank Wunderlich <frank-w@public-files.de> > --- > SPI-NAND/NOR switched (CS by sw5/C) not yet included > this is done with DT-Overlays in my tree, don't know how to do it > in upstream the right way...added dts files for dtbo and added them > with dtbo extension to Makefile works. The device can boot from all 4 storage options. Both, SPI and MMC, can be switched using hardware switches on the board, see https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting So why do the SPI-NAND vs. SPI-NOR switching with device tree overlays and the SD card vs. eMMC switching with dtsi + 2x dts? To me this looks inconsitent. Use either one or the other method. > > changes: > v4: > - add PCIe nodes > - fix sfp-properties of sfp-1 (need to be plural) > thx to Denis Odintsov for this > > v3: > - rename factory-key to reset-key > - add dcin regulator and add it as input for 3v3 (with renaming) > - remove memory-node > - dropped wifi eeprom (calibration) data > - move mmc0 pinctrl to common dtsi and drop sdcard comment > - change mmc pull-up/down to have generic bias-pull* > > v2: > - remove pcie to be added later (discussion about clocks) > - some fixes based on suggestions on ML > - add key suffix like it's done in mt7622-bpi-r64 devicetree > - add dash in sfp node names > - use reg as unit for switch-node > - drop "-3-4" suffix from i2c-pins node name > - fix order in Makefile > --- > arch/arm64/boot/dts/mediatek/Makefile | 2 + > .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts | 31 ++ > .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts | 25 + > .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 458 ++++++++++++++++++ > 4 files changed, 516 insertions(+) > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > index 0ec90cb3ef28..e8902f2cc58f 100644 > --- a/arch/arm64/boot/dts/mediatek/Makefile > +++ b/arch/arm64/boot/dts/mediatek/Makefile > @@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts > new file mode 100644 > index 000000000000..a0ca35b5977e > --- /dev/null > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts > @@ -0,0 +1,31 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2021 MediaTek Inc. > + * Author: Sam.Shih <sam.shih@mediatek.com> > + */ > + > +/dts-v1/; > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/gpio/gpio.h> > + > +#include "mt7986a-bananapi-bpi-r3.dtsi" > + > +/ { > + model = "Bananapi BPI-R3 (emmc)"; > +}; > + > +&mmc0 { > + bus-width = <8>; > + max-frequency = <200000000>; > + cap-mmc-highspeed; > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > + hs400-ds-delay = <0x14014>; > + vmmc-supply = <®_3p3v>; > + vqmmc-supply = <®_1p8v>; > + non-removable; > + no-sd; > + no-sdio; > + status = "okay"; > +}; > + > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts > new file mode 100644 > index 000000000000..06e4691cb815 > --- /dev/null > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts > @@ -0,0 +1,25 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2021 MediaTek Inc. > + * Author: Sam.Shih <sam.shih@mediatek.com> > + */ > + > +/dts-v1/; > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/gpio/gpio.h> > + > +#include "mt7986a-bananapi-bpi-r3.dtsi" > + > +/ { > + model = "Bananapi BPI-R3 (sdmmc)"; > +}; > + > +&mmc0 { > + bus-width = <4>; > + max-frequency = <52000000>; > + cap-sd-highspeed; > + vmmc-supply = <®_3p3v>; > + vqmmc-supply = <®_1p8v>; > + status = "okay"; > +}; > + > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi > new file mode 100644 > index 000000000000..def16e36f1e6 > --- /dev/null > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi > @@ -0,0 +1,458 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2021 MediaTek Inc. > + * Authors: Sam.Shih <sam.shih@mediatek.com> > + * Frank Wunderlich <frank-w@public-files.de> > + * Daniel Golle <daniel@makrotopia.org> > + */ > + > +/dts-v1/; > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/mt65xx.h> > + > +#include "mt7986a.dtsi" > + > +/ { > + model = "Bananapi BPI-R3"; > + compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; > + > + aliases { > + serial0 = &uart0; > + ethernet0 = &gmac0; > + ethernet1 = &gmac1; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + dcin: regulator-12vd { > + compatible = "regulator-fixed"; > + regulator-name = "12vd"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + reset-key { > + label = "reset"; > + linux,code = <KEY_RESTART>; > + gpios = <&pio 9 