diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig
index d7e27b3..c457731 100644
--- a/drivers/net/wireless/rt2x00/Kconfig
+++ b/drivers/net/wireless/rt2x00/Kconfig
@@ -59,7 +59,6 @@ config RT2800PCI
 	select RT2800_LIB
 	select RT2X00_LIB_PCI if PCI
 	select RT2X00_LIB_SOC if RALINK_RT288X || RALINK_RT305X
-	select RT2X00_LIB_HT
 	select RT2X00_LIB_FIRMWARE
 	select RT2X00_LIB_CRYPTO
 	select CRC_CCITT
@@ -133,7 +132,6 @@ config RT2800USB
 	depends on USB
 	select RT2800_LIB
 	select RT2X00_LIB_USB
-	select RT2X00_LIB_HT
 	select RT2X00_LIB_FIRMWARE
 	select RT2X00_LIB_CRYPTO
 	select CRC_CCITT
@@ -196,9 +194,6 @@ config RT2X00_LIB_USB
 config RT2X00_LIB
 	tristate
 
-config RT2X00_LIB_HT
-	boolean
-
 config RT2X00_LIB_FIRMWARE
 	boolean
 	select FW_LOADER
diff --git a/drivers/net/wireless/rt2x00/Makefile b/drivers/net/wireless/rt2x00/Makefile
index 9713398..349d5b8 100644
--- a/drivers/net/wireless/rt2x00/Makefile
+++ b/drivers/net/wireless/rt2x00/Makefile
@@ -7,7 +7,6 @@ rt2x00lib-$(CONFIG_RT2X00_LIB_DEBUGFS)	+= rt2x00debug.o
 rt2x00lib-$(CONFIG_RT2X00_LIB_CRYPTO)	+= rt2x00crypto.o
 rt2x00lib-$(CONFIG_RT2X00_LIB_FIRMWARE)	+= rt2x00firmware.o
 rt2x00lib-$(CONFIG_RT2X00_LIB_LEDS)	+= rt2x00leds.o
-rt2x00lib-$(CONFIG_RT2X00_LIB_HT)	+= rt2x00ht.o
 
 obj-$(CONFIG_RT2X00_LIB)		+= rt2x00lib.o
 obj-$(CONFIG_RT2X00_LIB_PCI)		+= rt2x00pci.o
diff --git a/drivers/net/wireless/rt2x00/rt2x00config.c b/drivers/net/wireless/rt2x00/rt2x00config.c
index e225a66..f70a2b4 100644
--- a/drivers/net/wireless/rt2x00/rt2x00config.c
+++ b/drivers/net/wireless/rt2x00/rt2x00config.c
@@ -163,6 +163,34 @@ void rt2x00lib_config_antenna(struct rt2x00_dev *rt2x00dev,
 		rt2x00queue_start_queue(rt2x00dev->rx);
 }
 
