new file mode 100644
@@ -0,0 +1,85 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* hc_capbase bitmasks */
+/* bits 7:0 - how long is the Capabilities register */
+#define HC_LENGTH(p) XHCI_HC_LENGTH(p)
+/* bits 31:16 */
+#define HC_VERSION(p) (((p) >> 16) & 0xffff)
+
+/* HCSPARAMS1 - hcs_params1 - bitmasks */
+/* bits 0:7, Max Device Slots */
+#define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff)
+#define HCS_SLOTS_MASK 0xff
+/* bits 8:18, Max Interrupters */
+#define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff)
+/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
+#define HCS_MAX_PORTS(p) (((p) >> 24) & 0x7f)
+
+/* HCSPARAMS2 - hcs_params2 - bitmasks */
+/* bits 0:3, frames or uframes that SW needs to queue transactions
+ * ahead of the HW to meet periodic deadlines */
+#define HCS_IST(p) (((p) >> 0) & 0xf)
+/* bits 4:7, max number of Event Ring segments */
+#define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
+/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
+/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
+/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
+#define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
+
+/* HCSPARAMS3 - hcs_params3 - bitmasks */
+/* bits 0:7, Max U1 to U0 latency for the roothub ports */
+#define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff)
+/* bits 16:31, Max U2 to U0 latency for the roothub ports */
+#define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff)
+
+/* HCCPARAMS - hcc_params - bitmasks */
+/* true: HC can use 64-bit address pointers */
+#define HCC_64BIT_ADDR(p) ((p) & (1 << 0))
+/* true: HC can do bandwidth negotiation */
+#define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1))
+/* true: HC uses 64-byte Device Context structures
+ * FIXME 64-byte context structures aren't supported yet.
+ */
+#define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2))
+/* true: HC has port power switches */
+#define HCC_PPC(p) ((p) & (1 << 3))
+/* true: HC has port indicators */
+#define HCS_INDICATOR(p) ((p) & (1 << 4))
+/* true: HC has Light HC Reset Capability */
+#define HCC_LIGHT_RESET(p) ((p) & (1 << 5))
+/* true: HC supports latency tolerance messaging */
+#define HCC_LTC(p) ((p) & (1 << 6))
+/* true: no secondary Stream ID Support */
+#define HCC_NSS(p) ((p) & (1 << 7))
+/* true: HC supports Stopped - Short Packet */
+#define HCC_SPC(p) ((p) & (1 << 9))
+/* true: HC has Contiguous Frame ID Capability */
+#define HCC_CFC(p) ((p) & (1 << 11))
+/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
+#define HCC_MAX_PSA(p) (1 << ((((p) >> 12) & 0xf) + 1))
+/* Extended Capabilities pointer from PCI base - section 5.3.6 */
+#define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p)
+
+#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
+
+/* db_off bitmask - bits 0:1 reserved */
+#define DBOFF_MASK (~0x3)
+
+/* run_regs_off bitmask - bits 0:4 reserved */
+#define RTSOFF_MASK (~0x1f)
+
+/* HCCPARAMS2 - hcc_params2 - bitmasks */
+/* true: HC supports U3 entry Capability */
+#define HCC2_U3C(p) ((p) & (1 << 0))
+/* true: HC supports Configure endpoint command Max exit latency too large */
+#define HCC2_CMC(p) ((p) & (1 << 1))
+/* true: HC supports Force Save context Capability */
+#define HCC2_FSC(p) ((p) & (1 << 2))
+/* true: HC supports Compliance Transition Capability */
+#define HCC2_CTC(p) ((p) & (1 << 3))
+/* true: HC support Large ESIT payload Capability > 48k */
+#define HCC2_LEC(p) ((p) & (1 << 4))
+/* true: HC support Configuration Information Capability */
+#define HCC2_CIC(p) ((p) & (1 << 5))
+/* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
+#define HCC2_ETC(p) ((p) & (1 << 6))
new file mode 100644
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
+/* true: device connected */
+#define PORT_CONNECT (1 << 0)
+/* true: port enabled */
+#define PORT_PE (1 << 1)
+/* bit 2 reserved and zeroed */
+/* true: port has an over-current condition */
+#define PORT_OC (1 << 3)
+/* true: port reset signaling asserted */
+#define PORT_RESET (1 << 4)
+/* Port Link State - bits 5:8
+ * A read gives the current link PM state of the port,
+ * a write with Link State Write Strobe set sets the link state.