GPIO_ACTIVE_LOW>; > + }; > + > + wps-key { > + label = "wps"; > + linux,code = <KEY_WPS_BUTTON>; > + gpios = <&pio 10 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + /* i2c of the left SFP cage (wan) */ > + i2c_sfp1: i2c-gpio-0 { > + compatible = "i2c-gpio"; > + sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + /* i2c of the right SFP cage (lan) */ > + i2c_sfp2: i2c-gpio-1 { > + compatible = "i2c-gpio"; > + sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + green_led: led-0 { > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_POWER; > + gpios = <&pio 69 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + }; > + > + blue_led: led-1 { > + color = <LED_COLOR_ID_BLUE>; > + function = LED_FUNCTION_STATUS; > + gpios = <&pio 86 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + }; > + > + reg_1p8v: regulator-1p8v { > + compatible = "regulator-fixed"; > + regulator-name = "1.8vd"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + vin-supply = <&dcin>; > + }; > + > + reg_3p3v: regulator-3p3v { > + compatible = "regulator-fixed"; > + regulator-name = "3.3vd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + vin-supply = <&dcin>; > + }; > + > + reg_5v: regulator-5v { > + compatible = "regulator-fixed"; > + regulator-name = "fixed-5p1"; > + regulator-min-microvolt = <5100000>; > + regulator-max-microvolt = <5100000>; > + regulator-boot-on; > + regulator-always-on; > + vin-supply = <&dcin>; > + }; > + > + /* left SFP cage (wan) */ > + sfp1: sfp-1 { > + compatible = "sff,sfp"; > + i2c-bus = <&i2c_sfp1>; > + los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>; > + mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>; > + tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>; > + tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>; > + }; > + > + /* right SFP cage (lan) */ > + sfp2: sfp-2 { > + compatible = "sff,sfp"; > + i2c-bus = <&i2c_sfp2>; > + los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>; > + mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>; > + tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>; > + tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +&crypto { > + status = "okay"; > +}; > + > +ð { > + status = "okay"; > + > + gmac0: mac@0 { > + compatible = "mediatek,eth-mac"; > + reg = <0>; > + phy-mode = "2500base-x"; > + > + fixed-link { > + speed = <2500>; > + full-duplex; > + pause; > + }; > + }; > + > + gmac1: mac@1 { > + compatible = "mediatek,eth-mac"; > + reg = <1>; > + phy-mode = "2500base-x"; > + sfp = <&sfp1>; > + managed = "in-band-status"; > + }; > + > + mdio: mdio-bus { > + #address-cells = <1>; > + #size-cells = <0>; > + }; > +}; > + > +&mdio { > + switch: switch@31 { > + compatible = "mediatek,mt7531"; > + reg = <31>; > + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +&mmc0 { > + pinctrl-names = "default", "state_uhs"; > + pinctrl-0 = <&mmc0_pins_default>; > + pinctrl-1 = <&mmc0_pins_uhs>; > +}; > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c_pins>; > + status = "okay"; > +}; > + > +&pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie_pins>; > + status = "okay"; > +}; > + > +&pcie_phy { > + status = "okay"; > +}; > + > +&pio { > + i2c_pins: i2c-pins { > + mux { > + function = "i2c"; > + groups = "i2c"; > + }; > + }; > + > + mmc0_pins_default: mmc0-pins { > + mux { > + function = "emmc"; > + groups = "emmc_51"; > + }; > + conf-cmd-dat { > + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", > + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", > + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; > + input-enable; > + drive-strength = <4>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ > + }; > + conf-clk { > + pins = "EMMC_CK"; > + drive-strength = <6>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ > + }; > + conf-ds { > + pins = "EMMC_DSL"; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ > + }; > + conf-rst { > + pins = "EMMC_RSTB"; > + drive-strength = <4>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ > + }; > + }; > + > + mmc0_pins_uhs: mmc0-uhs-pins { > + mux { > + function = "emmc"; > + groups = "emmc_51"; > + }; > + conf-cmd-dat { > + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", > + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", > + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; > + input-enable; > + drive-strength = <4>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ > + }; > + conf-clk { > + pins = "EMMC_CK"; > + drive-strength = <6>; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ > + }; > + conf-ds { > + pins = "EMMC_DSL"; > + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ > + }; > + conf-rst { > + pins = "EMMC_RSTB"; > + drive-strength = <4>; > + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ > + }; > + }; > + > + pcie_pins: pcie-pins { > + mux { > + function = "pcie"; > + groups = "pcie_clk", "pcie_pereset"; > + }; > + }; > + > + spi_flash_pins: spi-flash-pins { > + mux { > + function = "spi"; > + groups = "spi0", "spi0_wp_hold"; > + }; > + }; > + > + spic_pins: spic-pins { > + mux { > + function = "spi"; > + groups = "spi1_0"; > + }; > + }; > + > + uart1_pins: uart1-pins { > + mux { > + function = "uart"; > + groups = "uart1_rx_tx"; > + }; > + }; > + > + uart2_pins: uart2-pins { > + mux { > + function = "uart"; > + groups = "uart2_0_rx_tx"; > + }; > + }; > + > + wf_2g_5g_pins: wf-2g-5g-pins { > + mux { > + function = "wifi"; > + groups = "wf_2g", "wf_5g"; > + }; > + conf { > + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", > + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", > + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", > + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", > + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", > + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", > + "WF1_TOP_CLK", "WF1_TOP_DATA"; > + drive-strength = <4>; > + }; > + }; > + > + wf_dbdc_pins: wf-dbdc-pins { > + mux { > + function = "wifi"; > + groups = "wf_dbdc"; > + }; > + conf { > + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", > + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", > + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", > + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", > + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", > + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", > + "WF1_TOP_CLK", "WF1_TOP_DATA"; > + drive-strength = <4>; > + }; > + }; > + > + wf_led_pins: wf-led-pins { > + mux { > + function = "led"; > + groups = "wifi_led"; > + }; > + }; > +}; > + > +&spi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi_flash_pins>; > + cs-gpios = <0>, <0>; > + status = "okay"; > +}; > + > +&spi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spic_pins>; > + cs-gpios = <0>, <0>; > + status = "okay"; > +}; > + > +&ssusb { > + vusb33-supply = <®_3p3v>; > + vbus-supply = <®_5v>; > + status = "okay"; > +}; > + > +&switch { > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + label = "wan"; > + }; > + > + port@1 { > + reg = <1>; > + label = "lan0"; > + }; > + > + port@2 { > + reg = <2>; > + label = "lan1"; > + }; > + > + port@3 { > + reg = <3>; > + label = "lan2"; > + }; > + > + port@4 { > + reg = <4>; > + label = "lan3"; > + }; > + > + port5: port@5 { > + reg = <5>; > + label = "lan4"; > + phy-mode = "2500base-x"; > + sfp = <&sfp2>; > + managed = "in-band-status"; > + }; > + > + port@6 { > + reg = <6>; > + label = "cpu"; > + ethernet = <&gmac0>; > + phy-mode = "2500base-x"; > + > + fixed-link { > + speed = <2500>; > + full-duplex; > + pause; > + }; > + }; > + }; > +}; > + > +&trng { > + status = "okay"; > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart1_pins>; > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart2_pins>; > + status = "okay"; > +}; > + > +&usb_phy { > + status = "okay"; > +}; > + > +&watchdog { > + status = "okay"; > +}; > + > +&wifi { > + status = "okay"; > + pinctrl-names = "default", "dbdc"; > + pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>; > + pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>; > +}; > + > -- > 2.34.1 > >
Am 15. November 2022 23:01:20 MEZ schrieb Daniel Golle <daniel@makrotopia.org>: >The device can boot from all 4 storage options. Both, SPI and MMC, can >be switched using hardware switches on the board, see >https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting > >So why do the SPI-NAND vs. SPI-NOR switching with device tree overlays >and the SD card vs. eMMC switching with dtsi + 2x dts? To me this looks >inconsitent. Use either one or the other method. Hi Daniel It is still in discussion,if mainline-kernel will support devicetree-overlays [1]. I used this way to have at least 1 dtb without overlay for booting kernel from sdcard which is the only external storage. If mainline kernel rejects dto, we have no "broken" dtb which only allows bootup with initrd. We can boot this board from sdcard with mainline code only (maybe some users don't need emmc,nand,nor). As you cannot delete (sd specific) properties in overlays,i added emmc variant. And now we can use overlays to support spi devices,which are not needed for first bootup,but to access emmc. Imho my current sd/emmc dts can be easily converted to dtso and base dtsi needs only to be renamed. But all only if the big question below is answered. [1] https://patchwork.kernel.org/project/linux-mediatek/patch/20221106085034.12582-12-linux@fw-web.de/#25085681 regards Frank
