diff mbox series

[v3,2/2] mt76: mt7915: fix radar detector logic

Message ID 20210820203531.20706-2-greearb@candelatech.com (mailing list archive)
State Superseded
Delegated to: Felix Fietkau
Headers show
Series [v3,1/2] mt76: mt7915: fix STA mode connection on DFS channels | expand

Commit Message

Ben Greear Aug. 20, 2021, 8:35 p.m. UTC
From: Ben Greear <greearb@candelatech.com>

Before this patch, if AP went from ch 100 to ch 36, the radar detector
logic in the firmware was not being disabled.  This made the AP appear
to be up, but no beacons were seen on air until module reload or
reboot.

To reproduce this, I change hostapd.conf and restart hostapd.  Others
on openwrt used their UI to make changes and problem was seen, but
stil others changed channels in some other way and/or had some other
difference and could *not* reproduce it.  So, something perhaps a
bit subtle.

To fix the problem, stop depending on comparing dfs_state, store last
freq/bandwidth to detect changes in that, and streamline code that
checks to enable/disable radar detection.  And add in error checking
and dev_dbg logic so one can see what is actually happening if need
to debug this again.

Signed-off-by: Ben Greear <greearb@candelatech.com>
---
 .../net/wireless/mediatek/mt76/mt7915/init.c  |   7 +-
 .../net/wireless/mediatek/mt76/mt7915/mac.c   | 102 ++++++++++++------
 .../net/wireless/mediatek/mt76/mt7915/main.c  |  23 +++-
 .../wireless/mediatek/mt76/mt7915/mt7915.h    |   6 +-
 4 files changed, 100 insertions(+), 38 deletions(-)

Comments

Ben Greear Nov. 10, 2021, 8:32 p.m. UTC | #1
On 8/20/21 1:35 PM, greearb@candelatech.com wrote:
> From: Ben Greear <greearb@candelatech.com>
> 
> Before this patch, if AP went from ch 100 to ch 36, the radar detector
> logic in the firmware was not being disabled.  This made the AP appear
> to be up, but no beacons were seen on air until module reload or
> reboot.
> 
> To reproduce this, I change hostapd.conf and restart hostapd.  Others
> on openwrt used their UI to make changes and problem was seen, but
> stil others changed channels in some other way and/or had some other
> difference and could *not* reproduce it.  So, something perhaps a
> bit subtle.
> 
> To fix the problem, stop depending on comparing dfs_state, store last
> freq/bandwidth to detect changes in that, and streamline code that
> checks to enable/disable radar detection.  And add in error checking
> and dev_dbg logic so one can see what is actually happening if need
> to debug this again.

Back when I was working on this, someone sent me an email or chat or something
about some other way to do this that was simpler and just relied on
mac80211 timers.  But, I cannot find that email for the life of me.

In case you are reading, please resend!  Evidently this 2/2 patch had
some regression for someone so it is not acceptable upstream in
current state...maybe the mac80211 option is best.

Thanks,
Ben
Janusz Dziedzic Nov. 10, 2021, 10:36 p.m. UTC | #2
śr., 10 lis 2021 o 21:36 Ben Greear <greearb@candelatech.com> napisał(a):
>
> On 8/20/21 1:35 PM, greearb@candelatech.com wrote:
> > From: Ben Greear <greearb@candelatech.com>
> >
> > Before this patch, if AP went from ch 100 to ch 36, the radar detector
> > logic in the firmware was not being disabled.  This made the AP appear
> > to be up, but no beacons were seen on air until module reload or
> > reboot.
> >
> > To reproduce this, I change hostapd.conf and restart hostapd.  Others
> > on openwrt used their UI to make changes and problem was seen, but
> > stil others changed channels in some other way and/or had some other
> > difference and could *not* reproduce it.  So, something perhaps a
> > bit subtle.
> >
> > To fix the problem, stop depending on comparing dfs_state, store last
> > freq/bandwidth to detect changes in that, and streamline code that
> > checks to enable/disable radar detection.  And add in error checking
> > and dev_dbg logic so one can see what is actually happening if need
> > to debug this again.
>
> Back when I was working on this, someone sent me an email or chat or something
> about some other way to do this that was simpler and just relied on
> mac80211 timers.  But, I cannot find that email for the life of me.
>
> In case you are reading, please resend!  Evidently this 2/2 patch had
> some regression for someone so it is not acceptable upstream in
> current state...maybe the mac80211 option is best.
>
> Thanks,

