diff mbox series

[2/2] arm64: dts: qcom: x1e80100: Add USB Multiport controller

Message ID 20240809-topic-h_mp-v1-2-3c5f468566d8@quicinc.com (mailing list archive)
State Superseded
Headers show
Series X1E80100 multiport USB controller | expand

Commit Message

Konrad Dybcio Aug. 9, 2024, 1:18 p.m. UTC
X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
attached to it. It's commonly used for USB-A ports and internally
routed devices. Configure it to support such functionality.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 170 +++++++++++++++++++++++++++++++++
 1 file changed, 170 insertions(+)

Comments

Krzysztof Kozlowski Aug. 10, 2024, 12:48 p.m. UTC | #1
On 09/08/2024 15:18, Konrad Dybcio wrote:
> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
> attached to it. It's commonly used for USB-A ports and internally
> routed devices. Configure it to support such functionality.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>

You have from and SoB mismatch. This was sent some odd way, because both
b4 and git send-email would produce correct From field.


Best regards,
Krzysztof
Konrad Dybcio Aug. 13, 2024, 2:09 p.m. UTC | #2
On 10.08.2024 2:48 PM, Krzysztof Kozlowski wrote:
> On 09/08/2024 15:18, Konrad Dybcio wrote:
>> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
>> attached to it. It's commonly used for USB-A ports and internally
>> routed devices. Configure it to support such functionality.
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> 
> You have from and SoB mismatch. This was sent some odd way, because both
> b4 and git send-email would produce correct From field.

So, I'm:

- sending from @kernel because it has a good email server
- authoring from @quicinc because that's my employer
- sending some older @linaro patches because I made them before
  switching jobs and it's only fair to do so like this
(and I sometimes reply from @gmail because thunderbird works funnily)

I noticed locally that if you switch emails & edit author too often, git
gets confused and `git show` Author: / `git send` From: don't get updated
properly, but if you do git format-patch, the resulting file has what you
would expect..

Should I resend this?

Konrad
Krzysztof Kozlowski Aug. 13, 2024, 2:35 p.m. UTC | #3
On 13/08/2024 16:09, Konrad Dybcio wrote:
> On 10.08.2024 2:48 PM, Krzysztof Kozlowski wrote:
>> On 09/08/2024 15:18, Konrad Dybcio wrote:
>>> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
>>> attached to it. It's commonly used for USB-A ports and internally
>>> routed devices. Configure it to support such functionality.
>>>
>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>
>> You have from and SoB mismatch. This was sent some odd way, because both
>> b4 and git send-email would produce correct From field.
> 
> So, I'm:
> 
> - sending from @kernel because it has a good email server
> - authoring from @quicinc because that's my employer
> - sending some older @linaro patches because I made them before
>   switching jobs and it's only fair to do so like this
> (and I sometimes reply from @gmail because thunderbird works funnily)

This is all fine, but you created commit with one identity and signed
off with other. That's not fine.

> 
> I noticed locally that if you switch emails & edit author too often, git
> gets confused and `git show` Author: / `git send` From: don't get updated
> properly, but if you do git format-patch, the resulting file has what you
> would expect..
> 
> Should I resend this?

Yes, so there will be proper From field with proper author matching at
least one SoBs.

Best regards,
Krzysztof
Konrad Dybcio Aug. 13, 2024, 3:21 p.m. UTC | #4
On 13.08.2024 4:35 PM, Krzysztof Kozlowski wrote:
> On 13/08/2024 16:09, Konrad Dybcio wrote:
>> On 10.08.2024 2:48 PM, Krzysztof Kozlowski wrote:
>>> On 09/08/2024 15:18, Konrad Dybcio wrote:
>>>> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
>>>> attached to it. It's commonly used for USB-A ports and internally
>>>> routed devices. Configure it to support such functionality.
>>>>
>>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>>
>>> You have from and SoB mismatch. This was sent some odd way, because both
>>> b4 and git send-email would produce correct From field.
>>
>> So, I'm:
>>
>> - sending from @kernel because it has a good email server
>> - authoring from @quicinc because that's my employer
>> - sending some older @linaro patches because I made them before
>>   switching jobs and it's only fair to do so like this
>> (and I sometimes reply from @gmail because thunderbird works funnily)
> 
> This is all fine, but you created commit with one identity and signed
> off with other. That's not fine.
> 
>>
>> I noticed locally that if you switch emails & edit author too often, git
>> gets confused and `git show` Author: / `git send` From: don't get updated
>> properly, but if you do git format-patch, the resulting file has what you
>> would expect..
>>
>> Should I resend this?
> 
> Yes, so there will be proper From field with proper author matching at
> least one SoBs.

OK I know why it happens.. since my linaro address is in .mailmap, I can't
do any new git operations with it.. Removing it "fixes" it.. but then b4
base-commit needs to be altered..