On Wed, Nov 16, 2022 at 3:07 AM Frank Wunderlich <frank-w@public-files.de> wrote: > > Am 15. November 2022 23:01:20 MEZ schrieb Daniel Golle <daniel@makrotopia.org>: > > > >The device can boot from all 4 storage options. Both, SPI and MMC, can > >be switched using hardware switches on the board, see > >https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting > > > >So why do the SPI-NAND vs. SPI-NOR switching with device tree overlays > >and the SD card vs. eMMC switching with dtsi + 2x dts? To me this looks > >inconsitent. Use either one or the other method. > > Hi Daniel > > It is still in discussion,if mainline-kernel will support devicetree-overlays [1]. No it's not. We're just in the middle of renaming overlay .dts files to .dtso. Overlays have been supported for the last 1.5 years. Rob
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index 0ec90cb3ef28..e8902f2cc58f 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts new file mode 100644 index 000000000000..a0ca35b5977e --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts @@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Sam.Shih <sam.shih@mediatek.com> + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> + +#include "mt7986a-bananapi-bpi-r3.dtsi" + +/ { + model = "Bananapi BPI-R3 (emmc)"; +}; + +&mmc0 { + bus-width = <8>; + max-frequency = <200000000>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + hs400-ds-delay = <0x14014>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts new file mode 100644 index 000000000000..06e4691cb815 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Sam.Shih <sam.shih@mediatek.com> + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> + +#include "mt7986a-bananapi-bpi-r3.dtsi" + +/ { + model = "Bananapi BPI-R3 (sdmmc)"; +}; + +&mmc0 { + bus-width = <4>; + max-frequency = <52000000>; + cap-sd-highspeed; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi new file mode 100644 index 000000000000..def16e36f1e6 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi @@ -0,0 +1,458 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Authors: Sam.Shih <sam.shih@mediatek.com> + * Frank Wunderlich <frank-w@public-files.de> + * Daniel Golle <daniel@makrotopia.org> + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/mt65xx.h> + +#include "mt7986a.dtsi" + +/ { + model = "Bananapi BPI-R3"; + compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + dcin: regulator-12vd { + compatible = "regulator-fixed"; + regulator-name = "12vd"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset-key { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + wps-key { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + }; + + /* i2c of the left SFP cage (wan) */ + i2c_sfp1: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + /* i2c of the right SFP cage (lan) */ + i2c_sfp2: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + leds { + compatible = "gpio-leds"; + + green_led: led-0 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_POWER; + gpios = <&pio 69 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + blue_led: led-1 { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_STATUS; + gpios = <&pio 86 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1.8vd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3.3vd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5p1"; + regulator-min-microvolt = <5100000>; + regulator-max-microvolt = <5100000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + /* left SFP cage (wan) */ + sfp1: sfp-1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>; + }; + + /* right SFP cage (lan) */ + sfp2: sfp-2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + sfp = <&sfp1>; + managed = "in-band-status"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + switch: switch@31 