--- a/mt7615/mac.c
+++ b/mt7615/mac.c
@@ -2034,6 +2034,11 @@ static int mt7615_dfs_start_radar_detect
  phy->rdd_state |= BIT(1);
  }

+   /* end CAC - upper layer will care about it, lock tx, beacon setup */
+   err = mt7615_mcu_rdd_cmd(dev, RDD_CAC_END, ext_phy, MT_RX_SEL0, 0);
+   if (err < 0)
+       return err;
+
  return 0;
 }

@@ -2104,11 +2109,7 @@ int mt7615_dfs_init_radar_detector(struc
  phy->dfs_state = chandef->chan->dfs_state;

  if (chandef->chan->flags & IEEE80211_CHAN_RADAR) {
-   if (chandef->chan->dfs_state != NL80211_DFS_AVAILABLE)
-     return mt7615_dfs_start_radar_detector(phy);
-
-   return mt7615_mcu_rdd_cmd(dev, RDD_CAC_END, ext_phy,
-   MT_RX_SEL0, 0);
+   return mt7615_dfs_start_radar_detector(phy);
  }
diff mbox series

Patch

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/init.c b/drivers/net/wireless/mediatek/mt76/mt7915/init.c
index f46ea989a348..543bb1e947e3 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/init.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/init.c
@@ -205,6 +205,7 @@  mt7915_regd_notifier(struct wiphy *wiphy,
 	struct mt76_phy *mphy = hw->priv;
 	struct mt7915_phy *phy = mphy->priv;
 	struct cfg80211_chan_def *chandef = &mphy->chandef;
+	int ret;
 
 	memcpy(dev->mt76.alpha2, request->alpha2, sizeof(dev->mt76.alpha2));
 	dev->mt76.region = request->dfs_region;
@@ -215,7 +216,10 @@  mt7915_regd_notifier(struct wiphy *wiphy,
 	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR))
 		return;
 
-	mt7915_dfs_init_radar_detector(phy);
+	ret = mt7915_dfs_init_radar_detector(phy);
+	if (ret < 0)
+		dev_err(dev->mt76.dev, "init-wifi: dfs-init-radar-detector failed: %d",
+			ret);
 }
 
 static void
@@ -832,7 +836,6 @@  int mt7915_register_device(struct mt7915_dev *dev)
 
 	dev->mphy.hw->wiphy->available_antennas_rx = dev->mphy.chainmask;
 	dev->mphy.hw->wiphy->available_antennas_tx = dev->mphy.chainmask;
-	dev->phy.dfs_state = -1;
 
 #ifdef CONFIG_NL80211_TESTMODE
 	dev->mt76.test_ops = &mt7915_testmode_ops;
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
index a6e142d27b60..f61c98905458 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
@@ -2404,14 +2404,29 @@  void mt7915_mac_work(struct work_struct *work)
 				     MT7915_WATCHDOG_TIME);
 }
 
-static void mt7915_dfs_stop_radar_detector(struct mt7915_phy *phy)
+int mt7915_dfs_stop_radar_detector(struct mt7915_phy *phy, bool ext_phy)
 {
 	struct mt7915_dev *dev = phy->dev;
+	int err;
+
+	dev_dbg(dev->mt76.dev, "dfs-stop-radar-detector, rdd-state: 0x%x",
+		phy->rdd_state);
+
+	err = mt7915_mcu_rdd_cmd(dev, RDD_NORMAL_START, ext_phy,
+				 MT_RX_SEL0, 0);
+	if (err < 0) {
+		dev_err(dev->mt76.dev, "mcu-rdd-cmd RDD_NORMAL_START failed: %d",
+			err);
+		/* I think best to carry on, even if we have an error here. */
+	}
 
 	if (phy->rdd_state & BIT(0))
 		mt7915_mcu_rdd_cmd(dev, RDD_STOP, 0, MT_RX_SEL0, 0);
 	if (phy->rdd_state & BIT(1))
 		mt7915_mcu_rdd_cmd(dev, RDD_STOP, 1, MT_RX_SEL0, 0);
+	phy->rdd_state = 0;
+
+	return err;
 }
 
 static int mt7915_dfs_start_rdd(struct mt7915_dev *dev, int chain)
@@ -2419,10 +2434,14 @@  static int mt7915_dfs_start_rdd(struct mt7915_dev *dev, int chain)
 	int err;
 
 	err = mt7915_mcu_rdd_cmd(dev, RDD_START, chain, MT_RX_SEL0, 0);
+
+	dev_dbg(dev->mt76.dev, "dfs-start-rdd, RDD_START rv: %d", err);
 	if (err < 0)
 		return err;
 