Konrad
Konrad Dybcio Aug. 14, 2024, 10:24 a.m. UTC | #5
On 14.08.2024 12:08 PM, Song Xue wrote:
> 
> On 8/9/2024 9:18 PM, Konrad Dybcio wrote:
>> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
>> attached to it. It's commonly used for USB-A ports and internally
>> routed devices. Configure it to support such functionality.
>>
>> Signed-off-by: Konrad Dybcio<konrad.dybcio@linaro.org>
>> ---

[...]

>> +
>> +                phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>,
>> +                       <&usb_mp_hsphy1>, <&usb_mp_qmpphy1>;
>> +                phy-names = "usb2-0", "usb3-0",
>> +                        "usb2-1", "usb3-1";
>> +                dr_mode = "host";
> 
> Why do we add the dr_mode definition in dtsi file rather than in corresponding board dts file?  Could we follow the node "usb_1_ss1_dwc3"  in x1e80100-crd.dtsi?

That is because the MP controller is host-only and it doesn't make sense
to ensure the OS of that in each board file separately. That's also how
it's done on other platforms with a MP controller description.

> 
> BTW, how do we verify the function of  multiport controller?From my test on x1e80100-crd,  the eusb6 which is from usb_mp_hsphy1 attaches the third-party repeater, do we need a new repeater node/driver to verify the function of eusb6?

I have a X1E Surface Laptop 7 with a USB-A port with a NXP PTN3222 in
front of it. Tested with a smoke test, with both SS and HS USB-A devices.

Konrad
Song Xue Aug. 14, 2024, 11:56 a.m. UTC | #6
On 8/14/2024 6:24 PM, Konrad Dybcio wrote:
> On 14.08.2024 12:08 PM, Song Xue wrote:
>>
>> On 8/9/2024 9:18 PM, Konrad Dybcio wrote:
>>> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
>>> attached to it. It's commonly used for USB-A ports and internally
>>> routed devices. Configure it to support such functionality.
>>>
>>> Signed-off-by: Konrad Dybcio<konrad.dybcio@linaro.org>
>>> ---
> 
> [...]
> 
>>> +
>>> +                phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>,
>>> +                       <&usb_mp_hsphy1>, <&usb_mp_qmpphy1>;
>>> +                phy-names = "usb2-0", "usb3-0",
>>> +                        "usb2-1", "usb3-1";
>>> +                dr_mode = "host";
>>
>> Why do we add the dr_mode definition in dtsi file rather than in corresponding board dts file?  Could we follow the node "usb_1_ss1_dwc3"  in x1e80100-crd.dtsi?
> 
> That is because the MP controller is host-only and it doesn't make sense
> to ensure the OS of that in each board file separately. That's also how
> it's done on other platforms with a MP controller description.
> 
>>
>> BTW, how do we verify the function of  multiport controller?From my test on x1e80100-crd,  the eusb6 which is from usb_mp_hsphy1 attaches the third-party repeater, do we need a new repeater node/driver to verify the function of eusb6?
> 
> I have a X1E Surface Laptop 7 with a USB-A port with a NXP PTN3222 in
> front of it. Tested with a smoke test, with both SS and HS USB-A devices.
> 
What is detailed information on smoke test.
 From my end, I also have two questions.
1. I found the usb_mp_hsphy1 is using the driver "phy-qcom-snps-eusb2". 
However, the driver requires a repeater node from DT. At present, we 
don't have the node or driver for NXP repeater and it is not working on 
eusb6 to detect the NXP repeater. So, is it possible for us to have 
complete function involving with MP DT and repeater node for CRD board, 
and then we push patches together?
2. The usb_mp_dwc3 node has four phys. When enabling the driver for the 
node, we must need enable all four phys in borad's DT. Howerver, if the 
board is only using one phy like eusb6, is it suitable to enable other 
three phys?

Regards,
Song Xue
> Konrad
Konrad Dybcio Aug. 17, 2024, 11:32 a.m. UTC | #7
On 14.08.2024 1:56 PM, Song Xue wrote:
> 
> 
> On 8/14/2024 6:24 PM, Konrad Dybcio wrote:
>> On 14.08.2024 12:08 PM, Song Xue wrote:
>>>
>>> On 8/9/2024 9:18 PM, Konrad Dybcio wrote:
>>>> X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
>>>> attached to it. It's commonly used for USB-A ports and internally
>>>> routed devices. Configure it to support such functionality.
>>>>
>>>> Signed-off-by: Konrad Dybcio<konrad.dybcio@linaro.org>
>>>> ---
>>
>> [...]
>>
>>>> +
>>>> +                phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>,
>>>> +                       <&usb_mp_hsphy1>, <&usb_mp_qmpphy1>;
>>>> +                phy-names = "usb2-0", "usb3-0",
>>>> +                        "usb2-1", "usb3-1";
>>>> +                dr_mode = "host";
>>>
>>> Why do we add the dr_mode definition in dtsi file rather than in corresponding board dts file?  Could we follow the node "usb_1_ss1_dwc3"  in x1e80100-crd.dtsi?
>>
>> That is because the MP controller is host-only and it doesn't make sense
>> to ensure the OS of that in each board file separately. That's also how
>> it's done on other platforms with a MP controller description.
>>
>>>
>>> BTW, how do we verify the function of  multiport controller?From my test on x1e80100-crd,  the eusb6 which is from usb_mp_hsphy1 attaches the third-party repeater, do we need a new repeater node/driver to verify the function of eusb6?
>>
>> I have a X1E Surface Laptop 7 with a USB-A port with a NXP PTN3222 in
>> front of it. Tested with a smoke test, with both SS and HS USB-A devices.
>>
> What is detailed information on smoke test.
> From my end, I also have two questions.
> 1. I found the usb_mp_hsphy1 is using the driver "phy-qcom-snps-eusb2". However, the driver requires a repeater node from DT. At present, we don't have the node or driver for NXP repeater and it is not working on eusb6 to detect the NXP repeater. So, is it possible for us to have complete function involving with MP DT and repeater node for CRD board, and then we push patches together?

