diff mbox series

[v2,3/3] usb: dwc3: Add workaround for host mode VBUS glitch when boot

Message ID 20240121222428.3396428-4-Frank.Li@nxp.com (mailing list archive)
State Superseded
Headers show
Series USB: dwc: Add workaround for host mode VBUS glitch when boot | expand

Commit Message

Frank Li Jan. 21, 2024, 10:24 p.m. UTC
From: Ran Wang <ran.wang_1@nxp.com>

When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
(or its control signal) will be turned on immediately on related Root Hub
ports. Then, the VBUS is turned off for a little while(15us) when do xhci
reset (conducted by xhci driver) and back to normal finally, we can
observe a negative glitch of related signal happen.

This VBUS glitch might cause some USB devices enumeration fail if kernel
boot with them connected. Such as LS1012AFWRY/LS1043ARDB/LX2160AQDS
/LS1088ARDB with Kingston 16GB USB2.0/Kingston USB3.0/JetFlash Transcend
4GB USB2.0 drives. The fail cases include enumerated as full-speed device
or report wrong device descriptor, etc.

One SW workaround which can fix this is by programing all xhci PORTSC[PP]
to 0 to turn off VBUS immediately after setting host mode in DWC3 driver
(per signal measurement result, it will be too late to do it in
xhci-plat.c or xhci.c). Then, after xhci reset complete in xhci driver,
PORTSC[PP]s' value will back to 1 automatically and VBUS on at that time,
no glitch happen and normal enumeration process has no impact.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 drivers/usb/dwc3/core.c |  3 +++
 drivers/usb/dwc3/core.h |  2 ++
 drivers/usb/dwc3/host.c | 48 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 53 insertions(+)

Comments

Thinh Nguyen Jan. 23, 2024, 2:39 a.m. UTC | #1
On Sun, Jan 21, 2024, Frank Li wrote:
> From: Ran Wang <ran.wang_1@nxp.com>
> 
> When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
> (or its control signal) will be turned on immediately on related Root Hub
> ports. Then, the VBUS is turned off for a little while(15us) when do xhci
> reset (conducted by xhci driver) and back to normal finally, we can
> observe a negative glitch of related signal happen.
> 
> This VBUS glitch might cause some USB devices enumeration fail if kernel
> boot with them connected. Such as LS1012AFWRY/LS1043ARDB/LX2160AQDS
> /LS1088ARDB with Kingston 16GB USB2.0/Kingston USB3.0/JetFlash Transcend
> 4GB USB2.0 drives. The fail cases include enumerated as full-speed device
> or report wrong device descriptor, etc.
> 
> One SW workaround which can fix this is by programing all xhci PORTSC[PP]
> to 0 to turn off VBUS immediately after setting host mode in DWC3 driver
> (per signal measurement result, it will be too late to do it in
> xhci-plat.c or xhci.c). Then, after xhci reset complete in xhci driver,
> PORTSC[PP]s' value will back to 1 automatically and VBUS on at that time,
> no glitch happen and normal enumeration process has no impact.
> 
> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
> Reviewed-by: Peter Chen <peter.chen@nxp.com>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
>  drivers/usb/dwc3/core.c |  3 +++
>  drivers/usb/dwc3/core.h |  2 ++
>  drivers/usb/dwc3/host.c | 48 +++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 53 insertions(+)
> 
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 3e55838c00014..3b68e8e45b8b9 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -1626,6 +1626,9 @@ static void dwc3_get_properties(struct dwc3 *dwc)
>  	dwc->dis_split_quirk = device_property_read_bool(dev,
>  				"snps,dis-split-quirk");
>  
> +	dwc->host_vbus_glitches_quirk = device_property_read_bool(dev,
> +				"snps,host-vbus-glitches-quirk");
> +
>  	dwc->lpm_nyet_threshold = lpm_nyet_threshold;
>  	dwc->tx_de_emphasis = tx_de_emphasis;
>  
> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> index e3eea965e57bf..df544ec730d22 100644
> --- a/drivers/usb/dwc3/core.h
> +++ b/drivers/usb/dwc3/core.h
> @@ -1132,6 +1132,7 @@ struct dwc3_scratchpad_array {
>   *	2	- No de-emphasis
>   *	3	- Reserved
>   * @dis_metastability_quirk: set to disable metastability quirk.
> + * @host_vbus_glitches_quirk: set to avoid vbus glitch during xhci reset.
>   * @dis_split_quirk: set to disable split boundary.
>   * @wakeup_configured: set if the device is configured for remote wakeup.
>   * @suspended: set to track suspend event due to U3/L2.
> @@ -1353,6 +1354,7 @@ struct dwc3 {
>  	unsigned		tx_de_emphasis:2;
>  
>  	unsigned		dis_metastability_quirk:1;
> +	unsigned		host_vbus_glitches_quirk:1;
>  
>  	unsigned		dis_split_quirk:1;
>  	unsigned		async_callbacks:1;
> diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
> index 61f57fe5bb783..ee1ffe1500560 100644
> --- a/drivers/usb/dwc3/host.c
> +++ b/drivers/usb/dwc3/host.c
> @@ -11,6 +11,9 @@
>  #include <linux/of.h>
>  #include <linux/platform_device.h>
>  
> +#include "../host/xhci-port.h"
> +#include "../host/xhci-ext-caps.h"
> +#include "../host/xhci-caps.h"
>  #include "core.h"
>  
>  static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc,
> @@ -28,6 +31,44 @@ static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc,
>  		dwc->xhci_resources[1].name = name;
>  }
>  
> +#define XHCI_HCSPARAMS1		0x4
> +#define XHCI_PORTSC_BASE	0x400
> +
> +/*
> + * dwc3_power_off_all_roothub_ports - Power off all Root hub ports
> + * @dwc3: Pointer to our controller context structure
> + */
> +static void dwc3_power_off_all_roothub_ports(struct dwc3 *dwc)
> +{
> +	int i, port_num;
> +	u32 reg, op_regs_base, offset;

