@@ -1221,7 +1221,7 @@ static void nhi_check_iommu(struct tb_nhi *nhi)
str_enabled_disabled(port_ok));
}
-static bool nhi_reset(struct tb_nhi *nhi)
+static void nhi_reset(struct tb_nhi *nhi)
{
ktime_t timeout;
u32 val;
@@ -1229,11 +1229,11 @@ static bool nhi_reset(struct tb_nhi *nhi)
val = ioread32(nhi->iobase + REG_CAPS);
/* Reset only v2 and later routers */
if (FIELD_GET(REG_CAPS_VERSION_MASK, val) < REG_CAPS_VERSION_2)
- return false;
+ return;
if (!host_reset) {
dev_dbg(&nhi->pdev->dev, "skipping host router reset\n");
- return false;
+ return;
}
iowrite32(REG_RESET_HRR, nhi->iobase + REG_RESET);
@@ -1244,14 +1244,12 @@ static bool nhi_reset(struct tb_nhi *nhi)
val = ioread32(nhi->iobase + REG_RESET);
if (!(val & REG_RESET_HRR)) {
dev_warn(&nhi->pdev->dev, "host router reset successful\n");
- return true;
+ return;
}
usleep_range(10, 20);
} while (ktime_before(ktime_get(), timeout));
dev_warn(&nhi->pdev->dev, "timeout resetting host router\n");
-
- return false;
}
static int nhi_init_msi(struct tb_nhi *nhi)
@@ -1333,7 +1331,6 @@ static int nhi_probe(struct pci_dev *pdev, const struct pci_device_id *id)
struct device *dev = &pdev->dev;
struct tb_nhi *nhi;
struct tb *tb;
- bool reset;
int res;
if (!nhi_imr_valid(pdev))
@@ -1367,12 +1364,7 @@ static int nhi_probe(struct pci_dev *pdev, const struct pci_device_id *id)
nhi_check_quirks(nhi);
nhi_check_iommu(nhi);
-
- /*
- * Only USB4 v2 hosts support host reset so if we already did
- * that then don't do it again when the domain is initialized.
- */
- reset = nhi_reset(nhi) ? false : host_reset;
+ nhi_reset(nhi);
res = nhi_init_msi(nhi);
if (res)
@@ -1399,7 +1391,7 @@ static int nhi_probe(struct pci_dev *pdev, const struct pci_device_id *id)
dev_dbg(dev, "NHI initialized, starting thunderbolt\n");
- res = tb_domain_add(tb, reset);
+ res = tb_domain_add(tb, host_reset);
if (res) {
/*
* At this point the RX/TX rings might already have been
@@ -2584,6 +2584,7 @@ static int tb_scan_finalize_switch(struct device *dev, void *data)
static int tb_start(struct tb *tb, bool reset)
{
struct tb_cm *tcm = tb_priv(tb);
+ bool discover = true;
int ret;
tb->root_switch = tb_switch_alloc(tb, &tb->dev, 0);
@@ -2629,9 +2630,13 @@ static int tb_start(struct tb *tb, bool reset)
* reset the ports to handle it as new hotplug for USB4 v1
* routers (for USB4 v2 and beyond we already do host reset).
*/
- if (reset && usb4_switch_version(tb->root_switch) == 1) {
- tb_switch_reset(tb->root_switch);
- } else {
+ if (reset && tb_switch_is_usb4(tb->root_switch)) {
+ discover = false;
+ if (usb4_switch_version(tb->root_switch) == 1)
+ tb_switch_reset(tb->root_switch);
+ }
+
+ if (discover) {
/* Full scan to discover devices added before the driver was loaded. */
tb_scan_switch(tb->root_switch);
/* Find out tunnels created by the boot firmware */
If the host router is reset, there is no point running discovery as the links are down. Furthermore this prevents CL-state enabling. For this reason skip discovery in USB4 v2 host the same way we do with USB4 v1. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> --- drivers/thunderbolt/nhi.c | 20 ++++++-------------- drivers/thunderbolt/tb.c | 11 ++++++++--- 2 files changed, 14 insertions(+), 17 deletions(-)