@@ -25,73 +25,73 @@ struct xr_txrx_clk_mask {
};
#define XR_INT_OSC_HZ 48000000U
-#define XR21V141X_MIN_SPEED 46U
-#define XR21V141X_MAX_SPEED XR_INT_OSC_HZ
+#define MIN_SPEED 46U
+#define MAX_SPEED XR_INT_OSC_HZ
/* USB Requests */
-#define XR21V141X_SET_REQ 0
-#define XR21V141X_GET_REQ 1
-
-#define XR21V141X_CLOCK_DIVISOR_0 0x04
-#define XR21V141X_CLOCK_DIVISOR_1 0x05
-#define XR21V141X_CLOCK_DIVISOR_2 0x06
-#define XR21V141X_TX_CLOCK_MASK_0 0x07
-#define XR21V141X_TX_CLOCK_MASK_1 0x08
-#define XR21V141X_RX_CLOCK_MASK_0 0x09
-#define XR21V141X_RX_CLOCK_MASK_1 0x0a
-
-/* XR21V141X register blocks */
-#define XR21V141X_UART_REG_BLOCK 0
-#define XR21V141X_UM_REG_BLOCK 4
-#define XR21V141X_UART_CUSTOM_BLOCK 0x66
-
-/* XR21V141X UART Manager Registers */
-#define XR21V141X_UM_FIFO_ENABLE_REG 0x10
-#define XR21V141X_UM_ENABLE_TX_FIFO 0x01
-#define XR21V141X_UM_ENABLE_RX_FIFO 0x02
-
-#define XR21V141X_UM_RX_FIFO_RESET 0x18
-#define XR21V141X_UM_TX_FIFO_RESET 0x1c
-
-#define XR21V141X_UART_ENABLE_TX 0x1
-#define XR21V141X_UART_ENABLE_RX 0x2
-
-#define XR21V141X_UART_MODE_RI BIT(0)
-#define XR21V141X_UART_MODE_CD BIT(1)
-#define XR21V141X_UART_MODE_DSR BIT(2)
-#define XR21V141X_UART_MODE_DTR BIT(3)
-#define XR21V141X_UART_MODE_CTS BIT(4)
-#define XR21V141X_UART_MODE_RTS BIT(5)
-
-#define XR21V141X_UART_BREAK_ON 0xff
-#define XR21V141X_UART_BREAK_OFF 0
-
-#define XR21V141X_UART_DATA_MASK GENMASK(3, 0)
-#define XR21V141X_UART_DATA_7 0x7
-#define XR21V141X_UART_DATA_8 0x8
-
-#define XR21V141X_UART_PARITY_MASK GENMASK(6, 4)
-#define XR21V141X_UART_PARITY_SHIFT 4
-#define XR21V141X_UART_PARITY_NONE (0x0 << XR21V141X_UART_PARITY_SHIFT)
-#define XR21V141X_UART_PARITY_ODD (0x1 << XR21V141X_UART_PARITY_SHIFT)
-#define XR21V141X_UART_PARITY_EVEN (0x2 << XR21V141X_UART_PARITY_SHIFT)
-#define XR21V141X_UART_PARITY_MARK (0x3 << XR21V141X_UART_PARITY_SHIFT)
-#define XR21V141X_UART_PARITY_SPACE (0x4 << XR21V141X_UART_PARITY_SHIFT)
-
-#define XR21V141X_UART_STOP_MASK BIT(7)
-#define XR21V141X_UART_STOP_SHIFT 7
-#define XR21V141X_UART_STOP_1 (0x0 << XR21V141X_UART_STOP_SHIFT)
-#define XR21V141X_UART_STOP_2 (0x1 << XR21V141X_UART_STOP_SHIFT)
-
-#define XR21V141X_UART_FLOW_MODE_NONE 0x0