+ */
+#define PORT_PLS_MASK (0xf << 5)
+#define XDEV_U0 (0x0 << 5)
+#define XDEV_U1 (0x1 << 5)
+#define XDEV_U2 (0x2 << 5)
+#define XDEV_U3 (0x3 << 5)
+#define XDEV_DISABLED (0x4 << 5)
+#define XDEV_RXDETECT (0x5 << 5)
+#define XDEV_INACTIVE (0x6 << 5)
+#define XDEV_POLLING (0x7 << 5)
+#define XDEV_RECOVERY (0x8 << 5)
+#define XDEV_HOT_RESET (0x9 << 5)
+#define XDEV_COMP_MODE (0xa << 5)
+#define XDEV_TEST_MODE (0xb << 5)
+#define XDEV_RESUME (0xf << 5)
+
+/* true: port has power (see HCC_PPC) */
+#define PORT_POWER (1 << 9)
+/* bits 10:13 indicate device speed:
+ * 0 - undefined speed - port hasn't be initialized by a reset yet
+ * 1 - full speed
+ * 2 - low speed
+ * 3 - high speed
+ * 4 - super speed
+ * 5-15 reserved
+ */
+#define DEV_SPEED_MASK (0xf << 10)
+#define XDEV_FS (0x1 << 10)
+#define XDEV_LS (0x2 << 10)
+#define XDEV_HS (0x3 << 10)
+#define XDEV_SS (0x4 << 10)
+#define XDEV_SSP (0x5 << 10)
+#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
+#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
+#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
+#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
+#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
+#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
+#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
+#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
+
+/* Bits 20:23 in the Slot Context are the speed for the device */
+#define SLOT_SPEED_FS (XDEV_FS << 10)
+#define SLOT_SPEED_LS (XDEV_LS << 10)
+#define SLOT_SPEED_HS (XDEV_HS << 10)
+#define SLOT_SPEED_SS (XDEV_SS << 10)
+#define SLOT_SPEED_SSP (XDEV_SSP << 10)
+/* Port Indicator Control */
+#define PORT_LED_OFF (0 << 14)
+#define PORT_LED_AMBER (1 << 14)
+#define PORT_LED_GREEN (2 << 14)
+#define PORT_LED_MASK (3 << 14)
+/* Port Link State Write Strobe - set this when changing link state */
+#define PORT_LINK_STROBE (1 << 16)
+/* true: connect status change */
+#define PORT_CSC (1 << 17)
+/* true: port enable change */
+#define PORT_PEC (1 << 18)
+/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
+ * into an enabled state, and the device into the default state. A "warm" reset
+ * also resets the link, forcing the device through the link training sequence.
+ * SW can also look at the Port Reset register to see when warm reset is done.
+ */
+#define PORT_WRC (1 << 19)
+/* true: over-current change */
+#define PORT_OCC (1 << 20)
+/* true: reset change - 1 to 0 transition of PORT_RESET */
+#define PORT_RC (1 << 21)
+/* port link status change - set on some port link state transitions:
+ * Transition Reason
+ * ------------------------------------------------------------------------------
+ * - U3 to Resume Wakeup signaling from a device
+ * - Resume to Recovery to U0 USB 3.0 device resume
+ * - Resume to U0 USB 2.0 device resume
+ * - U3 to Recovery to U0 Software resume of USB 3.0 device complete
+ * - U3 to U0 Software resume of USB 2.0 device complete
+ * - U2 to U0 L1 resume of USB 2.1 device complete
+ * - U0 to U0 (???) L1 entry rejection by USB 2.1 device
+ * - U0 to disabled L1 entry error with USB 2.1 device
+ * - Any state to inactive Error on USB 3.0 port
+ */
+#define PORT_PLC (1 << 22)
+/* port configure error change - port failed to configure its link partner */
+#define PORT_CEC (1 << 23)
+#define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
+ PORT_RC | PORT_PLC | PORT_CEC)
+
+
+/* Cold Attach Status - xHC can set this bit to report device attached during
+ * Sx state. Warm port reset should be perfomed to clear this bit and move port
+ * to connected state.
