| Message ID | 20220324112620.46963-1-alexandru.tachici@analog.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | net: phy: adin1100: Add initial support for ADIN1100 industrial PHY | expand |
On Thu, 24 Mar 2022 13:26:13 +0200 alexandru.tachici@analog.com wrote: > The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for > industrial Ethernet applications and is compliant with the IEEE 802.3cg > Ethernet standard for long reach 10 Mb/s Single Pair Ethernet. # Form letter - net-next is closed We have already sent the networking pull request for 5.18 and therefore net-next is closed for new drivers, features, code refactoring and optimizations. We are currently accepting bug fixes only. Please repost when net-next reopens after 5.18-rc1 is cut. RFC patches sent for review only are obviously welcome at any time.
On Thu, Mar 24, 2022 at 04:00:41PM -0700, Jakub Kicinski wrote: > On Thu, 24 Mar 2022 13:26:13 +0200 alexandru.tachici@analog.com wrote: > > The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for > > industrial Ethernet applications and is compliant with the IEEE 802.3cg > > Ethernet standard for long reach 10 Mb/s Single Pair Ethernet. > > # Form letter - net-next is closed > > We have already sent the networking pull request for 5.18 > and therefore net-next is closed for new drivers, features, > code refactoring and optimizations. We are currently accepting > bug fixes only. > > Please repost when net-next reopens after 5.18-rc1 is cut. > > RFC patches sent for review only are obviously welcome at any time. Hi Alexandru net-next is open now, you can rebase and resend this patches. Regards, Oleksij
From: Alexandru Tachici <alexandru.tachici@analog.com> The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for industrial Ethernet applications and is compliant with the IEEE 802.3cg Ethernet standard for long reach 10 Mb/s Single Pair Ethernet. The ADIN1100 uses Auto-Negotiation capability in accordance with IEEE 802.3 Clause 98, providing a mechanism for exchanging information between PHYs to allow link partners to agree to a common mode of operation. The concluded operating mode is the transmit amplitude mode and master/slave preference common across the two devices. Both device and LP advertise their ability and request for increased transmit at: - BASE-T1 autonegotiation advertisement register [47:32]\ Clause 45.2.7.21 of Standard 802.3 - BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability - BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request For 2.4 Vpp (high level transmit) operation, both devices need to have the High Level Transmit Operating Mode Ability bit set, and only one of them needs to have the High Level Transmit Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level will be used. Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT1L/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT1L/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT1L/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 10Mb/s Duplex: Full Auto-negotiation: on master-slave cfg: preferred slave master-slave status: slave Port: Twisted Pair PHYAD: 0 Transceiver: external MDI-X: Unknown Link detected: yes SQI: 7/7 1. Add basic support for ADIN1100. Alexandru Ardelean (1): net: phy: adin1100: Add initial support for ADIN1100 industrial PHY 1. Added 10baset-T1L link modes. 2. Added 10-BasetT1L registers. 3. Added Base-T1 auto-negotiation registers. For Base-T1 these registers decide master/slave status and TX voltage of the device and link partner. 4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call Base-T1 functions where registers don't match, like the auto-negotiation ones. 5. Convert MSE to SQI using a predefined table and allow user access through ethtool. 6. DT bindings for the 2.4 Vpp transmit mode. Alexandru Ardelean (1): net: phy: adin1100: Add initial support for ADIN1100 industrial PHY Alexandru Tachici (6): ethtool: Add 10base-T1L link mode entry net: phy: Add 10-BaseT1L registers net: phy: Add BaseT1 auto-negotiation registers net: phy: Add 10BASE-T1L support in phy-c45 net: phy: adin1100: Add SQI support dt-bindings: net: phy: Add 10-baseT1L 2.4 Vpp Changelog V4 -> V5: - added int pma_extable; attribute to struct phy_device; - added genphy_c45_baset1_able() function to determine base-t1 ability - replaced constant reading of MDIO_PMA_EXTABLE and checking for MDIO_PMA_EXTABLE_BT1 in phy-c45.c with the genphy_c45_baset1_able() call .../devicetree/bindings/net/ethernet-phy.yaml | 9 + drivers/net/phy/Kconfig | 7 + drivers/net/phy/Makefile | 1 + drivers/net/phy/adin1100.c | 299 ++++++++++++++++++ drivers/net/phy/phy-c45.c | 258 ++++++++++++++- drivers/net/phy/phy-core.c | 3 +- drivers/net/phy/phy_device.c | 1 + include/linux/mdio.h | 70 ++++ include/linux/phy.h | 2 + include/uapi/linux/ethtool.h | 1 + include/uapi/linux/mdio.h | 75 +++++ net/ethtool/common.c | 3 + 12 files changed, 723 insertions(+), 6 deletions(-) create mode 100644 drivers/net/phy/adin1100.c -- 2.25.1