-#define XR21V141X_UART_FLOW_MODE_HW 0x1
-#define XR21V141X_UART_FLOW_MODE_SW 0x2
-
-#define XR21V141X_UART_MODE_GPIO_MASK GENMASK(2, 0)
-#define XR21V141X_UART_MODE_RTS_CTS 0x1
-#define XR21V141X_UART_MODE_DTR_DSR 0x2
-#define XR21V141X_UART_MODE_RS485 0x3
-#define XR21V141X_UART_MODE_RS485_ADDR 0x4
+#define SET_REQ 0
+#define GET_REQ 1
+
+#define CLOCK_DIVISOR_0 0x04
+#define CLOCK_DIVISOR_1 0x05
+#define CLOCK_DIVISOR_2 0x06
+#define TX_CLOCK_MASK_0 0x07
+#define TX_CLOCK_MASK_1 0x08
+#define RX_CLOCK_MASK_0 0x09
+#define RX_CLOCK_MASK_1 0x0a
+
+/* Register blocks */
+#define UART_REG_BLOCK 0
+#define UM_REG_BLOCK 4
+#define UART_CUSTOM_BLOCK 0x66
+
+/* UART Manager Registers */
+#define UM_FIFO_ENABLE_REG 0x10
+#define UM_ENABLE_TX_FIFO 0x01
+#define UM_ENABLE_RX_FIFO 0x02
+
+#define UM_RX_FIFO_RESET 0x18
+#define UM_TX_FIFO_RESET 0x1c
+
+#define UART_ENABLE_TX 0x1
+#define UART_ENABLE_RX 0x2
+
+#define UART_MODE_RI BIT(0)
+#define UART_MODE_CD BIT(1)
+#define UART_MODE_DSR BIT(2)
+#define UART_MODE_DTR BIT(3)
+#define UART_MODE_CTS BIT(4)
+#define UART_MODE_RTS BIT(5)
+
+#define UART_BREAK_ON 0xff
+#define UART_BREAK_OFF 0
+
+#define UART_DATA_MASK GENMASK(3, 0)
+#define UART_DATA_7 0x7
+#define UART_DATA_8 0x8
+
+#define UART_PARITY_MASK GENMASK(6, 4)
+#define UART_PARITY_SHIFT 4
+#define UART_PARITY_NONE (0x0 << UART_PARITY_SHIFT)
+#define UART_PARITY_ODD (0x1 << UART_PARITY_SHIFT)
+#define UART_PARITY_EVEN (0x2 << UART_PARITY_SHIFT)
+#define UART_PARITY_MARK (0x3 << UART_PARITY_SHIFT)
+#define UART_PARITY_SPACE (0x4 << UART_PARITY_SHIFT)
+
+#define UART_STOP_MASK BIT(7)
+#define UART_STOP_SHIFT 7
+#define UART_STOP_1 (0x0 << UART_STOP_SHIFT)
+#define UART_STOP_2 (0x1 << UART_STOP_SHIFT)
+
+#define UART_FLOW_MODE_NONE 0x0
+#define UART_FLOW_MODE_HW 0x1
+#define UART_FLOW_MODE_SW 0x2
+
+#define UART_MODE_GPIO_MASK GENMASK(2, 0)
+#define UART_MODE_RTS_CTS 0x1
+#define UART_MODE_DTR_DSR 0x2
+#define UART_MODE_RS485 0x3
+#define UART_MODE_RS485_ADDR 0x4
#define XR21V141X_REG_ENABLE 0x03
#define XR21V141X_REG_FORMAT 0x0b
@@ -115,7 +115,7 @@ static int xr_set_reg(struct usb_serial_port *port, u8 block, u8 reg, u8 val)
ret = usb_control_msg(serial->dev,
usb_sndctrlpipe(serial->dev, 0),
- XR21V141X_SET_REQ,
