@@ -3961,60 +3961,52 @@ struct ec_response_i2c_passthru {
} __ec_align1;
/*****************************************************************************/
-/* Power button hang detect */
-
+/* AP hang detect */
#define EC_CMD_HANG_DETECT 0x009F
-/* Reasons to start hang detection timer */
-/* Power button pressed */
-#define EC_HANG_START_ON_POWER_PRESS BIT(0)
-
-/* Lid closed */
-#define EC_HANG_START_ON_LID_CLOSE BIT(1)
-
- /* Lid opened */
-#define EC_HANG_START_ON_LID_OPEN BIT(2)
-
-/* Start of AP S3->S0 transition (booting or resuming from suspend) */
-#define EC_HANG_START_ON_RESUME BIT(3)
-
-/* Reasons to cancel hang detection */
+#define EC_HANG_DETECT_MIN_TIMEOUT 5
+#define EC_HANG_DETECT_MAX_TIMEOUT 65535
-/* Power button released */
-#define EC_HANG_STOP_ON_POWER_RELEASE BIT(8)
+/* EC hang detect commands */
+enum ec_hang_detect_cmds {
+ /* Reload AP hang detect timer. */
+ EC_HANG_DETECT_CMD_RELOAD = 0x0,
-/* Any host command from AP received */
-#define EC_HANG_STOP_ON_HOST_COMMAND BIT(9)
+ /* Stop AP hang detect timer. */
+ EC_HANG_DETECT_CMD_CANCEL = 0x1,
-/* Stop on end of AP S0->S3 transition (suspending or shutting down) */
-#define EC_HANG_STOP_ON_SUSPEND BIT(10)
+ /* Configure watchdog with given reboot timeout and
+ * cancel currently running AP hang detect timer.
+ */
+ EC_HANG_DETECT_CMD_SET_TIMEOUT = 0x2,
-/*
- * If this flag is set, all the other fields are ignored, and the hang detect
- * timer is started. This provides the AP a way to start the hang timer
- * without reconfiguring any of the other hang detect settings. Note that
- * you must previously have configured the timeouts.
- */
-#define EC_HANG_START_NOW BIT(30)
+ /* Get last hang status - whether the AP boot was clear or not */
+ EC_HANG_DETECT_CMD_GET_STATUS = 0x3,
-/*
- * If this flag is set, all the other fields are ignored (including
- * EC_HANG_START_NOW). This provides the AP a way to stop the hang timer
- * without reconfiguring any of the other hang detect settings.
- */
-#define EC_HANG_STOP_NOW BIT(31)
+ /* Clear last hang status. Called when AP is rebooting/shutting down
+ * gracefully.
+ */
+ EC_HANG_DETECT_CMD_CLEAR_STATUS = 0x4
+};
struct ec_params_hang_detect {
- /* Flags; see EC_HANG_* */
- uint32_t flags;
-
- /* Timeout in msec before generating host event, if enabled */
- uint16_t host_event_timeout_msec;
+ uint16_t command; /* enum ec_hang_detect_cmds */
+ /* Timeout in seconds before generating reboot */
+ uint16_t reboot_timeout_sec;
+} __ec_align2;
- /* Timeout in msec before generating warm reboot, if enabled */
- uint16_t warm_reboot_timeout_msec;
-} __ec_align4;
+/* Status codes that describe whether AP has boot normally or the hang has been
+ * detected and EC has reset AP
+ */
+enum ec_hang_detect_status {
+ EC_HANG_DETECT_AP_BOOT_NORMAL = 0x0,
+ EC_HANG_DETECT_AP_BOOT_EC_WDT = 0x1,
+ EC_HANG_DETECT_AP_BOOT_COUNT,
+};
+struct ec_response_hang_detect {
+ uint8_t status; /* enum ec_hang_detect_status */
+} __ec_align1;
/*****************************************************************************/
/* Commands for battery charging */
Update structures and defines related to EC_CMD_HANG_DETECT to allow usage of new EC-based watchdog. Signed-off-by: Lukasz Majczak <lma@chromium.org> --- .../linux/platform_data/cros_ec_commands.h | 78 +++++++++---------- 1 file changed, 35 insertions(+), 43 deletions(-)