I believe you're a bit confused about the upstreaming process. Describing
hardware in Device Tree vs doing the same plus enabling it on some upstream
board are of equal value, and this patch is very much in the spirit of
"release early, release often".

There's no need to delay patches that are correct within their own
confinement (which they should be [1]) just so that the series is bigger.
That may even be discouraged by some folks..

> 2. The usb_mp_dwc3 node has four phys. When enabling the driver for the node, we must need enable all four phys in borad's DT. Howerver, if the board is only using one phy like eusb6, is it suitable to enable other three phys?

Yes, they will simply be registered, configured and since there won't
be any interrupts (as the pins are N/C, it will not do much). But
these PHYs are physically on the SoC regardless of them being
connected, so I see no issue.

[1] https://www.kernel.org/doc/html/latest/process/submitting-patches.html#separate-your-changes

Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 326283822aee..b6dd2f47341b 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -3842,6 +3842,90 @@  usb_2_hsphy: phy@88e0000 {
 			status = "disabled";
 		};
 
+		usb_mp_hsphy0: phy@88e1000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x088e1000 0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB3_MP0_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_HS0_MP_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_mp_hsphy1: phy@88e2000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x088e2000 0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB3_MP1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_HS1_MP_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_mp_qmpphy0: phy@88e3000 {
+			compatible = "qcom,x1e80100-qmp-usb3-uni-phy";
+			reg = <0 0x088e3000 0 0x2000>;
+
+			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "com_aux",
+				      "pipe";
+
+			resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>,
+				 <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>;
+			reset-names = "phy",
+				      "phy_phy";
+
+			power-domains = <&gcc GCC_USB3_MP_SS0_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "usb_mp_phy0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_mp_qmpphy1: phy@88e5000 {
+			compatible = "qcom,x1e80100-qmp-usb3-uni-phy";
+			reg = <0 0x088e5000 0 0x2000>;
+
+			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_PIPE_1_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "com_aux",
+				      "pipe";
+
+			resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>,
+				 <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>;
+			reset-names = "phy",
+				      "phy_phy";
+
+			power-domains = <&gcc GCC_USB3_MP_SS1_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "usb_mp_phy1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		usb_1_ss2: usb@a0f8800 {
 			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
 			reg = <0 0x0a0f8800 0 0x400>;
@@ -4016,6 +4100,92 @@  usb_2_dwc3_hs: endpoint {
 			};
 		};
 
+		usb_mp: usb@a4f8800 {
+			compatible = "qcom,x1e80100-dwc3-mp", "qcom,dwc3";
+			reg = <0 0x0a4f8800 0 0x400>;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
+				 <&gcc GCC_USB30_MP_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
+				 <&gcc GCC_USB30_MP_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "noc_aggr",
+				      "noc_aggr_north",
+				      "noc_aggr_south",
+				      "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MP_MASTER_CLK>;
+			assigned-clock-rates = <19200000>,
+					       <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 52 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 51 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 54 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 53 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 55 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 56 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event_1", "pwr_event_2",
+					  "hs_phy_1",	 "hs_phy_2",
+					  "dp_hs_phy_1", "dm_hs_phy_1",
+					  "dp_hs_phy_2", "dm_hs_phy_2",
+					  "ss_phy_1",	 "ss_phy_2";
+
+			power-domains = <&gcc GCC_USB30_MP_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_MP_BCR>;
+
+			interconnects = <&usb_north_anoc MASTER_USB3_MP QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_USB3_MP QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "usb-ddr",
+					     "apps-usb";
+
+			wakeup-source;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			usb_mp_dwc3: usb@a400000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a400000 0 0xcd00>;
+
+				interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+
+				iommus = <&apps_smmu 0x1400 0x0>;
+
+				phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>,
+				       <&usb_mp_hsphy1>, <&usb_mp_qmpphy1>;
+				phy-names = "usb2-0", "usb3-0",
+					    "usb2-1", "usb3-1";
+				dr_mode = "host";
+
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+
+				dma-coherent;
+			};
+		};
+
 		usb_1_ss0: usb@a6f8800 {
 			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
 			reg = <0 0x0a6f8800 0 0x400>;