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + }; +}; + +&mmc0 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins>; + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pins>; + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + +&pio { + i2c_pins: i2c-pins { + mux { + function = "i2c"; + groups = "i2c"; + }; + }; + + mmc0_pins_default: mmc0-pins { + mux { + function = "emmc"; + groups = "emmc_51"; + }; + conf-cmd-dat { + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; + input-enable; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + conf-clk { + pins = "EMMC_CK"; + drive-strength = <6>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-ds { + pins = "EMMC_DSL"; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-rst { + pins = "EMMC_RSTB"; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + }; + + mmc0_pins_uhs: mmc0-uhs-pins { + mux { + function = "emmc"; + groups = "emmc_51"; + }; + conf-cmd-dat { + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; + input-enable; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + conf-clk { + pins = "EMMC_CK"; + drive-strength = <6>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-ds { + pins = "EMMC_DSL"; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-rst { + pins = "EMMC_RSTB"; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + }; + + pcie_pins: pcie-pins { + mux { + function = "pcie"; + groups = "pcie_clk", "pcie_pereset"; + }; + }; + + spi_flash_pins: spi-flash-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; + + spic_pins: spic-pins { + mux { + function = "spi"; + groups = "spi1_0"; + }; + }; + + uart1_pins: uart1-pins { + mux { + function = "uart"; + groups = "uart1_rx_tx"; + }; + }; + + uart2_pins: uart2-pins { + mux { + function = "uart"; + groups = "uart2_0_rx_tx"; + }; + }; + + wf_2g_5g_pins: wf-2g-5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_dbdc_pins: wf-dbdc-pins { + mux { + function = "wifi"; + groups = "wf_dbdc"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_led_pins: wf-led-pins { + mux { + function = "led"; + groups = "wifi_led"; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + cs-gpios = <0>, <0>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spic_pins>; + cs-gpios = <0>, <0>; + status = "okay"; +}; + +&ssusb { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "wan"; + }; + + port@1 { + reg = <1>; + label = "lan0"; + }; + + port@2 { + reg = <2>; + label = "lan1"; + }; + + port@3 { + reg = <3>; + label = "lan2"; + }; + + port@4 { + reg = <4>; + label = "lan3"; + }; + + port5: port@5 { + reg = <5>; + label = "lan4"; + phy-mode = "2500base-x"; + sfp = <&sfp2>; + managed = "in-band-status"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default", "dbdc"; + pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>; + pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>; +}; +
Add support for Bananapi R3 SBC. - SD/eMMC support (switching first 4 bits of data-bus with sw6/D) - all rj45 ports and both SFP working (eth1/lan4) - all USB-Ports + SIM-Slot tested - i2c and all uarts tested - wifi tested (with eeprom calibration data) Signed-off-by: Frank Wunderlich <frank-w@public-files.de> --- SPI-NAND/NOR switched (CS by sw5/C) not yet included this is done with DT-Overlays in my tree, don't know how to do it in upstream the right way...added dts files for dtbo and added them with dtbo extension to Makefile works. changes: v4: - add PCIe nodes - fix sfp-properties of sfp-1 (need to be plural) thx to Denis Odintsov for this v3: - rename factory-key to reset-key - add dcin regulator and add it as input for 3v3 (with renaming) - remove memory-node - dropped wifi eeprom (calibration) data - move mmc0 pinctrl to common dtsi and drop sdcard comment - change mmc pull-up/down to have generic bias-pull* v2: - remove pcie to be added later (discussion about clocks) - some fixes based on suggestions on ML - add key suffix like it's done in mt7622-bpi-r64 devicetree - add dash in sfp node names - use reg as unit for switch-node - drop "-3-4" suffix from i2c-pins node name - fix order in Makefile --- arch/arm64/boot/dts/mediatek/Makefile | 2 + .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts | 31 ++ .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts | 25 + .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 458 ++++++++++++++++++ 4 files changed, 516 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi -- 2.34.1