+ SET_REQ,
USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
val, reg | (block << 8), NULL, 0,
USB_CTRL_SET_TIMEOUT);
@@ -139,7 +139,7 @@ static int xr_get_reg(struct usb_serial_port *port, u8 block, u8 reg, u8 *val)
ret = usb_control_msg(serial->dev,
usb_rcvctrlpipe(serial->dev, 0),
- XR21V141X_GET_REQ,
+ GET_REQ,
USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
0, reg | (block << 8), dmabuf, 1,
USB_CTRL_GET_TIMEOUT);
@@ -159,17 +159,17 @@ static int xr_get_reg(struct usb_serial_port *port, u8 block, u8 reg, u8 *val)
static int xr_set_reg_uart(struct usb_serial_port *port, u8 reg, u8 val)
{
- return xr_set_reg(port, XR21V141X_UART_REG_BLOCK, reg, val);
+ return xr_set_reg(port, UART_REG_BLOCK, reg, val);
}
static int xr_get_reg_uart(struct usb_serial_port *port, u8 reg, u8 *val)
{
- return xr_get_reg(port, XR21V141X_UART_REG_BLOCK, reg, val);
+ return xr_get_reg(port, UART_REG_BLOCK, reg, val);
}
static int xr_set_reg_um(struct usb_serial_port *port, u8 reg, u8 val)
{
- return xr_set_reg(port, XR21V141X_UM_REG_BLOCK, reg, val);
+ return xr_set_reg(port, UM_REG_BLOCK, reg, val);
}
/*
@@ -184,18 +184,18 @@ static int xr_uart_enable(struct usb_serial_port *port)
{
int ret;
- ret = xr_set_reg_um(port, XR21V141X_UM_FIFO_ENABLE_REG,
- XR21V141X_UM_ENABLE_TX_FIFO);
+ ret = xr_set_reg_um(port, UM_FIFO_ENABLE_REG,
+ UM_ENABLE_TX_FIFO);
if (ret)
return ret;
ret = xr_set_reg_uart(port, XR21V141X_REG_ENABLE,
- XR21V141X_UART_ENABLE_TX | XR21V141X_UART_ENABLE_RX);
+ UART_ENABLE_TX | UART_ENABLE_RX);
if (ret)
return ret;
- ret = xr_set_reg_um(port, XR21V141X_UM_FIFO_ENABLE_REG,
- XR21V141X_UM_ENABLE_TX_FIFO | XR21V141X_UM_ENABLE_RX_FIFO);
+ ret = xr_set_reg_um(port, UM_FIFO_ENABLE_REG,
+ UM_ENABLE_TX_FIFO | UM_ENABLE_RX_FIFO);
if (ret)
xr_set_reg_uart(port, XR21V141X_REG_ENABLE, 0);
@@ -211,7 +211,7 @@ static int xr_uart_disable(struct usb_serial_port *port)
if (ret)
return ret;
- ret = xr_set_reg_um(port, XR21V141X_UM_FIFO_ENABLE_REG, 0);
+ ret = xr_set_reg_um(port, UM_FIFO_ENABLE_REG, 0);
return ret;
}
@@ -230,12 +230,12 @@ static int xr_tiocmget(struct tty_struct *tty)
* Modem control pins are active low, so reading '0' means it is active
* and '1' means not active.
