@@ -139,6 +139,24 @@ int dwc3_gadget_set_link_state(struct dwc3 *dwc, enum dwc3_link_state state)
return -ETIMEDOUT;
}
+static void dwc3_ep0_reset_state(struct dwc3 *dwc)
+{
+ unsigned int dir;
+
+ if (dwc->ep0state != EP0_SETUP_PHASE) {
+ dir = !!dwc->ep0_expect_in;
+ if (dwc->ep0state == EP0_DATA_PHASE)
+ dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
+ else
+ dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
+
+ dwc->eps[0]->trb_enqueue = 0;
+ dwc->eps[1]->trb_enqueue = 0;
+
+ dwc3_ep0_stall_and_restart(dwc);
+ }
+}
+
/**
* dwc3_ep_inc_trb - increment a trb index.
* @index: Pointer to the TRB index to increment.
@@ -2563,16 +2581,9 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
if (ret == 0) {
- unsigned int dir;
-
dev_warn(dwc->dev, "wait for SETUP phase timed out\n");
spin_lock_irqsave(&dwc->lock, flags);
- dir = !!dwc->ep0_expect_in;
- if (dwc->ep0state == EP0_DATA_PHASE)
- dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
- else
- dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
- dwc3_ep0_stall_and_restart(dwc);
+ dwc3_ep0_reset_state(dwc);
spin_unlock_irqrestore(&dwc->lock, flags);
}
}
@@ -3847,16 +3858,7 @@ static void dwc3_gadget_disconnect_interrupt(struct dwc3 *dwc)
dwc->setup_packet_pending = false;
usb_gadget_set_state(dwc->gadget, USB_STATE_NOTATTACHED);
- if (dwc->ep0state != EP0_SETUP_PHASE) {
- unsigned int dir;
-
- dir = !!dwc->ep0_expect_in;
- if (dwc->ep0state == EP0_DATA_PHASE)
- dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
- else
- dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
- dwc3_ep0_stall_and_restart(dwc);
- }
+ dwc3_ep0_reset_state(dwc);
}
static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
@@ -3910,20 +3912,7 @@ static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
* phase. So ensure that EP0 is in setup phase by issuing a stall
* and restart if EP0 is not in setup phase.
*/
- if (dwc->ep0state != EP0_SETUP_PHASE) {
- unsigned int dir;
-
- dir = !!dwc->ep0_expect_in;
- if (dwc->ep0state == EP0_DATA_PHASE)
- dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
- else
- dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
-
- dwc->eps[0]->trb_enqueue = 0;
- dwc->eps[1]->trb_enqueue = 0;
-
- dwc3_ep0_stall_and_restart(dwc);
- }
+ dwc3_ep0_reset_state(dwc);
/*
* In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
Several sequences utilize the same routine for forcing the control endpoint back into the SETUP phase. This is required, because those operations need to ensure that EP0 is back in the default state. Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> --- drivers/usb/dwc3/gadget.c | 53 ++++++++++++++++----------------------- 1 file changed, 21 insertions(+), 32 deletions(-)