-	return mt7915_mcu_rdd_cmd(dev, RDD_DET_MODE, chain, MT_RX_SEL0, 1);
+	err = mt7915_mcu_rdd_cmd(dev, RDD_DET_MODE, chain, MT_RX_SEL0, 1);
+	dev_dbg(dev->mt76.dev, "dfs-start-rdd, RDD_DET_MODE rv: %d", err);
+	return err;
 }
 
 static int mt7915_dfs_start_radar_detector(struct mt7915_phy *phy)
@@ -2523,47 +2542,68 @@  int mt7915_dfs_init_radar_detector(struct mt7915_phy *phy)
 	int err;
 	struct mt7915_vif_counts counts = {0};
 
-	if (dev->mt76.region == NL80211_DFS_UNSET) {
-		phy->dfs_state = -1;
-		if (phy->rdd_state)
-			goto stop;
+	dev_dbg(dev->mt76.dev,
+		"dfs-init-radar-detector, region: %d freq: %d chandef dfs-state: %d",
+		dev->mt76.region, chandef->chan->center_freq,
+		chandef->chan->dfs_state);
 
+	if (test_bit(MT76_SCANNING, &phy->mt76->state)) {
+		dev_dbg(dev->mt76.dev, "init-radar, was scanning, no change.\n");
 		return 0;
 	}
 
-	if (test_bit(MT76_SCANNING, &phy->mt76->state))
-		return 0;
+	if (dev->mt76.region == NL80211_DFS_UNSET) {
+		dev_dbg(dev->mt76.dev,
+			"dfs-init-radar, region is UNSET, disable radar.");
+		goto stop;
+	}
+
+	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR)) {
+		dev_dbg(dev->mt76.dev,
+			"dfs-init-radar, chandef does not want radar.");
+		goto stop;
+	}
 
-	if (phy->dfs_state == chandef->chan->dfs_state)
+	ieee80211_iterate_active_interfaces(phy->mt76->hw,
+					    IEEE80211_IFACE_ITER_RESUME_ALL,
+					    mt7915_vif_counts, &counts);
+
+	if (!(counts.ap + counts.adhoc + counts.mesh)) {
+		/* No beaconning interfaces, do not start CAC */
+		dev_dbg(dev->mt76.dev,
+			"dfs-init-radar, no AP/Mesh/Adhoc vifs active, stop radar.");
+		goto stop;
+	}
+
+	/* At this point, we need radar detection, see if we have started
+	 * it already.
+	 */
+	if (phy->rdd_state) {
+		if (chandef->chan->dfs_state == NL80211_DFS_AVAILABLE) {
+			/* CAC is already complete. */
+			dev_dbg(dev->mt76.dev,
+				"init-radar, RADAR started and DFS state is AVAILABLE, call RDD_CAC_END");
+			return mt7915_mcu_rdd_cmd(dev, RDD_CAC_END, ext_phy,
+						  MT_RX_SEL0, 0);
+		}
+		dev_dbg(dev->mt76.dev,
+			"init-radar, rdd_state indicates RADAR already started,"
+			" DFS state: %d not YET available, rdd_state: 0x%x",
+			chandef->chan->dfs_state, phy->rdd_state);
 		return 0;
+	}
 
 	err = mt7915_dfs_init_radar_specs(phy);
 	if (err < 0) {
-		phy->dfs_state = -1;
+		dev_err(dev->mt76.dev, "dfs-init-radar-specs failed: %d",
+			err);
 		goto stop;
 	}
 