*/
- ret = ((status & XR21V141X_UART_MODE_DTR) ? 0 : TIOCM_DTR) |
- ((status & XR21V141X_UART_MODE_RTS) ? 0 : TIOCM_RTS) |
- ((status & XR21V141X_UART_MODE_CTS) ? 0 : TIOCM_CTS) |
- ((status & XR21V141X_UART_MODE_DSR) ? 0 : TIOCM_DSR) |
- ((status & XR21V141X_UART_MODE_RI) ? 0 : TIOCM_RI) |
- ((status & XR21V141X_UART_MODE_CD) ? 0 : TIOCM_CD);
+ ret = ((status & UART_MODE_DTR) ? 0 : TIOCM_DTR) |
+ ((status & UART_MODE_RTS) ? 0 : TIOCM_RTS) |
+ ((status & UART_MODE_CTS) ? 0 : TIOCM_CTS) |
+ ((status & UART_MODE_DSR) ? 0 : TIOCM_DSR) |
+ ((status & UART_MODE_RI) ? 0 : TIOCM_RI) |
+ ((status & UART_MODE_CD) ? 0 : TIOCM_CD);
return ret;
}
@@ -249,13 +249,13 @@ static int xr_tiocmset_port(struct usb_serial_port *port,
/* Modem control pins are active low, so set & clr are swapped */
if (set & TIOCM_RTS)
- gpio_clr |= XR21V141X_UART_MODE_RTS;
+ gpio_clr |= UART_MODE_RTS;
if (set & TIOCM_DTR)
- gpio_clr |= XR21V141X_UART_MODE_DTR;
+ gpio_clr |= UART_MODE_DTR;
if (clear & TIOCM_RTS)
- gpio_set |= XR21V141X_UART_MODE_RTS;
+ gpio_set |= UART_MODE_RTS;
if (clear & TIOCM_DTR)
- gpio_set |= XR21V141X_UART_MODE_DTR;
+ gpio_set |= UART_MODE_DTR;
/* Writing '0' to gpio_{set/clr} bits has no effect, so no need to do */
if (gpio_clr)
@@ -289,12 +289,12 @@ static void xr_break_ctl(struct tty_struct *tty, int break_state)
u8 state;
if (break_state == 0)
- state = XR21V141X_UART_BREAK_OFF;
+ state = UART_BREAK_OFF;
else
- state = XR21V141X_UART_BREAK_ON;
+ state = UART_BREAK_ON;
dev_dbg(&port->dev, "Turning break %s\n",
- state == XR21V141X_UART_BREAK_OFF ? "off" : "on");
+ state == UART_BREAK_OFF ? "off" : "on");
xr_set_reg_uart(port, XR21V141X_REG_TX_BREAK, state);
}
@@ -345,7 +345,7 @@ static int xr_set_baudrate(struct tty_struct *tty,
if (!baud)
return 0;
- baud = clamp(baud, XR21V141X_MIN_SPEED, XR21V141X_MAX_SPEED);
+ baud = clamp(baud, MIN_SPEED, MAX_SPEED);
divisor = XR_INT_OSC_HZ / baud;
idx = ((32 * XR_INT_OSC_HZ) / baud) & 0x1f;
tx_mask = xr21v141x_txrx_clk_masks[idx].tx;
@@ -361,37 +361,37 @@ static int xr_set_baudrate(struct tty_struct *tty,
* oscillator and 19-bit programmable divisor. So theoretically it can
* generate most commonly used baud rates with high accuracy.
*/
- ret = xr_set_reg_uart(port, XR21V141X_CLOCK_DIVISOR_0,
+ ret = xr_set_reg_uart(port, CLOCK_DIVISOR_0,
divisor & 0xff);
if (ret)
return ret;
- ret = xr_set_reg_uart(port, XR21V141X_CLOCK_DIVISOR_1,
+ ret = xr_set_reg_uart(port, CLOCK_DIVISOR_1,
(divisor >> 8) & 0xff);
if (ret)
return ret;
- ret = xr_set_reg_uart(port, XR21V141X_CLOCK_DIVISOR_2,
+ ret = xr_set_reg_uart(port, CLOCK_DIVISOR_2,
(divisor >> 16) & 0xff);
if (ret)
return ret;
- ret = xr_set_reg_uart(port, XR21V141X_TX_CLOCK_MASK_0,
+ ret = xr_set_reg_uart(port, TX_CLOCK_MASK_0,
tx_mask & 0xff);
if (ret)
return ret;
- ret = xr_set_reg_uart(port, XR21V141X_TX_CLOCK_MASK_1,
+ ret = xr_set_reg_uart(port, TX_CLOCK_MASK_1,
