@@ -67,6 +67,18 @@ static int tcpci_write16(struct tcpci *tcpci, unsigned int reg, u16 val)
return regmap_raw_write(tcpci->regmap, reg, &val, sizeof(u16));
}
+static bool tcpci_check_std_output_cap(struct regmap *regmap, u8 mask)
+{
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(regmap, TCPC_STD_OUTPUT_CAP, ®);
+ if (ret < 0)
+ return ret;
+
+ return (reg & mask) == mask;
+}
+
static int tcpci_set_cc(struct tcpc_dev *tcpc, enum typec_cc_status cc)
{
struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
@@ -301,6 +313,28 @@ static int tcpci_set_polarity(struct tcpc_dev *tcpc,
TCPC_TCPC_CTRL_ORIENTATION : 0);
}
+static int tcpci_set_orientation(struct tcpc_dev *tcpc,
+ enum typec_orientation orientation)
+{
+ struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
+ unsigned int reg;
+
+ switch (orientation) {
+ case TYPEC_ORIENTATION_NONE:
+ /* We can't put a single output into high impedance */
+ fallthrough;
+ case TYPEC_ORIENTATION_NORMAL:
+ reg = TCPC_CONFIG_STD_OUTPUT_ORIENTATION_NORMAL;
+ break;
+ case TYPEC_ORIENTATION_REVERSE:
+ reg = TCPC_CONFIG_STD_OUTPUT_ORIENTATION_FLIPPED;
+ break;
+ }
+
+ return regmap_update_bits(tcpci->regmap, TCPC_CONFIG_STD_OUTPUT,
+ TCPC_CONFIG_STD_OUTPUT_ORIENTATION_MASK, reg);
+}
+
static void tcpci_set_partner_usb_comm_capable(struct tcpc_dev *tcpc, bool capable)
{
struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
@@ -808,6 +842,9 @@ struct tcpci *tcpci_register_port(struct device *dev, struct tcpci_data *data)
if (tcpci->data->vbus_vsafe0v)
tcpci->tcpc.is_vbus_vsafe0v = tcpci_is_vbus_vsafe0v;
+ if (tcpci->data->set_orientation)
+ tcpci->tcpc.set_orientation = tcpci_set_orientation;
+
err = tcpci_parse_config(tcpci);
if (err < 0)
return ERR_PTR(err);
@@ -851,6 +888,13 @@ static int tcpci_probe(struct i2c_client *client)
if (err < 0)
return err;
+ err = tcpci_check_std_output_cap(chip->data.regmap,
+ TCPC_STD_OUTPUT_CAP_ORIENTATION);
+ if (err < 0)
+ return err;
+
+ chip->data.set_orientation = err;
+
chip->tcpci = tcpci_register_port(&client->dev, &chip->data);
if (IS_ERR(chip->tcpci))
return PTR_ERR(chip->tcpci);
@@ -47,6 +47,9 @@
#define TCPC_SINK_FAST_ROLE_SWAP BIT(0)
#define TCPC_CONFIG_STD_OUTPUT 0x18
+#define TCPC_CONFIG_STD_OUTPUT_ORIENTATION_MASK BIT(0)
+#define TCPC_CONFIG_STD_OUTPUT_ORIENTATION_NORMAL 0
+#define TCPC_CONFIG_STD_OUTPUT_ORIENTATION_FLIPPED 1
#define TCPC_TCPC_CTRL 0x19
#define TCPC_TCPC_CTRL_ORIENTATION BIT(0)
@@ -127,6 +130,7 @@
#define TCPC_DEV_CAP_2 0x26
#define TCPC_STD_INPUT_CAP 0x28
#define TCPC_STD_OUTPUT_CAP 0x29
+#define TCPC_STD_OUTPUT_CAP_ORIENTATION BIT(0)
#define TCPC_MSG_HDR_INFO 0x2e
#define TCPC_MSG_HDR_INFO_DATA_ROLE BIT(3)
@@ -198,12 +202,16 @@ struct tcpci;
* Chip level drivers are expected to check for contaminant and call
* tcpm_clean_port when the port is clean to put the port back into
* toggling state.
+ * @set_orientation:
+ * Optional; Enable setting the connector orientation
+ * CONFIG_STANDARD_OUTPUT (0x18) bit0.
*/
struct tcpci_data {
struct regmap *regmap;
unsigned char TX_BUF_BYTE_x_hidden:1;
unsigned char auto_discharge_disconnect:1;
unsigned char vbus_vsafe0v:1;
+ unsigned char set_orientation:1;
int (*init)(struct tcpci *tcpci, struct tcpci_data *data);
int (*set_vconn)(struct tcpci *tcpci, struct tcpci_data *data,
This add the support to set the optional connector orientation bit which is part of the optional CONFIG_STANDARD_OUTPUT register 0x18 [1]. This allows system designers to connect the tcpc orientation pin directly to the 2:1 ss-mux. [1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> --- v2: - Make use of fallthrough drivers/usb/typec/tcpm/tcpci.c | 44 ++++++++++++++++++++++++++++++++++ include/linux/usb/tcpci.h | 8 +++++++ 2 files changed, 52 insertions(+)