Minor nit: please help keep the same style of declaring variables in
separate lines and reversed christmas tree.

> +	void __iomem *xhci_regs;
> +
> +	/* xhci regs is not mapped yet, do it temperary here */
> +	if (dwc->xhci_resources[0].start) {
> +		xhci_regs = ioremap(dwc->xhci_resources[0].start, DWC3_XHCI_REGS_END);
> +		if (IS_ERR(xhci_regs)) {
> +			dev_err(dwc->dev, "Failed to ioremap xhci_regs\n");
> +			return;
> +		}
> +
> +		op_regs_base = HC_LENGTH(readl(xhci_regs));
> +		reg = readl(xhci_regs + XHCI_HCSPARAMS1);
> +		port_num = HCS_MAX_PORTS(reg);
> +
> +		for (i = 1; i <= port_num; i++) {
> +			offset = op_regs_base + XHCI_PORTSC_BASE + 0x10 * (i - 1);
> +			reg = readl(xhci_regs + offset);
> +			reg &= ~PORT_POWER;
> +			writel(reg, xhci_regs + offset);
> +		}
> +
> +		iounmap(xhci_regs);
> +	} else {
> +		dev_err(dwc->dev, "xhci base reg invalid\n");
> +	}
> +}
> +

Minor nit: please move this hunk on top including the new define macros
instead of placing in the middle of irq related functions.

>  static int dwc3_host_get_irq(struct dwc3 *dwc)
>  {
>  	struct platform_device	*dwc3_pdev = to_platform_device(dwc->dev);
> @@ -66,6 +107,13 @@ int dwc3_host_init(struct dwc3 *dwc)
>  	int			ret, irq;
>  	int			prop_idx = 0;
>  
> +	/*
> +	 * We have to power off all Root hub ports immediately after DWC3 set
> +	 * to host mode to avoid VBUS glitch happen when xhci get reset later.

Reword "We have to ..." to "Some platforms need to ... "

> +	 */
> +	if (dwc->host_vbus_glitches_quirk)
> +		dwc3_power_off_all_roothub_ports(dwc);
> +
>  	irq = dwc3_host_get_irq(dwc);
>  	if (irq < 0)
>  		return irq;
> -- 
> 2.34.1
> 

The rest looks fine to me.

