@@ -762,6 +762,11 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd)
bh = 1;
}
+ /* Force to check port status */
+ if (ehci->has_ci_pec_bug && (status & STS_ERR)
+ && !(status & STS_PCD))
+ status |= STS_PCD;
+
/* complete the unlinking of some qh [4.15.2.3] */
if (status & STS_IAA) {
@@ -674,7 +674,8 @@ ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
if ((temp & mask) != 0 || test_bit(i, &ehci->port_c_suspend)
|| (ehci->reset_done[i] && time_after_eq(
- jiffies, ehci->reset_done[i]))) {
+ jiffies, ehci->reset_done[i]))
+ || ehci_has_ci_pec_bug(ehci, temp)) {
if (i < 7)
buf [0] |= 1 << (i + 1);
else
@@ -875,6 +876,13 @@ int ehci_hub_control(
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
+ if (ehci_has_ci_pec_bug(ehci, temp)) {
+ status |= USB_PORT_STAT_C_ENABLE << 16;
+ ehci_info(ehci,
+ "PE is cleared by HW port:%d PORTSC:%08x\n",
+ wIndex + 1, temp);
+ }
+
if ((temp & PORT_OCC) && (!ignore_oc && !ehci->spurious_oc)){
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
@@ -207,6 +207,7 @@ struct ehci_hcd { /* one per controller */
unsigned has_fsl_port_bug:1; /* FreeScale */
unsigned has_fsl_hs_errata:1; /* Freescale HS quirk */
unsigned has_fsl_susp_errata:1; /* NXP SUSP quirk */
+ unsigned has_ci_pec_bug:1; /* ChipIdea PEC bug */
unsigned big_endian_mmio:1;
unsigned big_endian_desc:1;
unsigned big_endian_capbase:1;
@@ -707,6 +708,15 @@ ehci_port_speed(struct ehci_hcd *ehci, unsigned int portsc)
*/
#define ehci_has_fsl_susp_errata(e) ((e)->has_fsl_susp_errata)
+/*
+ * Some Freescale/NXP processors using ChipIdea IP have a bug in which
+ * disabling the port (PE is cleared) does not cause PEC to be asserted
+ * when frame babble is detected.
+ */
+#define ehci_has_ci_pec_bug(e, portsc) \
+ ((e)->has_ci_pec_bug && ((e)->command & CMD_PSE) \
+ && !(portsc & PORT_PEC) && !(portsc & PORT_PE))
+
/*
* While most USB host controllers implement their registers in
* little-endian format, a minority (celleb companion chip) implement
Some NXP processor using chipidea IP has a bug when frame babble is detected. As per 4.15.1.1.1 Serial Bus Babble: A babble condition also exists if IN transaction is in progress at High-speed SOF2 point. This is called frame balle. The host controller must disable the port to which the frame babble is detected. The USB controller has disabled the port (PE cleared) and has asserted USBERRINT when frame babble is detected, but PEC is not asserted. Therefore, the SW didn't aware that port has been disabled. Then the SW keeps sending packets to this port, but all of the transfers will fail. This workaround will firstly assert PCD by SW when USBERRINT is detected and then judge whether port change has really occurred or not by polling roothub status. Because the PEC doesn't get asserted in our case, this patch will also assert it by SW when specific conditions are satisfied. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> --- drivers/usb/host/ehci-hcd.c | 5 +++++ drivers/usb/host/ehci-hub.c | 10 +++++++++- drivers/usb/host/ehci.h | 10 ++++++++++ 3 files changed, 24 insertions(+), 1 deletion(-)