+ */
+#define PORT_CAS (1 << 24)
+/* wake on connect (enable) */
+#define PORT_WKCONN_E (1 << 25)
+/* wake on disconnect (enable) */
+#define PORT_WKDISC_E (1 << 26)
+/* wake on over-current (enable) */
+#define PORT_WKOC_E (1 << 27)
+/* bits 28:29 reserved */
+/* true: device is non-removable - for USB 3.0 roothub emulation */
+#define PORT_DEV_REMOVE (1 << 30)
+/* Initiate a warm port reset - complete when PORT_WRC is '1' */
+#define PORT_WR (1 << 31)
+
+/* We mark duplicate entries with -1 */
+#define DUPLICATE_ENTRY ((u8)(-1))
+
+/* Port Power Management Status and Control - port_power_base bitmasks */
+/* Inactivity timer value for transitions into U1, in microseconds.
+ * Timeout can be up to 127us. 0xFF means an infinite timeout.
+ */
+#define PORT_U1_TIMEOUT(p) ((p) & 0xff)
+#define PORT_U1_TIMEOUT_MASK 0xff
+/* Inactivity timer value for transitions into U2 */
+#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
+#define PORT_U2_TIMEOUT_MASK (0xff << 8)
+/* Bits 24:31 for port testing */
+
+/* USB2 Protocol PORTSPMSC */
+#define PORT_L1S_MASK 7
+#define PORT_L1S_SUCCESS 1
+#define PORT_RWE (1 << 3)
+#define PORT_HIRD(p) (((p) & 0xf) << 4)
+#define PORT_HIRD_MASK (0xf << 4)
+#define PORT_L1DS_MASK (0xff << 8)
+#define PORT_L1DS(p) (((p) & 0xff) << 8)
+#define PORT_HLE (1 << 16)
+#define PORT_TEST_MODE_SHIFT 28
+
+/* USB3 Protocol PORTLI Port Link Information */
+#define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
+#define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
+
+/* USB2 Protocol PORTHLPMC */
+#define PORT_HIRDM(p)((p) & 3)
+#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
+#define PORT_BESLD(p)(((p) & 0xf) << 10)
+
+/* use 512 microseconds as USB2 LPM L1 default timeout. */
+#define XHCI_L1_TIMEOUT 512
+
+/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
+ * Safe to use with mixed HIRD and BESL systems (host and device) and is used
+ * by other operating systems.
+ *
+ * XHCI 1.0 errata 8/14/12 Table 13 notes:
+ * "Software should choose xHC BESL/BESLD field values that do not violate a
+ * device's resume latency requirements,
+ * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
+ * or not program values < '4' if BLC = '0' and a BESL device is attached.
+ */
+#define XHCI_DEFAULT_BESL 4
+
+/*
+ * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
+ * to complete link training. usually link trainig completes much faster
+ * so check status 10 times with 36ms sleep in places we need to wait for
+ * polling to complete.