(tx_mask >> 8) & 0xff);
if (ret)
return ret;
- ret = xr_set_reg_uart(port, XR21V141X_RX_CLOCK_MASK_0,
+ ret = xr_set_reg_uart(port, RX_CLOCK_MASK_0,
rx_mask & 0xff);
if (ret)
return ret;
- ret = xr_set_reg_uart(port, XR21V141X_RX_CLOCK_MASK_1,
+ ret = xr_set_reg_uart(port, RX_CLOCK_MASK_1,
(rx_mask >> 8) & 0xff);
if (ret)
return ret;
@@ -413,24 +413,24 @@ static void xr_set_flow_mode(struct tty_struct *tty,
return;
/* Set GPIO mode for controlling the pins manually by default. */
- gpio_mode &= ~XR21V141X_UART_MODE_GPIO_MASK;
+ gpio_mode &= ~UART_MODE_GPIO_MASK;
if (C_CRTSCTS(tty) && C_BAUD(tty) != B0) {
dev_dbg(&port->dev, "Enabling hardware flow ctrl\n");
- gpio_mode |= XR21V141X_UART_MODE_RTS_CTS;
- flow = XR21V141X_UART_FLOW_MODE_HW;
+ gpio_mode |= UART_MODE_RTS_CTS;
+ flow = UART_FLOW_MODE_HW;
} else if (I_IXON(tty)) {
u8 start_char = START_CHAR(tty);
u8 stop_char = STOP_CHAR(tty);
dev_dbg(&port->dev, "Enabling sw flow ctrl\n");
- flow = XR21V141X_UART_FLOW_MODE_SW;
+ flow = UART_FLOW_MODE_SW;
xr_set_reg_uart(port, XR21V141X_REG_XON_CHAR, start_char);
xr_set_reg_uart(port, XR21V141X_REG_XOFF_CHAR, stop_char);
} else {
dev_dbg(&port->dev, "Disabling flow ctrl\n");
- flow = XR21V141X_UART_FLOW_MODE_NONE;
+ flow = UART_FLOW_MODE_NONE;
}
/*
@@ -468,35 +468,35 @@ static void xr_set_termios(struct tty_struct *tty,
if (old_termios)
termios->c_cflag |= old_termios->c_cflag & CSIZE;
else
- bits |= XR21V141X_UART_DATA_8;
+ bits |= UART_DATA_8;
break;
case CS7:
- bits |= XR21V141X_UART_DATA_7;
+ bits |= UART_DATA_7;
break;
case CS8:
default:
- bits |= XR21V141X_UART_DATA_8;
+ bits |= UART_DATA_8;
break;
}
if (C_PARENB(tty)) {
if (C_CMSPAR(tty)) {
if (C_PARODD(tty))
- bits |= XR21V141X_UART_PARITY_MARK;
+ bits |= UART_PARITY_MARK;
else
- bits |= XR21V141X_UART_PARITY_SPACE;
+ bits |= UART_PARITY_SPACE;
} else {
if (C_PARODD(tty))
- bits |= XR21V141X_UART_PARITY_ODD;
+ bits |= UART_PARITY_ODD;
else
- bits |= XR21V141X_UART_PARITY_EVEN;
+ bits |= UART_PARITY_EVEN;
}
}
if (C_CSTOPB(tty))
- bits |= XR21V141X_UART_STOP_2;
+ bits |= UART_STOP_2;
else
- bits |= XR21V141X_UART_STOP_1;
+ bits |= UART_STOP_1;
ret = xr_set_reg_uart(port, XR21V141X_REG_FORMAT, bits);
if (ret)
@@ -520,7 +520,7 @@ static int xr_open(struct tty_struct *tty, struct usb_serial_port *port)
* Configure DTR and RTS as outputs and RI, CD, DSR and CTS as
* inputs.
*/
- gpio_dir = XR21V141X_UART_MODE_DTR | XR21V141X_UART_MODE_RTS;
+ gpio_dir = UART_MODE_DTR | UART_MODE_RTS;
xr_set_reg_uart(port, XR21V141X_REG_GPIO_DIR, gpio_dir);
/* Setup termios */
There are several registers that work with different models of this chipset. Simplify their namespaces. No functional changes. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- drivers/usb/serial/xr_serial.c | 224 ++++++++++++++++----------------- 1 file changed, 112 insertions(+), 112 deletions(-)