-	phy->dfs_state = chandef->chan->dfs_state;
-
-	if (chandef->chan->flags & IEEE80211_CHAN_RADAR) {
-		if (chandef->chan->dfs_state != NL80211_DFS_AVAILABLE) {
-			ieee80211_iterate_active_interfaces(phy->mt76->hw,
-				IEEE80211_IFACE_ITER_RESUME_ALL,
-				mt7915_vif_counts, &counts);
-			if (counts.ap + counts.adhoc + counts.mesh)
-				mt7915_dfs_start_radar_detector(phy);
-			return 0;
-		}
-		return mt7915_mcu_rdd_cmd(dev, RDD_CAC_END, ext_phy,
-					  MT_RX_SEL0, 0);
-	}
+	err = mt7915_dfs_start_radar_detector(phy);
+	dev_dbg(dev->mt76.dev, "dfs-start-radar-detector rv: %d", err);
+	return err;
 
 stop:
-	err = mt7915_mcu_rdd_cmd(dev, RDD_NORMAL_START, ext_phy,
-				 MT_RX_SEL0, 0);
-	if (err < 0)
-		return err;
-
-	mt7915_dfs_stop_radar_detector(phy);
-	return 0;
+	return mt7915_dfs_stop_radar_detector(phy, ext_phy);
 }
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/main.c b/drivers/net/wireless/mediatek/mt76/mt7915/main.c
index f3df5ea066a2..6bffddb63461 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/main.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/main.c
@@ -298,6 +298,8 @@  static void mt7915_init_dfs_state(struct mt7915_phy *phy)
 	struct mt76_phy *mphy = phy->mt76;
 	struct ieee80211_hw *hw = mphy->hw;
 	struct cfg80211_chan_def *chandef = &hw->conf.chandef;
+	struct mt7915_dev *dev = phy->dev;
+	bool ext_phy = phy != &dev->phy;
 
 	if (hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
 		return;
@@ -305,11 +307,23 @@  static void mt7915_init_dfs_state(struct mt7915_phy *phy)
 	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR))
 		return;
 
-	if (mphy->chandef.chan->center_freq == chandef->chan->center_freq &&
-	    mphy->chandef.width == chandef->width)
+	if (phy->dfs_center_freq == chandef->chan->center_freq &&
+	    phy->dfs_ch_width == chandef->width)
 		return;
 
-	phy->dfs_state = -1;
+	/* We are being moved to a new frequency/bw, still on DFS.  Stop
+	 * any existing DFS, then will start it again in the
+	 * init-radar-detector logic.
+	 */
+	if (phy->rdd_state) {
+		dev_dbg(dev->mt76.dev,
+			"init-dfs-state, channel changed, old: %d:%d  new: %d:%d, stopping radar.",
+			phy->dfs_center_freq, phy->dfs_ch_width,
+			chandef->chan->center_freq, chandef->width);
+		mt7915_dfs_stop_radar_detector(phy, ext_phy);
+	}
+	phy->dfs_center_freq = chandef->chan->center_freq;
+	phy->dfs_ch_width = chandef->width;
 }
 
 int mt7915_set_channel(struct mt7915_phy *phy)
@@ -337,6 +351,9 @@  int mt7915_set_channel(struct mt7915_phy *phy)
 
 	mt7915_mac_set_timing(phy);
 	ret = mt7915_dfs_init_radar_detector(phy);
+	if (ret < 0)
+		dev_err(dev->mt76.dev, "set-channel: dfs-init-radar-detector failed: %d",
+			ret);
 	mt7915_mac_cca_stats_reset(phy);
 
 	mt7915_mac_reset_counters(phy);
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h b/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
index f46816cefa3f..a9f55748cf1e 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
@@ -284,8 +284,9 @@  struct mt7915_phy {
 	s16 coverage_class;
 	u8 slottime;
 
-	u8 rdd_state;
-	int dfs_state;
+	u8 rdd_state; /* radar detection started bitfield */
+	enum nl80211_chan_width dfs_ch_width;
+	u32 dfs_center_freq;
 
 	u32 rx_ampdu_ts;
 	u32 ampdu_ref;
@@ -574,6 +575,7 @@  int mt7915_dfs_init_radar_detector(struct mt7915_phy *phy);
 void mt7915_set_stream_he_caps(struct mt7915_phy *phy);
 void mt7915_set_stream_vht_txbf_caps(struct mt7915_phy *phy);
 void mt7915_update_channel(struct mt76_phy *mphy);
+int mt7915_dfs_stop_radar_detector(struct mt7915_phy *phy, bool ext_phy);
 int mt7915_init_debugfs(struct mt7915_dev *dev);
 #ifdef CONFIG_MAC80211_DEBUGFS
 void mt7915_sta_add_debugfs(struct ieee80211_hw *hw, struct ieee80211_vif *vif,