+ */
+#define XHCI_PORT_POLLING_LFPS_TIME 36
@@ -22,6 +22,9 @@
#include "xhci-ext-caps.h"
#include "pci-quirks.h"
+#include "xhci-port.h"
+#include "xhci-caps.h"
+
/* max buffer size for trace and debug messages */
#define XHCI_MSG_MAX 500
@@ -62,90 +65,6 @@ struct xhci_cap_regs {
/* Reserved up to (CAPLENGTH - 0x1C) */
};
-/* hc_capbase bitmasks */
-/* bits 7:0 - how long is the Capabilities register */
-#define HC_LENGTH(p) XHCI_HC_LENGTH(p)
-/* bits 31:16 */
-#define HC_VERSION(p) (((p) >> 16) & 0xffff)
-
-/* HCSPARAMS1 - hcs_params1 - bitmasks */
-/* bits 0:7, Max Device Slots */
-#define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff)
-#define HCS_SLOTS_MASK 0xff
-/* bits 8:18, Max Interrupters */
-#define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff)
-/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
-#define HCS_MAX_PORTS(p) (((p) >> 24) & 0x7f)
-
-/* HCSPARAMS2 - hcs_params2 - bitmasks */
-/* bits 0:3, frames or uframes that SW needs to queue transactions
- * ahead of the HW to meet periodic deadlines */
-#define HCS_IST(p) (((p) >> 0) & 0xf)
-/* bits 4:7, max number of Event Ring segments */
-#define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
-/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
-/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
-/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
-#define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
-
-/* HCSPARAMS3 - hcs_params3 - bitmasks */
-/* bits 0:7, Max U1 to U0 latency for the roothub ports */
-#define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff)
-/* bits 16:31, Max U2 to U0 latency for the roothub ports */
-#define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff)
-
-/* HCCPARAMS - hcc_params - bitmasks */
-/* true: HC can use 64-bit address pointers */
-#define HCC_64BIT_ADDR(p) ((p) & (1 << 0))
-/* true: HC can do bandwidth negotiation */
-#define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1))
-/* true: HC uses 64-byte Device Context structures
- * FIXME 64-byte context structures aren't supported yet.
- */
-#define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2))
-/* true: HC has port power switches */
-#define HCC_PPC(p) ((p) & (1 << 3))
-/* true: HC has port indicators */
-#define HCS_INDICATOR(p) ((p) & (1 << 4))
-/* true: HC has Light HC Reset Capability */
-#define HCC_LIGHT_RESET(p) ((p) & (1 << 5))
-/* true: HC supports latency tolerance messaging */
-#define HCC_LTC(p) ((p) & (1 << 6))
-/* true: no secondary Stream ID Support */
-#define HCC_NSS(p) ((p) & (1 << 7))
-/* true: HC supports Stopped - Short Packet */
-#define HCC_SPC(p) ((p) & (1 << 9))
-/* true: HC has Contiguous Frame ID Capability */
-#define HCC_CFC(p) ((p) & (1 << 11))
-/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
-#define HCC_MAX_PSA(p) (1 << ((((p) >> 12) & 0xf) + 1))
-/* Extended Capabilities pointer from PCI base - section 5.3.6 */
-#define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p)
-
-#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
-
-/* db_off bitmask - bits 0:1 reserved */
-#define DBOFF_MASK (~0x3)
-
-/* run_regs_off bitmask - bits 0:4 reserved */
-#define RTSOFF_MASK (~0x1f)
-
-/* HCCPARAMS2 - hcc_params2 - bitmasks */
-/* true: HC supports U3 entry Capability */
-#define HCC2_U3C(p) ((p) & (1 << 0))
-/* true: HC supports Configure endpoint command Max exit latency too large */
-#define HCC2_CMC(p) ((p) & (1 << 1))
-/* true: HC supports Force Save context Capability */
-#define HCC2_FSC(p) ((p) & (1 << 2))
-/* true: HC supports Compliance Transition Capability */
-#define HCC2_CTC(p) ((p) & (1 << 3))
-/* true: HC support Large ESIT payload Capability > 48k */
-#define HCC2_LEC(p) ((p) & (1 << 4))
-/* true: HC support Configuration Information Capability */
-#define HCC2_CIC(p) ((p) & (1 << 5))
-/* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
-#define HCC2_ETC(p) ((p) & (1 << 6))
-
/* Number of registers per port */
#define NUM_PORT_REGS 4
@@ -291,181 +210,6 @@ struct xhci_op_regs {
#define CONFIG_CIE (1 << 9)
/* bits 10:31 - reserved and should be preserved */
-/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
-/* true: device connected */
-#define PORT_CONNECT (1 << 0)
-/* true: port enabled */
-#define PORT_PE (1 << 1)
-/* bit 2 reserved and zeroed */
-/* true: port has an over-current condition */
-#define PORT_OC (1 << 3)
-/* true: port reset signaling asserted */
-#define PORT_RESET (1 << 4)
-/* Port Link State - bits 5:8
- * A read gives the current link PM state of the port,
- * a write with Link State Write Strobe set sets the link state.