+static u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev,
+				   struct ieee80211_conf *conf)
+{
+	struct hw_mode_spec *spec = &rt2x00dev->spec;
+	int center_channel;
+	u16 i;
+
+	/*
+	 * Initialize center channel to current channel.
+	 */
+	center_channel = spec->channels[conf->channel->hw_value].channel;
+
+	/*
+	 * Adjust center channel to HT40+ and HT40- operation.
+	 */
+	if (conf_is_ht40_plus(conf))
+		center_channel += 2;
+	else if (conf_is_ht40_minus(conf))
+		center_channel -= (center_channel == 14) ? 1 : 2;
+
+	for (i = 0; i < spec->num_channels; i++)
+		if (spec->channels[i].channel == center_channel)
+			return i;
+
+	WARN_ON(1);
+	return conf->channel->hw_value;
+}
+
 void rt2x00lib_config(struct rt2x00_dev *rt2x00dev,
 		      struct ieee80211_conf *conf,
 		      unsigned int ieee80211_flags)
diff --git a/drivers/net/wireless/rt2x00/rt2x00ht.c b/drivers/net/wireless/rt2x00/rt2x00ht.c
deleted file mode 100644
index a30f68c..0000000
--- a/drivers/net/wireless/rt2x00/rt2x00ht.c
+++ /dev/null
@@ -1,137 +0,0 @@
-/*
-	Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com>
-	<http://rt2x00.serialmonkey.com>
-
-	This program is free software; you can redistribute it and/or modify
-	it under the terms of the GNU General Public License as published by
-	the Free Software Foundation; either version 2 of the License, or
-	(at your option) any later version.
-
-	This program is distributed in the hope that it will be useful,
-	but WITHOUT ANY WARRANTY; without even the implied warranty of
-	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-	GNU General Public License for more details.
-
-	You should have received a copy of the GNU General Public License
-	along with this program; if not, write to the
-	Free Software Foundation, Inc.,
-	59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-/*
-	Module: rt2x00lib
-	Abstract: rt2x00 HT specific routines.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-
-#include "rt2x00.h"
-#include "rt2x00lib.h"
-
-void rt2x00ht_create_tx_descriptor(struct queue_entry *entry,
-				   struct txentry_desc *txdesc,
-				   const struct rt2x00_rate *hwrate)
-{
-	struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
-	struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0];
-	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data;
-
-	if (tx_info->control.sta)
-		txdesc->u.ht.mpdu_density =
-		    tx_info->control.sta->ht_cap.ampdu_density;
-
-	txdesc->u.ht.ba_size = 7;	/* FIXME: What value is needed? */
-
-	/*
-	 * Only one STBC stream is supported for now.
-	 */
-	if (tx_info->flags & IEEE80211_TX_CTL_STBC)
-		txdesc->u.ht.stbc = 1;
-
-	/*
-	 * If IEEE80211_TX_RC_MCS is set txrate->idx just contains the
-	 * mcs rate to be used
-	 */
-	if (txrate->flags & IEEE80211_TX_RC_MCS) {
-		txdesc->u.ht.mcs = txrate->idx;
-
-		/*
-		 * MIMO PS should be set to 1 for STA's using dynamic SM PS
-		 * when using more then one tx stream (>MCS7).
-		 */
-		if (tx_info->control.sta && txdesc->u.ht.mcs > 7 &&
-		    ((tx_info->control.sta->ht_cap.cap &
-		      IEEE80211_HT_CAP_SM_PS) >>
-		     IEEE80211_HT_CAP_SM_PS_SHIFT) ==
-		    WLAN_HT_CAP_SM_PS_DYNAMIC)
-			__set_bit(ENTRY_TXD_HT_MIMO_PS, &txdesc->flags);
-	} else {
-		txdesc->u.ht.mcs = rt2x00_get_rate_mcs(hwrate->mcs);
-		if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
-			txdesc->u.ht.mcs |= 0x08;
-	}
-
-	/*
-	 * This frame is eligible for an AMPDU, however, don't aggregate
-	 * frames that are intended to probe a specific tx rate.
-	 */
-	if (tx_info->flags & IEEE80211_TX_CTL_AMPDU &&
-	    !(tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE))
-		__set_bit(ENTRY_TXD_HT_AMPDU, &txdesc->flags);
-
-	/*
-	 * Set 40Mhz mode if necessary (for legacy rates this will
-	 * duplicate the frame to both channels).
-	 */
-	if (txrate->flags & IEEE80211_TX_RC_40_MHZ_WIDTH ||
-	    txrate->flags & IEEE80211_TX_RC_DUP_DATA)
-		__set_bit(ENTRY_TXD_HT_BW_40, &txdesc->flags);
-	if (txrate->flags & IEEE80211_TX_RC_SHORT_GI)
-		__set_bit(ENTRY_TXD_HT_SHORT_GI, &txdesc->flags);
-
-	/*
-	 * Determine IFS values
-	 * - Use TXOP_BACKOFF for management frames except beacons
-	 * - Use TXOP_SIFS for fragment bursts
-	 * - Use TXOP_HTTXOP for everything else
-	 *
-	 * Note: rt2800 devices won't use CTS protection (if used)
-	 * for frames not transmitted with TXOP_HTTXOP
-	 */
-	if (ieee80211_is_mgmt(hdr->frame_control) &&
-	    !ieee80211_is_beacon(hdr->frame_control))
-		txdesc->u.ht.txop = TXOP_BACKOFF;
-	else if (!(tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT))
-		txdesc->u.ht.txop = TXOP_SIFS;
-	else
-		txdesc->u.ht.txop = TXOP_HTTXOP;
-}
-
-u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev,
-			    struct ieee80211_conf *conf)
-{
-	struct hw_mode_spec *spec = &rt2x00dev->spec;
-	int center_channel;
-	u16 i;
-
-	/*
-	 * Initialize center channel to current channel.
-	 */
-	center_channel = spec->channels[conf->channel->hw_value].channel;
-
-	/*
-	 * Adjust center channel to HT40+ and HT40- operation.
-	 */
-	if (conf_is_ht40_plus(conf))
-		center_channel += 2;
-	else if (conf_is_ht40_minus(conf))
-		center_channel -= (center_channel == 14) ? 1 : 2;
-
-	for (i = 0; i < spec->num_channels; i++)
-		if (spec->channels[i].channel == center_channel)
-			return i;
-
-	WARN_ON(1);
-	return conf->channel->hw_value;
-}
diff --git a/drivers/net/wireless/rt2x00/rt2x00lib.h b/drivers/net/wireless/rt2x00/rt2x00lib.h
index 57ede6c..322cc4f 100644
--- a/drivers/net/wireless/rt2x00/rt2x00lib.h
+++ b/drivers/net/wireless/rt2x00/rt2x00lib.h
@@ -388,30 +388,6 @@ static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb,
 #endif /* CONFIG_RT2X00_LIB_CRYPTO */
 