Thanks,
Thinh
diff mbox series

Patch

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 3e55838c00014..3b68e8e45b8b9 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1626,6 +1626,9 @@  static void dwc3_get_properties(struct dwc3 *dwc)
 	dwc->dis_split_quirk = device_property_read_bool(dev,
 				"snps,dis-split-quirk");
 
+	dwc->host_vbus_glitches_quirk = device_property_read_bool(dev,
+				"snps,host-vbus-glitches-quirk");
+
 	dwc->lpm_nyet_threshold = lpm_nyet_threshold;
 	dwc->tx_de_emphasis = tx_de_emphasis;
 
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index e3eea965e57bf..df544ec730d22 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -1132,6 +1132,7 @@  struct dwc3_scratchpad_array {
  *	2	- No de-emphasis
  *	3	- Reserved
  * @dis_metastability_quirk: set to disable metastability quirk.
+ * @host_vbus_glitches_quirk: set to avoid vbus glitch during xhci reset.
  * @dis_split_quirk: set to disable split boundary.
  * @wakeup_configured: set if the device is configured for remote wakeup.
  * @suspended: set to track suspend event due to U3/L2.
@@ -1353,6 +1354,7 @@  struct dwc3 {
 	unsigned		tx_de_emphasis:2;
 
 	unsigned		dis_metastability_quirk:1;
+	unsigned		host_vbus_glitches_quirk:1;
 
 	unsigned		dis_split_quirk:1;
 	unsigned		async_callbacks:1;
diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
index 61f57fe5bb783..ee1ffe1500560 100644
--- a/drivers/usb/dwc3/host.c
+++ b/drivers/usb/dwc3/host.c
@@ -11,6 +11,9 @@ 
 #include <linux/of.h>
 #include <linux/platform_device.h>
 
+#include "../host/xhci-port.h"
+#include "../host/xhci-ext-caps.h"
+#include "../host/xhci-caps.h"
 #include "core.h"
 
 static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc,
@@ -28,6 +31,44 @@  static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc,
 		dwc->xhci_resources[1].name = name;
 }
 
+#define XHCI_HCSPARAMS1		0x4
+#define XHCI_PORTSC_BASE	0x400
+
+/*
+ * dwc3_power_off_all_roothub_ports - Power off all Root hub ports
+ * @dwc3: Pointer to our controller context structure
+ */
+static void dwc3_power_off_all_roothub_ports(struct dwc3 *dwc)
+{
+	int i, port_num;
+	u32 reg, op_regs_base, offset;
+	void __iomem *xhci_regs;
+
+	/* xhci regs is not mapped yet, do it temperary here */
+	if (dwc->xhci_resources[0].start) {
+		xhci_regs = ioremap(dwc->xhci_resources[0].start, DWC3_XHCI_REGS_END);
+		if (IS_ERR(xhci_regs)) {
+			dev_err(dwc->dev, "Failed to ioremap xhci_regs\n");
+			return;
+		}
+
+		op_regs_base = HC_LENGTH(readl(xhci_regs));
+		reg = readl(xhci_regs + XHCI_HCSPARAMS1);
+		port_num = HCS_MAX_PORTS(reg);
+
+		for (i = 1; i <= port_num; i++) {
+			offset = op_regs_base + XHCI_PORTSC_BASE + 0x10 * (i - 1);
+			reg = readl(xhci_regs + offset);
+			reg &= ~PORT_POWER;
+			writel(reg, xhci_regs + offset);
+		}
+
+		iounmap(xhci_regs);
+	} else {
+		dev_err(dwc->dev, "xhci base reg invalid\n");
+	}
+}
+
 static int dwc3_host_get_irq(struct dwc3 *dwc)
 {
 	struct platform_device	*dwc3_pdev = to_platform_device(dwc->dev);
@@ -66,6 +107,13 @@  int dwc3_host_init(struct dwc3 *dwc)
 	int			ret, irq;
 	int			prop_idx = 0;
 
+	/*
+	 * We have to power off all Root hub ports immediately after DWC3 set
+	 * to host mode to avoid VBUS glitch happen when xhci get reset later.
+	 */
+	if (dwc->host_vbus_glitches_quirk)
+		dwc3_power_off_all_roothub_ports(dwc);
+
 	irq = dwc3_host_get_irq(dwc);
 	if (irq < 0)
 		return irq;