- */
-#define PORT_PLS_MASK (0xf << 5)
-#define XDEV_U0 (0x0 << 5)
-#define XDEV_U1 (0x1 << 5)
-#define XDEV_U2 (0x2 << 5)
-#define XDEV_U3 (0x3 << 5)
-#define XDEV_DISABLED (0x4 << 5)
-#define XDEV_RXDETECT (0x5 << 5)
-#define XDEV_INACTIVE (0x6 << 5)
-#define XDEV_POLLING (0x7 << 5)
-#define XDEV_RECOVERY (0x8 << 5)
-#define XDEV_HOT_RESET (0x9 << 5)
-#define XDEV_COMP_MODE (0xa << 5)
-#define XDEV_TEST_MODE (0xb << 5)
-#define XDEV_RESUME (0xf << 5)
-
-/* true: port has power (see HCC_PPC) */
-#define PORT_POWER (1 << 9)
-/* bits 10:13 indicate device speed:
- * 0 - undefined speed - port hasn't be initialized by a reset yet
- * 1 - full speed
- * 2 - low speed
- * 3 - high speed
- * 4 - super speed
- * 5-15 reserved
- */
-#define DEV_SPEED_MASK (0xf << 10)
-#define XDEV_FS (0x1 << 10)
-#define XDEV_LS (0x2 << 10)
-#define XDEV_HS (0x3 << 10)
-#define XDEV_SS (0x4 << 10)
-#define XDEV_SSP (0x5 << 10)
-#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
-#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
-#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
-#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
-#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
-#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
-#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
-#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
-
-/* Bits 20:23 in the Slot Context are the speed for the device */
-#define SLOT_SPEED_FS (XDEV_FS << 10)
-#define SLOT_SPEED_LS (XDEV_LS << 10)
-#define SLOT_SPEED_HS (XDEV_HS << 10)
-#define SLOT_SPEED_SS (XDEV_SS << 10)
-#define SLOT_SPEED_SSP (XDEV_SSP << 10)
-/* Port Indicator Control */
-#define PORT_LED_OFF (0 << 14)
-#define PORT_LED_AMBER (1 << 14)
-#define PORT_LED_GREEN (2 << 14)
-#define PORT_LED_MASK (3 << 14)
-/* Port Link State Write Strobe - set this when changing link state */
-#define PORT_LINK_STROBE (1 << 16)
-/* true: connect status change */
-#define PORT_CSC (1 << 17)
-/* true: port enable change */
-#define PORT_PEC (1 << 18)
-/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
- * into an enabled state, and the device into the default state. A "warm" reset
- * also resets the link, forcing the device through the link training sequence.
- * SW can also look at the Port Reset register to see when warm reset is done.
- */
-#define PORT_WRC (1 << 19)
-/* true: over-current change */
-#define PORT_OCC (1 << 20)
-/* true: reset change - 1 to 0 transition of PORT_RESET */
-#define PORT_RC (1 << 21)
-/* port link status change - set on some port link state transitions:
- * Transition Reason
- * ------------------------------------------------------------------------------
- * - U3 to Resume Wakeup signaling from a device
- * - Resume to Recovery to U0 USB 3.0 device resume
- * - Resume to U0 USB 2.0 device resume
- * - U3 to Recovery to U0 Software resume of USB 3.0 device complete
- * - U3 to U0 Software resume of USB 2.0 device complete
- * - U2 to U0 L1 resume of USB 2.1 device complete
- * - U0 to U0 (???) L1 entry rejection by USB 2.1 device
- * - U0 to disabled L1 entry error with USB 2.1 device
- * - Any state to inactive Error on USB 3.0 port
- */
-#define PORT_PLC (1 << 22)
-/* port configure error change - port failed to configure its link partner */
-#define PORT_CEC (1 << 23)
-#define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
- PORT_RC | PORT_PLC | PORT_CEC)
-
-
-/* Cold Attach Status - xHC can set this bit to report device attached during
- * Sx state. Warm port reset should be perfomed to clear this bit and move port
- * to connected state.
