new file mode 100644
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX System Controller Firmware (SCFW)
+
+maintainers:
+ - Dong Aisheng <aisheng.dong@nxp.com>
+
+description: System Controller Device Node
+ The System Controller Firmware (SCFW) is a low-level system function
+ which runs on a dedicated Cortex-M core to provide power, clock, and
+ resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
+ (QM, QP), and i.MX8QX (QXP, DX).
+ The AP communicates with the SC using a multi-ported MU module found
+ in the LSIO subsystem. The current definition of this MU module provides
+ 5 remote AP connections to the SC to support up to 5 execution environments
+ (TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces
+ with the LSIO DSC IP bus. The SC firmware will communicate with this MU
+ using the MSI bus.
+
+properties:
+ $nodename:
+ const: 'scu'
+
+ compatible:
+ const: fsl,imx-scu
+
+ clock-controller:
+ description: |
+ Clock controller node that provides the clocks controlled by the SCU
+
+ imx8qx-ocotp:
+ description: |
+ OCOTP controller node provided by the SCU
+
+ keys:
+ description: |
+ Keys provided by the SCU
+
+ mboxes:
+ description: |
+ $ref: /schemas/mailbox/fsl,mu.yaml
+ List of phandle of 4 MU channels for tx, 4 MU channels for
+ rx, and 1 optional MU channel for general interrupt.
+ All MU channels must be in the same MU instance.
+ Cross instances are not allowed. The MU instance can only
+ be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users need
+ to make sure use the one which is not conflict with other
+ execution environments. e.g. ATF.
+ minItems: 1
+ maxItems: 10
+
+ mbox-names:
+ description:
+ include "gip3" if want to support general MU interrupt.
+ minItems: 1
+ maxItems: 10
+
+ pinctrl:
+ description: |
+ Pin controller provided by the SCU
+
+ power-controller:
+ description: |
+ Power domains controller node that provides the power domains
+ controlled by the SCU
+
+ rtc:
+ description: |
+ RTC controller provided by the SCU
+
+ thermal-sensor:
+ description: |
+ Thermal sensor provided by the SCU
+
+ watchdog:
+ description: |
+ Watchdog controller provided by the SCU
+
+required:
+ - compatible
+ - mbox-names
+ - mboxes
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/firmware/imx/rsrc.h>
+ #include <dt-bindings/input/input.h>
+ #include <dt-bindings/pinctrl/pads-imx8qxp.h>
+
+ firmware {
+ scu {
+ compatible = "fsl,imx-scu";
+ mbox-names = "tx0", "tx1", "tx2", "tx3",
+ "rx0", "rx1", "rx2", "rx3",
+ "gip3";
+ mboxes = <&lsio_mu1 0 0
+ &lsio_mu1 0 1
+ &lsio_mu1 0 2
+ &lsio_mu1 0 3
+ &lsio_mu1 1 0
+ &lsio_mu1 1 1
+ &lsio_mu1 1 2
+ &lsio_mu1 1 3
+ &lsio_mu1 3 3>;
+
+ clock-controller {
+ compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
+ #clock-cells = <2>;
+ };
+
+ pinctrl {
+ compatible = "fsl,imx8qxp-iomuxc";
+
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ IMX8QXP_UART0_RX_ADMA_UART0_RX 0x06000020
+ IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020
+ >;
+ };
+ };
+
+ imx8qx-ocotp {
+ compatible = "fsl,imx8qxp-scu-ocotp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ fec_mac0: mac@2c4 {
+ reg = <0x2c4 6>;
+ };
+ };
+
+ power-controller {
+ compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd";
+ #power-domain-cells = <1>;
+ };
+
+ rtc {
+ compatible = "fsl,imx8qxp-sc-rtc";
+ };
+
+ keys {
+ compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
+ linux,keycodes = <KEY_POWER>;
+ };
+
+ watchdog {
+ compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt";
+ timeout-sec = <60>;
+ };
+
+ thermal-sensor {
+ compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal";
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
In order to replace the fsl,scu txt file from bindings/arm/freescale, we need to split it between the right subsystems. This patch adds the fsl,scu.yaml in the firmware bindings folder. This one is only for the main SCU node. The old txt file will be removed only after all the child nodes have been properly switch to yaml. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> --- .../devicetree/bindings/firmware/fsl,scu.yaml | 162 ++++++++++++++++++ 1 file changed, 162 insertions(+) create mode 100644 Documentation/devicetree/bindings/firmware/fsl,scu.yaml