 /*
- * HT handlers.
- */
-#ifdef CONFIG_RT2X00_LIB_HT
-void rt2x00ht_create_tx_descriptor(struct queue_entry *entry,
-				   struct txentry_desc *txdesc,
-				   const struct rt2x00_rate *hwrate);
-
-u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev,
-			    struct ieee80211_conf *conf);
-#else
-static inline void rt2x00ht_create_tx_descriptor(struct queue_entry *entry,
-						 struct txentry_desc *txdesc,
-						 const struct rt2x00_rate *hwrate)
-{
-}
-
-static inline u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev,
-					  struct ieee80211_conf *conf)
-{
-	return conf->channel->hw_value;
-}
-#endif /* CONFIG_RT2X00_LIB_HT */
-
-/*
  * RFkill handlers.
  */
 static inline void rt2x00rfkill_register(struct rt2x00_dev *rt2x00dev)
diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.c b/drivers/net/wireless/rt2x00/rt2x00queue.c
index 0d79278..56f9d0d 100644
--- a/drivers/net/wireless/rt2x00/rt2x00queue.c
+++ b/drivers/net/wireless/rt2x00/rt2x00queue.c
@@ -302,6 +302,85 @@ static void rt2x00queue_create_tx_descriptor_plcp(struct queue_entry *entry,
 	}
 }
 
+static void rt2x00queue_create_tx_descriptor_ht(struct queue_entry *entry,
+						struct txentry_desc *txdesc,
+						const struct rt2x00_rate *hwrate)
+{
+	struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
+	struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0];
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data;
+
+	if (tx_info->control.sta)
+		txdesc->u.ht.mpdu_density =
+		    tx_info->control.sta->ht_cap.ampdu_density;
+
+	txdesc->u.ht.ba_size = 7;	/* FIXME: What value is needed? */
+
+	/*
+	 * Only one STBC stream is supported for now.
+	 */
+	if (tx_info->flags & IEEE80211_TX_CTL_STBC)
+		txdesc->u.ht.stbc = 1;
+
+	/*
+	 * If IEEE80211_TX_RC_MCS is set txrate->idx just contains the
+	 * mcs rate to be used
+	 */
+	if (txrate->flags & IEEE80211_TX_RC_MCS) {
+		txdesc->u.ht.mcs = txrate->idx;
+
+		/*
+		 * MIMO PS should be set to 1 for STA's using dynamic SM PS
+		 * when using more then one tx stream (>MCS7).
+		 */
+		if (tx_info->control.sta && txdesc->u.ht.mcs > 7 &&
+		    ((tx_info->control.sta->ht_cap.cap &
+		      IEEE80211_HT_CAP_SM_PS) >>
+		     IEEE80211_HT_CAP_SM_PS_SHIFT) ==
+		    WLAN_HT_CAP_SM_PS_DYNAMIC)
+			__set_bit(ENTRY_TXD_HT_MIMO_PS, &txdesc->flags);
+	} else {
+		txdesc->u.ht.mcs = rt2x00_get_rate_mcs(hwrate->mcs);
+		if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
+			txdesc->u.ht.mcs |= 0x08;
+	}
+
+	/*
+	 * This frame is eligible for an AMPDU, however, don't aggregate
+	 * frames that are intended to probe a specific tx rate.
+	 */
+	if (tx_info->flags & IEEE80211_TX_CTL_AMPDU &&
+	    !(tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE))
+		__set_bit(ENTRY_TXD_HT_AMPDU, &txdesc->flags);
+
+	/*
+	 * Set 40Mhz mode if necessary (for legacy rates this will
+	 * duplicate the frame to both channels).
+	 */
+	if (txrate->flags & IEEE80211_TX_RC_40_MHZ_WIDTH ||
+	    txrate->flags & IEEE80211_TX_RC_DUP_DATA)
+		__set_bit(ENTRY_TXD_HT_BW_40, &txdesc->flags);
+	if (txrate->flags & IEEE80211_TX_RC_SHORT_GI)
+		__set_bit(ENTRY_TXD_HT_SHORT_GI, &txdesc->flags);
+
+	/*
+	 * Determine IFS values
+	 * - Use TXOP_BACKOFF for management frames except beacons
+	 * - Use TXOP_SIFS for fragment bursts
+	 * - Use TXOP_HTTXOP for everything else
+	 *
+	 * Note: rt2800 devices won't use CTS protection (if used)
+	 * for frames not transmitted with TXOP_HTTXOP
+	 */
+	if (ieee80211_is_mgmt(hdr->frame_control) &&
+	    !ieee80211_is_beacon(hdr->frame_control))
+		txdesc->u.ht.txop = TXOP_BACKOFF;
+	else if (!(tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT))
+		txdesc->u.ht.txop = TXOP_SIFS;
+	else
+		txdesc->u.ht.txop = TXOP_HTTXOP;
+}
+
 static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry,
 					     struct txentry_desc *txdesc)
 {
@@ -397,7 +476,7 @@ static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry,
 	rt2x00queue_create_tx_descriptor_seq(entry, txdesc);
 
 	if (test_bit(REQUIRE_HT_TX_DESC, &rt2x00dev->cap_flags))
-		rt2x00ht_create_tx_descriptor(entry, txdesc, hwrate);
+		rt2x00queue_create_tx_descriptor_ht(entry, txdesc, hwrate);
 	else
 		rt2x00queue_create_tx_descriptor_plcp(entry, txdesc, hwrate);
 }