- */
-#define PORT_CAS (1 << 24)
-/* wake on connect (enable) */
-#define PORT_WKCONN_E (1 << 25)
-/* wake on disconnect (enable) */
-#define PORT_WKDISC_E (1 << 26)
-/* wake on over-current (enable) */
-#define PORT_WKOC_E (1 << 27)
-/* bits 28:29 reserved */
-/* true: device is non-removable - for USB 3.0 roothub emulation */
-#define PORT_DEV_REMOVE (1 << 30)
-/* Initiate a warm port reset - complete when PORT_WRC is '1' */
-#define PORT_WR (1 << 31)
-
-/* We mark duplicate entries with -1 */
-#define DUPLICATE_ENTRY ((u8)(-1))
-
-/* Port Power Management Status and Control - port_power_base bitmasks */
-/* Inactivity timer value for transitions into U1, in microseconds.
- * Timeout can be up to 127us. 0xFF means an infinite timeout.
- */
-#define PORT_U1_TIMEOUT(p) ((p) & 0xff)
-#define PORT_U1_TIMEOUT_MASK 0xff
-/* Inactivity timer value for transitions into U2 */
-#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
-#define PORT_U2_TIMEOUT_MASK (0xff << 8)
-/* Bits 24:31 for port testing */
-
-/* USB2 Protocol PORTSPMSC */
-#define PORT_L1S_MASK 7
-#define PORT_L1S_SUCCESS 1
-#define PORT_RWE (1 << 3)
-#define PORT_HIRD(p) (((p) & 0xf) << 4)
-#define PORT_HIRD_MASK (0xf << 4)
-#define PORT_L1DS_MASK (0xff << 8)
-#define PORT_L1DS(p) (((p) & 0xff) << 8)
-#define PORT_HLE (1 << 16)
-#define PORT_TEST_MODE_SHIFT 28
-
-/* USB3 Protocol PORTLI Port Link Information */
-#define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
-#define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
-
-/* USB2 Protocol PORTHLPMC */
-#define PORT_HIRDM(p)((p) & 3)
-#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
-#define PORT_BESLD(p)(((p) & 0xf) << 10)
-
-/* use 512 microseconds as USB2 LPM L1 default timeout. */
-#define XHCI_L1_TIMEOUT 512
-
-/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
- * Safe to use with mixed HIRD and BESL systems (host and device) and is used
- * by other operating systems.
- *
- * XHCI 1.0 errata 8/14/12 Table 13 notes:
- * "Software should choose xHC BESL/BESLD field values that do not violate a
- * device's resume latency requirements,
- * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
- * or not program values < '4' if BLC = '0' and a BESL device is attached.
- */
-#define XHCI_DEFAULT_BESL 4
-
-/*
- * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
- * to complete link training. usually link trainig completes much faster
- * so check status 10 times with 36ms sleep in places we need to wait for
- * polling to complete.
- */
-#define XHCI_PORT_POLLING_LFPS_TIME 36
-
/**
* struct xhci_intr_reg - Interrupt Register Set
* @irq_pending: IMAN - Interrupt Management Register. Used to enable
Split the PORT and CAPs macro definitions into a separate file to facilitate sharing with other files without the need to include the entire xhci.h. Signed-off-by: Frank Li <Frank.Li@nxp.com> --- drivers/usb/host/xhci-caps.h | 85 ++++++++++++ drivers/usb/host/xhci-port.h | 176 +++++++++++++++++++++++ drivers/usb/host/xhci.h | 262 +---------------------------------- 3 files changed, 264 insertions(+), 259 deletions(-) create mode 100644 drivers/usb/host/xhci-caps.h create mode 100644 drivers/usb/host/xhci-port.h